2. ZKTeco
  3. Rots-3 Stand Wall Bracket

ZKTeco Rots-3 Stand Wall Bracket Installation guide

  • Hello! I've reviewed the Installation Guide for the ZKTeco Rots-3 Stand. This document provides detailed instructions on how to install the stand, mount compatible devices, and manage wiring. It includes information on adjustable angles, mounting hole options, and cable management. I am ready to answer any specific questions you may have about the installation process or compatible models such as ProFace X, SpeedFace V4L, SpeedFace V4LM1, SpeedFace V3L, SpeedFace V5/V5L, and Elite Series.
  • What is the recommended mounting height?
    How do I pass cables through the wire holes?
    What kind of screws used for mounting?
Installation Guide
Version: 1.0
Rots-3 Stand
Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between
the actual product and the written information in this manual.
1
Dimensions
2.559"(65.0mm)
1.772"(45.0mm)
Top View Bottom View
Side View
3.465"(88.0mm)
1.969"(50.0mm)
3.189"(81.0mm)
2.224"(56.5mm)
Wiring Hole
Wiring Hole
Wiring Hole
Wall Mounting Holes
Back Plate Mounting Holes
Adjustable Angle:
Vertical 20°
Horizontal 180°
Bottom Cover
Wiring Hole
Wiring Hole
Hexagon Socket
Screws
Adjusting Nut
Back Plate
Installation Diagram
2
Step 1: Remove the three screws from the bottom cover with a Phillips screwdriver.
Step 2: Remove the bottom cover.
Step 3: Pass the cables through the wire holes before you put the back plate on the base.
Step 4: Put the cable through the wire hole and then install the bottom cover agian with
the screws.
Note: The device has two wire holes, which users can choose according to their needs.
How to put the cables through the wire holes
Wiring Hole
1
3
24
3
Cable
How to install the mounting bracket on the wall?
Step 1: Drill four mounting holes at suitable locations on the wall. The recommended
height from the ground is 1.5 meters, which can be adjusted according to the actual
situation.
Step 2: Fix the mounting bracket on the wall using four wall mounting screws.
Percussion Drill Anchor
Screw
1
2
3
4
Note: The pictures in this manual are for reference only, please refer to the actual purchase.
How to connect the device with the mounting bracket?
Step 1: Pass the cables through the back plate.
Step 2: Identify the correct mounting holes and x the back plate on the mounting
bracket using the countersunk screws.
Step 3: Connect the cable to the device before attach the device to the back plate.
Step 4: Attach the device to the back plate with a security screw.
Step 5: Adjust the device to a suitable angle and lock the hexagonal screws on both sides.
Step 6: Install the bottom cover with the screws on the mounting bracket, as shown
in the gure below.
5
1
2
3
3
4
5
6
6
Back Plate
e.g. ProFace X
Mark the holes that can be used for installation
Mounting Hole Description for Compatible Models
Please choose dierent mounting holes for fastening the device according to the
back plate of compatible models as shown below:
Compatible models:
ProFaceX, SpeedFace V4L, SpeedFace V4LM1, SpeedFace V3L, SpeedFace V5/V5L,
Elite Series.
SpeedFace-V4L SpeedFace-V4LM1
Rots-3 Stand
Rots-3 Stand Rots-3 Stand
6
NOTE:
The location shown above is for reference only, choose the mounting holes based
on the physical object.
SpeedFace-V5/V5LSpeedFace-V3L
Elite Series
Rots-3 Stand Rots-3 Stand
Rots-3 Stand
7
Copyright © 2023 ZKTECO CO., LTD. All Rights Reserved.
ZKTeco Industrial Park, No. 32, Industrial Road,
Tangxia Town, Dongguan, China.
Phone : +86 769 - 82109991
Fax : +86 755 - 89602394
www.zkteco.com
/