Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comPage 4 DU-35AC Data Sheet (DU02)
96 mm
(3.78")
48 mm
(1.89")
3.9 mm
(0.15") typical
FRONT VIEW
1/8 DIN 96x48mm
These dimensions are
increased by 1.6mm (0.06")
when the metal surround
case is installed.
The 96x48mm case is
particularly suitable for
mounting in mosaic panels
or insulative panels up to 2"
thick. They can also stack
mount, 2 up in existing
cutouts for 1/4 DIN
(96x96mm) or 4 up in
1/2 DIN (96X192mm).
NOTE: The Metal Surround Case
is pre-installed at the factory and cannot
be removed without damage to the case.
Metal Surround Case
P/N:(OP-MTL96X48)
uses
Metal Screw Mount Clips
and has a max. panel
thickness mounting
of 15.5 mm (0.61").
Removable
Key-lock
Cam
Opening
Safety
Catch
Clear Lockable NEMA 4X
Splash Proof Cover
P/N:(OP-N4/96x48)
40.8 mm
(1.61")
117 mm
(4.61")
SIDE VIEW
5.3 mm
(0.21")
3.7mm
(0.15")
43.4 mm
(1.71")
DIN Cutout spacers
Straight-thru Connector for
meters with output board
20mm (0.79")
Right-angled Connector
11.8mm (0.47")
PANEL CUTOUT
Case will mount in standard 1/8 DIN cutouts
45 mm
(1.77")
Snug Fitting
Mosaic Fitting
92 mm
(3.62")
Loose Fitting
91.6mm
(3.6")
40.8mm
(1.61")
8 places
3mm
(0.12")
8 places
4mm
(0.16") 43.4mm
(1.71")
1/8 DIN
Cutout spacers
87.4mm
(3.45")
Various bezel
colors are available.
Black is standard.
For additional strength, extra Mounting
Slide Clips can be ordered and doubled up
one behind the other. P/N: (75-DMTCLIPF)
TOP VIEW
87.4mm
(3.45")
mosaic
fitting
95.4mm
(3.77")
Max. panel thickness
50mm
(1.97")
96 mm
(3.78")
91.6mm
(3.6")
DIN
Cutout
Spacer
To open rear cover,
use a small flat
bladescrew driver.
Press down lightly to
release catch on top
or bottom of case
and leaver outwards.
4.7mm
(0.19")
DIN Cutout Spacer
2mm
(0.08")
Connector
Socket
When extra panel
mounting tightness is
required, order the
optional screw mount clip.
P/N:(OP-MTLCLIP)
High Strength Panel
Mounting Kit
P/N: OP-PMA96X48
For extra strength in portable applications, the 8 DIN
spacers should be snipped off and the Mosaic fitting
cutout used. Alternatively, the High Strength Panel
Mounting Kit (Part # OP-PMA96X48) can be used.
Panel adaptor plates are
available to retrofit most
existing panel cutouts.
DU Case Dimensions and Panel Cutouts
Ordering Information
Standard Options for this Model Number
Part Number Description
BASIC MODEL NUMBER Includes plug in type screw terminals,
standard display and standard power supply unless optional versions
are ordered.
DU-35AC .........DPM, AC volts, Scaled RMS. 199.9/700V AC Selectable Ranges
DISPLAY
STANDARD.......Red LEDs, 0.56 inch high/C
DU-BRIGHT . . . . . . .Super bright Red LEDs, 0.56 inch high
DU-GREEN . . . . . . .Green LEDs, 0.56 inch high
DU-GREEN 4.5D . . .Dummy Zero Display Option w/ Green LEDs
DU-RED4.5D . . . . . .Dummy Zero Display Option w/ Green LEDs
DU-35HI/BRT . . . . . .Above center position, .56 inch, Bright Red LED
DU-35HI/GRN . . . . .Above center position, .56 inch, Green LED
DU-35HI/RED . . . . .Above center position, .56 inch, Red LED
POWER SUPPLY
STANDARD.......100/120 or 200/240VAC User selectable
V0-DC/ISO . . . . . . .Isolated auto-sensing AC/DC 9 to 36 VDC/12 to 24 VAC
V0-24V . . . . . . . . . .Isolated transformer 12 VAC or 24 VAC user selectable
SPECIAL OPTIONS
(Specify Inputs or Outputs & Req. Reading
)
HD-CHANGE . . . . . . . . .Range change from the standard input as shown in BOLD type
V0-50K . . . . . . . . . .Zero offset potentiometer 50k
CB-FS35 . . . . . . . . .Non-Std Range and Scale Changes for all DU-35 series
Special Options and Accessories
Part Number Description
ACCESSORIES
(Specify Serial # for Custom Artwork Installation)
75-DBBZ9648F . . . .Black Bezel for 96x48mm Case
75-DMTCLIPF . . . . .Side Slide Brackets (2 pc) - extra set, extra strength
76-DU35G . . . . . . . .Replacement DU Series grey lens for Green LEDs
76-DU35R . . . . . . . .Replacement DU Series red lens for Red LEDs
76-DUPP/N . . . . . . .Anti-glare protective front lens plate for DU Series
93-PLUG2P-DP . . . .Extra Screw Terminal Conn., 2 Pin Power Plug
93-PLUG3P-DR . . . .Extra Screw Terminal Conn., 3 Pin Plug
CN-SPADE . . . . . . . .Spade Lug pinouts and Insulated quick disconnects
DN•CAS96X48A . . .Complete 96x48mm Case with bezel
OP-DUEXTDP . . . . .Option for External Decimal Point
OP-MCLP96X48 . . .Screw Mounting Clips (2 pc) to screw tighten slide brackets
OP-MTL96X48 . . . . .Metal Surround Case includes metal mounting clips
OP-N4X/96X48 . . . .Clear Lockable Water-proof cover, Nema 4X, IP65
QD-KIT-1 . . . . . . . . .Replacement Crimp-on Quick Disconnects (7 per Set)
ART-FS-S/D . . . . . . .NRC for Artwork & set-up Custom Faceplate and or Descriptor
ART-FS-S/D/C . . . . . . . .NRC for Artwork & set-up Custom Faceplate and Custom Logo
ART-FS-001 . . . . . . . . . .Produce & Install Custom Faceplate per meter - 1 color no-min
ART-FS-002 . . . . . . . . . .Produce & Install Custom Faceplate per meter - 2 color no-min
ART-FS-003 . . . . . . . . . .Produce & Install Custom Faceplate per meter - 3 color no-min
ART-FL-001 . . . . . . . . . .Custom Faceplate, 250 piece Min. - 1 color
ART-FL-002 . . . . . . . . . .Custom Faceplate, 250 piece Min. - 2 color
ART-FL-003 . . . . . . . . . .Custom Faceplate, 250 piece Min. - 3 color
Many other options and accessories are available. See full price list for more details.
Prices subject to change without notice.
WARRANTY
Texmate warrants that its products are free from defects in material and workmanship under
normal use and service for a period of one year from date of shipment. Texmate’s obligations
under this warranty are limited to replacement or repair, at its option, at its factory, of any of the
products which shall, within the applicable period after shipment, be returned to Texmate’s facil-
ity, transportation charges pre-paid, and which are, after examination, disclosed to the satis-
faction of Texmate to be thus defective. The warranty shall not apply to any equipment which
shall have been repaired or altered, except by Texmate, or which shall have been subjected to
misuse, negligence, or accident. In no case shall Texmate’s liability exceed the original pur-
chase price. The aforementioned provisions do not extend the original warranty period of any
product which has been either repaired or replaced by Texmate.
USER’S RESPONSIBILITY
We are pleased to offer suggestions on the use of our various products either by way of print-
ed matter or through direct contact with our sales/application engineering staff. However, since
we have no control over the use of our products once they are shipped, NO WARRANTY
WHETHER OF MERCHANTABILITY, FITNESS FOR PURPOSE, OR OTHERWISE is made
beyond the repair, replacement, or refund of purchase price at the sole discretion of Texmate.
Users shall determine the suitability of the product for the intended application before using,
and the users assume all risk and liability whatsoever in connection therewith, regardless of any
of our suggestions or statements as to application or construction. In no event shall Texmate’s
liability, in law or otherwise, be in excess of the purchase price of the product.
Texmate cannot assume responsibility for any circuitry described. No circuit patent or software
licenses are implied. Texmate reserves the right to change circuitry, operating software, speci-
fications, and prices without notice at any time.
For product details visit www.texmate.com
Local Distributor Address
995 Park Center Drive • Vista, CA 92081-8397
Tel: 1-760-598-9899 • USA 1-800-839-6283 • That’s 1-800-TEXMATE
Fax: 1-760-598-9828 • Email: sales@texmate.com • Web: www.texmate.com
Texmate has facilities in Japan, New Zealand, Taiwan, and Thailand. We also have
authorized distributors throughout the USA and in 28 other countries.
Copyright © 2004 Texmate Inc. All Rights Reserved.