John Lewis SBSKITC User manual

Brand: John Lewis

Model: SBSKITC

Type: User manual

John Lewis SBSKITC is a Side by Side unit designed to combine three different units in one: a cooler section, a beverage storage section, and a freezer section. The sections are not reversible and must be positioned in order from right to left as follows: cooler, beverage storage, freezer.

To install the unit, it is important to first place it upright and remove all packaging, including corner protections. You will then need to screw the M8 nuts onto the respective front feet and the front feet onto the bracket of the unit. Adjustable rear feet must be positioned on the compressor support plate and fixed with four 4.2x13 screws. The front parts of the adjustable rear feet are blocked by fixing two clamps with two M4x6 screws.

SBSKITC

Side by Side

Instruction manual

Important information

• Do not install the unit on your own or have unqualified personnel install it.

• Improper installation may result in damage, malfunctioning or risk of electric shock.

• This Side by Side unit must have the cooler section on the right side, the beverage storage section in the

middle and the freezer section on the left side; the positions are not reversible.

• The power cords must be connected separately to a suitable socket.

• All information regarding each section of this equipment is given in the user instructions to be found inside

the cooler section. Please read the instructions carefully before carrying out any operation.

• Removal and reinstallation of this unit must only be carried out by authorized personnel.

• Please keep these installation instructions for future reference or further installation.

- Carefully place the unit on the floor, following the instructions on the packaging to make sure the unit is

facing upwards.

- Open the bottom part of packaging and remove the corner protection.

- Screw the M8 nuts (5) on the respective front feet , see Fig. (1).

- Screw the front feet (6) on the bracket of the unit see Fig. (2) using the dimension indicated in Fig. (3).

- Position the adjustable rear feet (19) on the compressor support plate, see Fig. (4).

•

• Operation to be carried out on each units:

- Fix the adjustable rear feet (19) with four 4.2x13 screws (3), see Fig. (4).

During this operation use the protective glasses before proceding with the operation.

Block the front parts of the adjustable rear feet fixing two clamps (7) with two M4x6 screws (4), see Fig. (5)..

- Carefully reposition the appliance in the upright position and remove the packaging completely.

• Glue two spacer spongers on the right side of the freezer.

• Glue two spacer spongers on both sides of the wine cooler.

• Glue two spacer spongers on the left side of the cooler.

Use the distances indicated in the fig. under neath.

• Bring the wine cooler unit near to cooler unit.

• Only if necessary adjust the front feet so that the units are both the same height, see Fig. (6).

• Wrench supplied in the assembly kit.

• Insert joining bracket (9) Fig. (7).

• Fix the joining bracket with four M5x18 screws (2), see Fig. (8).

• Repeat the operation between freezer unit and wine cooler unit.

• Only if necessary adjust the front feet so that the units are both the same height, see Fig. (9)

• Wrench supplied in the assembly kit.

• Fix the joining bracket (11) with four 4.2x13 screws (3) using the holes in the top of the sides,

see Fig. (12).

• The bracket (11) must be positioned so that the side of the bracket with the hole in the centre part

protrudes as shown in fig. (12).

• Fix the joining bracket (12) with two 4.2x13 screws (3) using the holes in the top of the freezer

side, see Fig. (13).

• Fix the joining bracket (12) with the wine cooler upper hinge using two M5x18 screws (2), see Fig. (13).

• Fix the joining bracket (10) with six 4.2x13 screws (3) using the holes in the sides, see Fig.(14).

Fix the joining bracket (10) with four 4.2x13 screws (3) using the holes in the sides, see Fig. (15)

•

• If it is necessary to amend the level of the doors (only cooler and freezer units), partially unscrew the hinge

screws, related to the door to be adjusted, and move the hinge.

• Repeat the operations for the cooler and freezer doors until a correct alignment is obtained.

• Before proceding with the assembly of the top (14):

Remove the three polystyrene protections inside the front part Fig. (16).

- Remove the protective film from the top panel (14).

• Position the top with the doors open so that the bottom front part fits under the top hinges, see Fig. (17)

• Push the top so that its rear welt is touching the back of the units, see Fig. (18).

• During this operation push the three points indicated, so that the top panel can be correctly introduced, see Fig.(19)

• Fix the top frontaly with three M5X12 screws (1), see Fig. (20).

• Fix the back of the top with four 4.2x13 screws (3), see Fig. (21).

• Fit the trims "18" between the units (freezer/wine cooler - wine cooler/cooler) by pressing along the

entire profiles, see figure below.

• Before proceeding with the fixing of (16,17) side strips remove the protective film.

• Insert the side strip, see fig. (22)

• Align the outside of the side strip with the side of the unit and fix it with a 4.2x13 screw (3).

Repeat the operation for the left side, see fig. (23).

•

• Install the appliance.

You should also ensure that air can circulate freely around the back and the top of the cabinet.

Position the assembled Side by Side:

• At least 150 mm from any overhanging kitchen furniture.

• Slacken the screws and insert the spacer (13) under the screw head, then re-tighten the screws, see Fig. (24).

(13)

• After the positioning of the appliance, verify the door alignment.

• If necessary regulate the rear feet and front feet to level the appliances. See Fig. (25) and Fig. (26).

• Lock the M8 nuts (5), see Fig. (27).

• How to adjust the door alignment.

• Some examples are indicated in the figure under neath .

• Before proceeding with the fixing of the plinth (15):

- Remove the polystyrene protections with care without damaging the plinth, Fig. (31).

- Remove the protection film.

Remove the plastic protection, Fig. (32).

• Fit the plinth (15) so that the inner hook couples with the joining bracket as shown in the illustration (see Fig. 34).

• The plinth must be introduced under the wine-cellar door stopper (see Fig. 33).

• Fix the front of the plinth (15) with three M5X12 screws (1), see Fig. (35).

Page is loading ...

John Lewis SBSKITC User manual

John Lewis SBSKITC User manual

John Lewis SBSKITC User manual

Related papers

Other documents