Luminor MOD-EMU User manual

Brand: Luminor

Model: MOD-EMU

Type: User manual

Operaon & Installaon Instrucons

EQUIPMENT MODULES

ACKCOMB

OWNER’S MANUAL

illuminating technologies for life

Table of Contents

Emulator Module .............................................. 1

Remote Alarm Module ...................................... 2

4-20 mA Module................................................ 3

Solonoid Module ............................................... 4

SHERPA Water Quality Monitor Module ........... 8

UV Concierge Module ..................................... 10

*Modules not available in all markets.

*TheseinstruconsareavailableinsocopyviaemailfromLuminorCustomerService.

CAUTION: The appliance is not to be used by persons (including children) with reduced

physical, sensory or mental capabilies, or lack of experience and knowledge, unless they

have been given supervision or instrucon.

Children should be supervised so that they do not play with the appliance.

1|Page

EMULATOR MODULE

MODEL # MOD-EMU

The Emulator module comes with a male

IEPconnecon(InniteExpandability

Port).Priortostart-up,rstensureallthe

toggleswitchesforthe“ModuleAlarms”

and“LampAlarm”areintheOFF(toggle

up)posion.PlugtheEmulatorconnector

intotheIEPontheBLACKCOMB/HO

controller,thenpluginthecontroller

powercord.

ToEmulateaparcularmodulefailure,

togglethecorrespondingswitchtothe

ON(toggledown)posion.Thealarm

can be cleared by returning the switch to

itsOFF(toggleup)posion.Thedevice

alsocanemulatetheUVintensityreportedbyaUVsensormodule.Turningtheright“UV”

knobintheclockwisedireconwillincreasetheintensity,whileturningitcounterclockwisewill

decreasetheintensity.Pleasenotethattoseeallthecapabiliesofthesensor,youwillneed

tocycletheintensitythroughtherangeof49through66%.The“DaysRemaining”cyclecan

alsobeadjustedbyturningthele“Days”knob.Theemulatormodulemustonlybesupplied

atSELV.

*Fordealeruseonly.Notavailableforsaletogeneralpublic.

Emulation Module

Module Alarms

Closed Open

Days UV

Sensor Solenoid 4-20 LampRemote Alarm

Solenoid Status

MOD-EMU

BLACKCOMB

Controller

BLACKCOMB-HO

Controller

IEP

connecon

IEP

connecon

2|Page

REMOTE ALARM MODULE

MODEL # MOD-RAM

TheRemoteAlarmmodulecomeswithbothamaleandfemale

IEPconnecon(InniteExpandabilityPort).Toiniatethemodule

simplyplugthemaleplugintotheIEPontheStandardorHigh

Outputcontroller,orintoanyotherBLACKCOMBmodulethat

containsanIEP(sensor,4-20mAmodule,solenoidmodule,etc.)

and then restart the system.

TheRemoteAlarmmoduleisapairofdrycontactsandcanbe

usedtoconnectthecontrollertoaPLCbasedsystem,analarm

buzzer(orlight),oran“OK”light.Maximumcontactrangis30V

/1A.Iftheconnecteddevice(eg.lightorbuzzer)exceedsthe1A

currentrangthenusetheRemoteAlarmModuletocontrolan

appropriatelyratedrelay.

TheremotealarmmodulemustonlybesuppliedatSELV.

Disconnectpowersupplybeforeservicing.

“OK”

Light

Customer

Power Supply

Maximum 30V

“FAIL” Light/Buzzer

Autodialer

Customer

Power Supply

Maximum 30V

Sensor IEP

Installaon

IEP

connecon

BLACKCOMB

Controller

BLACKCOMB-HO

Controller

IEP

connecon

IEP

connecon

Figure 1

Secure module to

wall with screws

Figure 2

IEPconnecon

IEP

3|Page

4-20 mA MODULE

MODEL # MOD-420

The4-20mAmodulecomeswithbothamaleandfemaleIEP

connecon(InniteExpandabilityPort).Toiniatethemodule

simplyplugthemaleplugintotheIEPonthecontroller,orinto

anyotherBLACKCOMBmodulethatcontainsanIEP(sensor,

remotealarm,solenoidmodule,etc.)

The4-20mAmodulemustonlybesuppliedatSELV.Disconnect

powersupplybeforeservicing.

Connect “LOOP” Connecons as follows:

Sensor IEP

Installaon

IEP

connecon

BLACKCOMB

Controller

BLACKCOMB-HO

Controller

IEP

connecon

IEP

connecon

Figure 1

Secure module to

wall with screws

Figure 2

IEPconnecon

IEP

LOOP Specifications

Power Supply: Min 5 volts

Max 30 volts

Power Supply

PLC

Data Logger

Power Supply (must be SELV):

Min 5 volts

Max 30 volts

4|Page

SOLENOID MODULE

MODEL # MOD-SOL1 (in 110V, NEMA 5-15 plug)

MOD-SOL2 (in 230V, CEE 7/7 plug)

MOD-SOL3 (in 230V, BS 1363 plug)

MOD-SOL4 (in 230V, AS/NZS 3112 plug)

TheSolenoidModuleisdesignedtoconnectaNORMALLY

CLOSEDlinevoltagesolenoidvalvetothecontroller.Itis

possibletousea12Vor24Vnormallyclosedsolenoidby

replacingtheACpowercord.Notethatthemaximumcontact

rangis240VAC(50-60Hz)/30VDC/2A.

LOCATION

Step 1) Findasuitablelocaononthewallforthesolenoid

module. The module must be installed close enough to the

controller,ortheUVsensortobeabletopluginthemale

IEP connector. The module must also be installed close

enough to the actual solenoid valve and this distance will

bedependentonthecordlengthoftheparcularsolenoid

valve that is used.

Step 2)Pickalocaonforthesolenoidvalveandinstallas

perthemanufacturer’sdirecons.Thesolenoidmodule

requiresbareleadsforconnecontoterminalblocks,so

ifthesolenoidcablehasaplugaached,removetheplug

andstripthewirestoasuitablelength.

INSTALLATION

Step 1) MakesurethesolenoidvalvecableisNOTpluggedintotheelectricaloutlet.Insert

thesolenoidvalvecablethroughthecenterholeofthemiddlestrainrelief.Connectthethree

electricalwirestotheterminalblockthatismarked“SOLENOID”(seeFig.2).Connectthe

groundwireintheposionmarked“GND”,thelinevoltagewireintheposionmarked“L1”

andtheneutralwireintheposionmarked“N”.Typicalwirecolourconguraonsaremarked

directlyonthecircuitboardtotheleoftheSOLENOIDterminalblocktoaidinthisprocess

(seeFig.3)Ifyouareunsureofthecorrectwiringconguraonforyouparcularsolenoid

valve,pleasecontactanapprovedelectricalcontractor.Onceallthelinevoltageconnecons

havebeenmade,ghtenthestrainreliefnuttosecurethecabletothesolenoidmodule.

Figure 3

WiringColourGuide

Figure 2

SolenoidWireInstallaon

Figure 1

Secure

module to

wall with

screws

5|Page

Step 2) Plugthesolenoidvalveintotheapplicableelectrical

outlet.Atthisstage,thefunconalityofthesolenoidvalve

canbetestedbypressingthesolenoidtestbuonlocatedon

theupperleofthecircuitboard.Manuallydepressing(and

holding)thisbuonwillcompletetheelectricalcircuitandwill

openthenormallyclosedsolenoidvalve.Youshouldbeableto

heartheacvaonofthesolenoidvalveatthisstagetoensure

thevalveisfunconingproperly(seeFig.4).

Step 3) MakesureyourUVcontrollerisunpluggedfromthe

powersource.Oncealltheseconneconshavebeenmade,

axthemaleIEPplugofthesolenoidmodulecableintothe

IEPportonthecontroller(seeFig.5),oranyotheravailable

IEPportsuchastheUVsensor,4-20mAmoduleorremote

alarmmodule.ItdoesnotmaerwhichIEPportanymodule

isaachedto,aslongastheyareaached.

OPERATION

Step 1) PlugtheBLACKCOMBcontrollerintothepower

sourceandmakesurethesolenoidmoduleisacvatedon

thecontroller.Duringthestart-upsequence,theSOLENOID

MODULEscreenwillindicatea“inialized”whenthemodule

isacvatedproperly(seeFig.6).

Figure 4

SolenoidTestBuon

Figure 6

Solenoid

Acvaon

Screens

Sensor IEP

Installaon

IEP

connecon

BLACKCOMB

Controller

BLACKCOMB-HO

Controller

IEP

connecon

IEP

connecon

Figure 5

IEPconnecon

IEP

6|Page

Step 2) Thecontrollerwillonlynofyyouwhenthereisafailure

modewherebythesolenoidmodule(andconnectedsolenoidvalve)

willbeacvated.OntheBLACKCOMB5.1system,thesolenoid

modulewillbeacvated(shungotheowofwater)uponLAMP

FAILURE(seeFig.7).Toremedythis,replacetheUVlampandrestart

thesystemasperthedireconsoutlinedintheOwner’sManual.

Step 3) OntheBLACKCOMB6.1systemwhereaUVsensorisinstalled,

thesolenoidmodulewillbeacvated(shungotheowofwater)

uponaLOWUVcondion(lessthan50%)(seeFig.8).Toremedythis,

youwillneedtoaddressthereasonforthislowUVcondionwhich

may be due to a dirty UV sensor and quartz sleeve, a lamp that is

not eming enough UV energy, or a change in the water quality.

PleaserefertotheUVsystemsOwner’sManualforcorrecveacon

procedures.

Figure 7

LAMPFAILUREScreen

Step 4) To determine what posion the solenoid valve is currently in, the solenoid module

incorporates three lights on the circuit board (see Fig. 9). When the solenoid is in the OPEN

posionagreenlightwillappearonthecircuitboardbesidetheword“OPEN”.Whenthevalve

isCLOSED,aredlightwillappearonthecircuitboardbesidetheword“CLOSED”.Andwhenthe

solenoidisinanOVERRIDEposion,anamberlightwillappearonthecircuitboardbesidethe

word“OVERRIDEON”.

Figure 8

LOWUV

Screens

Figure 9

Solenoid Status

(Colour)

Boil Water Advisory: If any failure occurs on a BLACKCOMB UV system, the water

must not be used for human consumpon unl the system is returned to a safe operaonal

mode. If the water is used for human consumpon during this period, the water must be

boiled (minimum 20 minutes at a full boil) prior to consumpon.

EMERGENCY BYPASS

Inacasewherethesolenoidvalvehasbeenacvated(valveisclosedandnowaterisallowed

toow),thesolenoidmodulehastheabilitytobypassthesolenoidvalveincaseofan

emergencyneedofwater.Toiniatethisbypass,depressthebuonlabeled“OVERRIDE”

locatedinthelowerleporonofthecircuitboard(seeFig.10)

7|Page

Figure 10

SolenoidBypass

Buon

Oncethisbuonhasbeenpressed,thesystemwillremaininthis

overridemoderegardlessofwhetherornotthecondioncausingthe

solenoidacvaonhasbeenremediedornot.Toresetthesystem,

thepowertothecontrollermustbeshutoandrestarted.While

inthisoverridemodethecontrollerwillintermientlydisplayared

“SOLENOIDOVERRIDE”screen(seeFig.11).

Figure 11

SOLENOIDOVERRIDE

Screen

DISABLING EMERGENCY BYPASS

Incertainregulatedapplicaons,theavailability,anduse,

oftheemergencybypassfeaturemaybeinviolaonofthe

local,state/provincialcodes.Ifthisisthecase,thebypass

featurecaneasilybedisabledbyphysicallyremovingthe

bypassbuon.Toaccomplishthis,carefullyuseapairof

needlenosepliersandphysicallyremovetheactualbypass

buon(marked“OVERRIDE”)fromthecircuitboard.

Figure 12

SOLENOIDFAILURE

Screen

OTHER FAILURE MODES

Intheeventthereisanissuewiththesolenoidconneconfrom

theIEPcabletothecontroller,thesystemwillregistera“SOLENOID

FAILURE”screenonthecontroller(seeFig.12).

CAUTION: BEFORE PERFORMING ANY

WORK ON THE SOLENOID MODULE, THE

POWER CORD MUST BE DISCONNECTED

FROM ITS POWER SOURCE (WALL PLUG).

8|Page

WATER QUALITY

MONITOR MODULE

MODEL # MOD-SHERPA

ThemodulecomeswithaSHERPATransmierandaSHERPARemoteDisplay.TheTransmier

connectstoaBLACKCOMBandBLACKCOMB-HOcontrollerandtransmitsthecontroller’sstatus

wirelesslytotheRemoteDisplay.EveryTransmierandRemoteDisplayispairedtogether

andusesencryptiontocreateareliableandsecurecommunicationlinkbetweenthetwo

devices.EveryTransmiersupportsuptoveRemoteDisplays.AdditionalRemoteDisplays

canbepurchasedandinstalledseparately.Referto‘PairinganAdditionalRemoteDisplay’for

additionalRemoteDisplayinstallation.

Sensor IEP

Installaon

IEP

connecon

BLACKCOMB

Controller

BLACKCOMB-HO

Controller

IEP

connecon

IEP

connecon

Installation

Step 1)PowerotheBLACKCOMBorBLACKCOMB-HOcontroller.

Step 2)PlugthemaleplugoftheSHERPATransmierintotheIEP(InniteExpandability

Port)onthecontroller,orintoanyotherLUMINORmodulethatcontainsanIEP

(sensor,4-20mAmodule,solenoidmodule,etc.)andthenrestartthesystemNote1.

Step 3)ToReceivetheBLACKCOMBor

BLACKCOMB-HOcontroller’s

status on the SHERPA Remote

Display,plugtheAC/DCwall

adapterintothePowerPorton

theSHERPARemoteDisplay(5V

Max)andslidetheswitchto

theONposion.

Back of

Remote

Display

SHERPA Transmier

SHERPA Remote Display

50m/164

(Note2)

9|Page

Operation

SHERPA Remote Display

Status LED’s

Good

(Green) Waterissafeforconsumption.NoActiveAlarms.

Caution

(Yellow)

Watermaynotbesafeforconsumption.

ActiveMinorAlarm,checksystemfordetails.

Alarm

(Red)

WaterisNOTsafeforconsumption.

ActiveMajorAlarm,checksystemfordetails.

Comm. LED

OFF Communication is working.

Flashing

CommunicationisNOTworking.

Remote Display is Out-of-Range2, Transmier is disconnected

OR controller is powered o.

ON RemoteDisplayisaemptingtopairwithalocal

transmierinproximity.

Power

Switch

IRemoteDisplayPoweredON

O RemoteDisplayPoweredOFF

NOTE 1: Not Compable with MOD-RAM. The SHERPA gets detected as a “Remote Alarm” on

BLACKCOMB or BLACKCOMB-HO controllers during the start-up sequence.

NOTE 2: The Wireless Range can vary based on the installation environment; objects, walls

and metal obstacles can interfere and degrade the wireless signal. Best suited for residential

applications.

Pairing an Additional Remote Display

TopairanadditionalRemoteDisplaytoacurrentlyinstalledTransmier:

Step 1)PowerONtheAdditionalRemoteDisplaywithin5m(15)proximitytothe

transmier;bysimplypluggingtheAC/DCwalladapterintothePowerPorton

theRemoteDisplayandslidingtheswitchtotheONposition.

Step 2)TheRemoteDisplayperformsself-pairingwiththelocaltransmier.Oncepaired

theCommunicationLEDontheRemoteDisplaywillturnOFFandaStatusLED

willturnON.

Step 3)Oncepairingiscomplete,relocatetheRemoteDisplaytoanylocation2.

10|Page

UV CONCIERGE MODULE

MODEL # MOD-APP

TheUVConciergemoduleconnectstoyourwirelessnetwork(WiFi)andtransmitsyourUV

system’sstatustotheuvconcierge.comwebpage.Youcanthenviewyourstatusonlinefrom

anywhereyouhaveinternetaccess,andreceiveemailorSMSnocaonsofyoursystem’s

status on your mobile device.

TheUVConciergemodulecomeswithbothamaleandfemaleIEPconnecon(Innite

ExpandabilityPort).ToiniatethemodulesimplyplugthemaleplugintotheIEPonthe

StandardorHighOutputcontroller,orintoanyotherBLACKCOMBmodulethatcontainsanIEP

(sensor,4-20mAmodule,solenoidmodule,etc.),plugintheincludedpoweradaptertothe

wallandyourUVConciergemodule,andthenrestarttheUVsystem.

Oncethesystemisiniatedasabove,youwillneedtoprovideyourWiFilogincredenalsto

thesystem.InstalltheUVConciergeapponyouriOSorAndroiddevicebysearchingforitin

youriOSAppStoreorGooglePlaystore,orscantheQRcodebelow:

Fromtheapp,clicktheConnectDevicebuon,andfollowthepromptstoselectyourWiFi

networkandenterinyourpassword.

Oncetheappreportsthemoduleisconnected,addthedevicetoyouraccountbyoneofthe

threefollowingmethods:

Sensor IEP

Installaon

IEP

connecon

BLACKCOMB

Controller

BLACKCOMB-HO

Controller

IEP

connecon

IEP

connecon

11|Page

If you do not currently have a uvconcierge.com account: FromtheUVConciergeapp,click

“Adddevicetoaccount”.Thismethodwillautomacallypopulateyourmodulekeyforyou.

Make note of the Module Key from the label on your UV Concierge module. Goto

uvconcierge.comandclickthe“Registeranewdevice”link.Youwillneedthemodulekeyto

successfullyregisteryourmodule.

If you currently have a uvconcierge.com account: FollowoneoftheabovetwooponsORlog

intoyouraccount,select(oradd,thenselect)thelocaonyou’dliketohavethedevice,thenclick

the“Addadevicebuon”.Youwillneedthemodulekeytosuccessfullyregisteryourmodule.

App Troubleshoong

The app does not nd my UV Concierge module

EnsureyouhavepluggedyourUVConciergemoduleintothepoweroutletusingtheincluded

poweradapter.

I’m stuck at “Waing for system to complete startup”

Youmustrestartyoursystembyunpluggingandplugginginthecontrollerpowercordaer

pluggingintheUVConciergemodule.OncethecontrollerdetectstheUVConciergemodule

andthestartuprouneisnished,youwillautomacallypassthissecon.Aerstartupis

complete,youcanpressandholdthecontrollerbuonfor3secondstoseewhatmodulesit

currentlydetects.IfthecontrollerisnotdetecngtheUVConciergemodule,checkyourIEP

connecons.Connectonemoduletothecontrolleratametotesteachmoduleindividually.

Withmulplemodules,theorderofthedaisychain(whichdeviceispluggedintowhich)does

notmaer.

I get a “Pairing Failed” error

Aertheappndsyourdevice,youmustenterinthe6numbersdisplayedonthecontroller

intoyourapp,includingleadingzeros.Ifyouaresllstuck,tryrestarngtheUVConcierge

modulebyunpluggingitandpluggingitbackin.TryrestarngyouriOS/Androiddevicealso.If

theissuepersists,trywithanotheriOSorAndroiddevice.

12|Page

13|Page

illuminating technologies for life

80SouthgateDrive,Unit4

Guelph,Ontario,CanadaN1G4P5

P:519-837-3800

TF:855-837-3801

F:519-837-3808

info@luminoruv.com

www.luminoruv.com

PN: 910352

VersionDate:04-2022

Luminor MOD-EMU User manual

Brand: Luminor

Model: MOD-EMU

Type: User manual

Download PDF

report

Luminor MOD-EMU User manual

Luminor MOD-EMU User manual

Related papers

Other documents