Crawford 149194 User manual

Brand: Crawford

Model: 149194

Type: User manual

Crawford 149194: A versatile painter's putty for a variety of wood surfaces, both interior and exterior. Easily fills nail holes, cracks, and minor blemishes. Provides excellent adhesion, resists cracking, shrinking, and sagging. Water-based formula allows for easy cleanup and extended shelf life. Suitable for use on primed wood surfaces and requires priming on unpainted or new wood. Dries to a smooth, paintable finish, eliminating the need for sanding. Ideal for professional painters and DIY enthusiasts seeking a high-quality putty for their woodworking projects.

Putty Instructions

CRAWFORD’S NATURAL BLEND PAINTER’S PUTTY:

Crawford’s Natural Blend is a ready-to-use, multi-purpose painter’s putty for use

on old and new wood surfaces-inside or out. Select quality raw materials included

blended, all refined natural linseed oils (to help guard against bleeding), water-

ground calcium carbonates for product work-ability and paint grade titanium for

maximum brilliance. In a step taken long ago toward environmental awareness,

Crawford’s Natural Blend contains no white lead, asbestos or harsh chemical

preservatives. Crawford’s Natural Blend easily and quickly fills nail holes, counter

sunk primed nail heads, shallow hammer marks, small cracks and other minor

defacement’s on a variety of wood surfaces. Crawford’s Natural Blend exhibits

easy knifing; has excellent adherence to primed wood surfaces; resists cracking,

shrinking and sagging; and is packaged in water for extended shelf life.

Directions: Upon opening container pour off protective layer of water. Remove

amount of material needed. Dab dry excess moisture with cloth or rag. Important:

When not in use keep putty level in can and top again with ordinary tap water.

Place lid on tightly to keep material from drying inside container. On surface to be

puttied first remove all loose paint, splinters, dirt chalk, grease, etc. Sand any

glossy areas to help insure maximum adhesion. Dust the surface clean with a dry

paint brush. Use only on clean, dry and primed surfaces. New or unpainted wood

should be fully primed prior to use.

Roll putty with hand into the shape of a point then press firmly into holes with

thumb and forefinger. Holding a clean, dry putty knife in the opposite hand,

quickly cut off material in one motion. When properly performed the cut should

leave the patched area smooth and filled capacity thereby eliminating the need to

sand. Larger holes and cracks may require more than one application to obtain

this result. Once putty has been applied, allow it to form a protective surface skin

(top dry). For nail holes and other minor defacement’s this process takes

approximately 24 hours. Note: Top drying may be slowed by cold, damp weather

plus size and depth of fill. Also, do not touch putty once it has been placed in hole.

This action may break the thin surface membrane which has formed. (If applying

lacquer top coat or oxygen inhibitive coatings, putty should be allowed to dry and

minimum of 60 to 80 hours.) Once sufficient drying time has elapsed, prime and

paint-particularly when product is being used on exterior surfaces. Areas patched

which are going to be top coated with a gloss or semi-gloss paint should always be

sealed. Do not apply this product to any surface other than wood.

Note: It is the responsibility of the user to follow application instructions and to

propyl prepare surface prior to an after product application. Use is responsible for

determining if this product is suitable and fit for the application and substrate on

which it is intended to be applied.

Important: Keep out of the reach of children. Do not take internally. Wash hands

and tools with soapy water after each use. Protect from freezing. Do not thin with

any solvent. Do not add whiting. Replace water and keep lid on tightly when not

in use. Store in a cool place. Do not leave container exposed to direct sunlight for

prolonged periods of time. Do not apply in temperatures below 55 degrees F.

The manufacturer’s liability under any warranty, whether expressed or implied,

by contact or law, is hereby limited to replacement of this product. If found to be

defective upon inspection by CPC, Inc. In no case with CPC, Inc. reimburse or be

responsible for labor cost of the cost of the consequential damage in conjunction

with the use of this product. CPC, Inc. shall not be held liable for any

representations or claims made by its employees, agents, dealers or any

applicator. Other conditions also apply. Users are responsible to request,

understand and agree to these conditions prior to purchase or use of this product.

CPC, Inc.

Crawford’s For Today’s Professional Generation.

CRAWFORD PRODUCTS COMPANY, INC.

Montebello, California 90640 USA

Crawford 149194 User manual

Brand: Crawford

Model: 149194

Type: User manual

Download PDF

report

Crawford 149194 User manual

Crawford 149194 User manual

Other documents