Urbana U37 Installation guide

Brand: Urbana

Model: U37

Type: Installation guide

Urbana U37 offers a variety of features to enhance your living space. With its sleek design and advanced technology, this fireplace promises both ambiance and warmth. It's crafted to provide a realistic flame effect, adjustable heat output, and a convenient remote control for effortless operation. The Urbana U37 also boasts safety features like automatic overheat protection and a cool-to-touch exterior, ensuring peace of mind during use. Whether you're seeking a cozy atmosphere or supplemental heat, this fireplace delivers both style and functionality.

U37 FIREPLACE

Installation Reference Guide

REFER TO OWNER’S MANUAL FOR SPECIFIC INSTALLATION REQUIREMENTS AND ADDITIONAL PRODUCT INSTRUCTIONS

Clearance to Combustibles

79 ½”

2172 mm

Refer to Table on left

46 /”

1359 mm

44 /”

1283 mm

1” 25mm

Clearance from

framing studs

to venting

Minimum

Framing Dimensions

Note: When framing the unit, care

must be taken to consider the final

floor thickness, the bottom of the

fireplace must sit flush with the

finished floor to ensure proper fit of

the surround components

Note: Vent size: 8 x 11” Rigid Co-Axial

Minimum Depth

(2” facing mat.) 22 /” 578 mm

Maximum Depth

(½” facing mat.) 24 /” 616 mm

Width 46 / ” 1175 mm

Header Height 44 /” 1130mm

Enclosure Ceiling 79 ½” 2020 mm

A - Finishing edge to side wall 3 /" 89 mm

B - Minimum clearance to enclosure ceiling 79 ½"2020 mm

C - Minimum clearance to mantel height 38 ⁄” 981 mm

D - Front of door to edge of floor protection 0" 0 mm

E - Minimum alcove width 44 /" 1137 mm

†

† - Additional ceiling height required if using 5x8 co-axial venting, refer to installation manual.

COMBUSTIBLE

NON COMBUSTIBLE

Wood

raming

Header

Drywall

Non

Combustible

Board

Sidewall

12”

3½”

5/8”

22¾” - 24¼”

[578 - 629mm]

12” Non-

Combustible

Zone

69¼"

1759mm

79½

[2007mm]

Use one 24" vent

section to achieve

minimum rise in

order for this

dimension to work.

30” Minimum

[762mm]

4 3/4” [121mm]

First Elbow Only

Non-Combustible Board

Placement

Mantel Projections

Mantel graph dimensions are measured from the bottom

of the replace, if you wish to reference the mantel height

from the tiling edge subtract 32 ⁄ inches (829mm) from the

mantel height depicted on the graph. If you plan to install a

TV above your replace refer to the appropriate section of the

owner’s manual for available options. It is acceptable to install

a combustible mantel over top of the non-combustible board.

If using the Cool Surface System, refer to the graph on the

following page to determine the required mantel height.

Minimum Venting Requirements

This appliance uses a 11” (280 mm) exhaust / 8” (203mm) air intake

vent pipe system. For safe and proper operation of the appliance

follow the venting instructions exactly. Deviation from the

minimum vertical length can create diculty in burner start-up

and sooting. Allow several minutes for the ame to stabalize after

ignition under extreme vent congurations. It is recommended for

vent lengths that pass through unheated spaces (garages, attics,

crawl spaces) be insulated to minimize condensation.

NOTE: At least 3” (76mm) of clearance is required above vent when

passing through an exterior wall when horizontally terminating.

Fireplace Dimensions

37 5/8" [956]

36" [914]

44 3/4" [1137]

46 1/8" [1172]

22 1/4" [565]

22 3/8"

[568]

24 7/8" [632]

22 3/4" [578]

24 1/4" [616]

8" x 11"

vent

32 5/8" [829]

44 1/2" [1130]

2" [50]

9 5/8" [244]

5 1/2" [140]

3" [76]

8 1/2" [216]

11 1/8" [283]

Gas Input

Electrical Input

M A NTEL H E I G H T

M A NTEL D E P T H

2 4 6 8 10 12 14

4” MANTEL

12” MANTEL

8” MANTEL

†Additional ceiling and thimble height required if using 5x8 co-axial venting, refer to

†

installation manual

Cool Surface System Framing

Framing Option 1:

Front Discharge (ush wall installations)

Construct the framing in a way that provides a minimum 42 inch (1067mm) by 3 inch

(76mm) gap at the top of the facing wall. It is essential that these dimensions are

respected and not to deviate away from them when using combustible materials inside

the chase (see Figure 1).

Note: If you wish to construct the CSS air discharge part way up a tall wall then it is essential to

build a false ceiling inside the chase at the desired height to direct the rising heat out of the gap.

Figure 1: Framing Option 1

76mm

Minimum

42"

1067mm

Minimum

71 1

1816mm

Minimum

305mm

1133mm

127mm

Maximum

Non-Combustible board NOT

mandatory for CSS Install

CSS Air Discharge

37 5

Figure 2: Open Chase

Framing Option 2:

Open Chase (built-out installations)

This could be considered the most discreet option when considering the CSS. The chase must be constructed in a way that stops short

of the ceiling, leaving it totally vented above. Minimum framing dimensions must be followed when constructing this option and not to

deviated from them when using combustible materials. Consider Optional 3: Valance to work in conjunction with this option.

3" MIN

Figure 3: Open Chase

Iso View

76mm

Minimum

121mm

Minimum

152mm

Minimum

Wall Mounted Object

Mantel Projections with Cool

Surface System

Activating the Cool Surface System decreases the required

height of the mantel. Use the graph on the right to determine the

mantel height when using the Cool Surface System. Mantel graph

dimensions are measured from the bottom of the replace, if you

wish to reference the mantel height from the tiling edge subtract

32 ⁄ inches (829mm) from the mantel height depicted on the

graph. If you plan to install a TV above your replace refer to the

appropriate section of the owner’s manual for available options. It

is acceptable to install a combustible mantel over top of the non-

combustible board.

2 4 6 8 10 12 14

4” MANTEL

8” MANTEL

12” MANTEL

M A NTEL H E I G H T

M A NTEL D E P T H

Cool Surface System Framing

Framing Option 4: Side Discharge

Construct the framing in a way that provides two gaps, one on each side of the chase as shown in Figure 7. Each gap should be a minimum of

21 inch (533mm) by 3 inch (76mm). It is essential that these dimensions are followed and not to deviated from them when using combustible

materials inside the chase (see Figure 6).

Optional: False Ceiling

If your ceiling dimension is greater than the minimum (See Figure 1) You may want the CSS air discharge lower on the wall. This false ceiling

is required to properly evacuate heat from the chase. (See Figure 8).

121mm

Minimum

76mm

533mm

127mm

Minimum

Maximum

76mm

Minimum

False Ceiling

121mm

Minimum

Framing Option 3: Valance

A valance may be desired to accentuate or hide the CSS outlet. Consider framing option 1 or 2 to utilize the valance feature. This is an

optional decorative feature that covers up the CSS outlet gap. Minimum opening and valance dimensions must be followed to ensure safe

heat dissipation. Combustible materiel is acceptable when constructing the valance. It is acceptable to wrap the valance around the three

sides of a built out chase (Option 2).

Minimum

102mm

25mm

Maximum

Minimum

121mm

152mm

Minimum

76mm

152mm

Minimum

Wall Mounted Object

Figure 4: Valance Install

Figure 5: Valance Iso View

Figure 6: Side Discharge

Figure 7: Side Discharge

Iso View

Figure 8: False Ceiling

Figure 9: False Ceiling

Iso View

Urbana U37 Installation guide

Urbana U37 Installation guide

Urbana U37 Installation guide

Other documents