Cameo ZENIT® W300 User manual

ZENIT® W300

LED OUTDOOR WASHLIGHT

CLZW300

USER´S MANUAL

BEDIENUNGSANLEITUNG

MANUEL D`UTILISATION

MANUAL DE USUARIO

INSTRUKCJA OBSŁUGI

MANUALE D‘ USO

iDMX® APP

CONTROL

SNAPMAG®

TECHNOLOGY

MULTIPLE

ANGLES

FIRMWARE VERSION 1.80 AND HIGHER

CONTENTS / INHALTSVERZEICHNIS / CONTENU /

CONTENIDO / TREŚĆ / CONTENUTO

ENGLISH

INFORMATION ON THIS USER MANUAL 6

INTENDED USE 6

DEFINITIONS AND SYMBOL EXPLANATIONS 6

SAFETY INSTRUCTIONS 7

NOTES ON PORTABLE OUTDOOR DEVICES 12

SCOPE OF DELIVERY 12

INTRODUCTION 13

CONNECTIONS, OPERATING AND DISPLAY ELEMENTS 13

OPERATION 15

IR REMOTE CONTROL 25

SETUP AND INSTALLATION 26

CARE, MAINTENANCE AND REPAIR 26

OPTIONAL ACCESSORIES 28

DMX TECHNOLOGY 29

TECHNICAL DATA 31

EXPLANATION OF IP PROTECTION CLASS 33

MINIMUM DISTANCE TO ILLUMINATED SURFACE 33

MINIMUM DISTANCE TO NORMALLY FLAMMABLE MATERIALS 33

DISPOSAL 34

MANUFACTURER’S DECLARATIONS 34

DEUTSCH

INFORMATIONEN ZU DIESER BEDIENUNGSANLEITUNG 37

BESTIMMUNGSGEMÄSSER GEBRAUCH 37

BEGRIFFS- UND SYMBOLERKLÄRUNGEN 37

SICHERHEITSHINWEISE 38

HINWEISE FÜR ORTSVERÄNDERLICHE OUTDOOR-GERÄTE 44

LIEFERUMFANG 44

EINFÜHRUNG 44

ANSCHLÜSSE, BEDIEN- UND ANZEIGEELEMENTE 45

BEDIENUNG 47

IR FERNBEDIENUNG 57

AUFSTELLUNG UND MONTAGE 58

PFLEGE, WARTUNG UND REPARATUR 58

OPTIONALES ZUBEHÖR 60

DMX TECHNIK 61

TECHNISCHE DATEN 63

IP-SCHUTZART 65

MINDESTABSTAND ZUR BELEUCHTETEN FLÄCHE 65

MINDESTABSTAND ZU NORMAL ENTFLAMMBAREN MATERIALIEN 65

ENTSORGUNG 66

HERSTELLERERKLÄRUNGEN 67

FRANCAIS

INFORMATIONS CONCERNANT CE MANUEL D’UTILISATION 68

UTILISATION CONFORME 68

EXPLICATIONS DES TERMES ET DES SYMBOLES 68

CONSIGNES DE SÉCURITÉ 69

REMARQUES CONCERNANT LES APPAREILS D’EXTÉRIEUR MOBILES 75

CONTENU DE LA LIVRAISON 75

INTRODUCTION 76

RACCORDEMENTS, ÉLÉMENTS DE COMMANDE ET D’AFFICHAGE 76

UTILISATION 79

TÉLÉCOMMANDE INFRAROUGE 89

INSTALLATION ET MONTAGE 90

ENTRETIEN, MAINTENANCE ET RÉPARATION 91

ACCESSOIRES DISPONIBLES EN OPTION 93

TECHNIQUE DMX 94

CARACTÉRISTIQUES TECHNIQUES 96

EXPLICATIONS RELATIVES À L’INDICE DE PROTECTIONIP 98

DISTANCE MINIMALE PAR RAPPORT À LA SURFACE ÉCLAIRÉE 98

DISTANCE MINIMALE PAR RAPPORT AUX MATÉRIAUX NORMALEMENT INFLAMMABLES 98

ÉLIMINATION 99

DÉCLARATIONS DU FABRICANT 100

ESPAÑOL

INFORMACIÓN SOBRE ESTE MANUAL DE INSTRUCCIONES 101

USO PREVISTO 101

TÉRMINOS Y SÍMBOLOS 101

INSTRUCCIONES DE SEGURIDAD 102

INDICACIONES PARA EQUIPOS PORTÁTILES DE EXTERIOR 108

VOLUMEN DE SUMINISTRO 108

INTRODUCCIÓN 108

CONEXIONES, ELEMENTOS DE MANEJO Y ELEMENTOS DE VISUALIZACIÓN 109

FUNCIONAMIENTO 111

MANDO A DISTANCIA POR INFRARROJOS 122

INSTALACIÓN Y MONTAJE 123

CUIDADO, MANTENIMIENTO Y REPARACIÓN 124

ACCESORIOS OPCIONALES 126

TECNOLOGÍA DMX 127

DATOS TÉCNICOS 129

EXPLICACIÓN SOBRE LA CLASE DE PROTECCIÓN IP 131

DISTANCIA MÍNIMA CON RESPECTO A LA SUPERFICIE ILUMINADA 131

DISTANCIA MÍNIMA CON RESPECTO A MATERIALES NORMALMENTE INFLAMABLES 131

ELIMINACIÓN 132

DECLARACIONES DEL FABRICANTE 133

POLSKI

INFORMACJE DOTYCZĄCE NINIEJSZEJ INSTRUKCJI OBSŁUGI 134

UŻYTKOWANIE ZGODNE Z PRZEZNACZENIEM 134

OBJAŚNIENIA TERMINÓW I SYMBOLI 134

ZASADY BEZPIECZEŃSTWA 135

UWAGI DOTYCZĄCE PRZENOŚNEGO SPRZĘTU ZEWNĘTRZNEGO 141

ZAKRES DOSTAWY 141

WPROWADZENIE 142

GNIAZDA, ELEMENTY OBSŁUGI I WSKAŹNIKI 142

OBSŁUGA 145

PILOT NA PODCZERWIEŃ 155

USTAWIANIE I MONTAŻ 156

CZYSZCZENIE, KONSERWACJA I NAPRAWY 156

OPCJONALNE AKCESORIA 158

TECHNIKA DMX 159

DANE TECHNICZNE 161

OBJAŚNIENIA DOTYCZĄCE STOPNIA OCHRONY IP 163

MINIMALNA ODLEGŁOŚĆ OD POWIERZCHNI OŚWIETLONEJ 163

MINIMALNA ODLEGŁOŚĆ OD NORMALNIE ŁATWOPALNYCH MATERIAŁÓW 163

UTYLIZACJA 164

OŚWIADCZENIA PRODUCENTA 165

CONTENTS / INHALTSVERZEICHNIS / CONTENU /

CONTENIDO / TREŚĆ / CONTENUTO

ITALIANO

INFORMAZIONI SUL PRESENTE MANUALE D’USO 166

UTILIZZO CONFORME 166

SPIEGAZIONE DI CONCETTI E SIMBOLI 166

INDICAZIONI SULLA SICUREZZA 167

AVVERTENZE PER DISPOSITIVI PORTATILI PER ESTERNI 173

VOLUME DI CONSEGNA 173

INTRODUZIONE 173

CONNETTORI, ELEMENTI DI COMANDO E VISUALIZZAZIONE 174

UTILIZZO 176

TELECOMANDO A INFRAROSSI 187

INSTALLAZIONE E MONTAGGIO 188

PULIZIA, MANUTENZIONE E RIPARAZIONE 188

ACCESSORI OPZIONALI 190

TECNOLOGIA DMX 191

DATI TECNICI 193

SPIEGAZIONI SULLA PROTEZIONE IP 195

DISTANZA MINIMA DALLA SUPERFICIE ILLUMINATA 195

DISTANZA MINIMA DAI MATERIALI NORMALMENTE INFIAMMABILI 195

SMALTIMENTO 196

DICHIARAZIONI DEL PRODUTTORE 197

DMX

DMX CONTROL / DMX STEUERUNG / PILOTAGE DMX /

CONTROL DMX / STEROWANIE DMX / CONTROLLO DMX 198

6

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

ENGLISH

YOU‘VE MADE THE RIGHT CHOICE!

We have designed this product to operate reliably over many years. Please read this User‘s

Manual carefully, so that you can begin making optimum use of your Cameo Light product

quickly. Learn more about Cameo Light on our website WWW.CAMEOLIGHT.COM.

INFORMATION ON THIS USER MANUAL

• Carefully read the safety instructions and the entire manual before operating the device.

• Observe the warnings on the device and in the user manual.

• Always keep the user manual within reach.

• If you sell or pass on the device, it is important that you also include this user manual, as it is an

integral part of the product.

INTENDED USE

The product is a device for event technology!

This product has been developed for professional use in the ﬁeld of event technology and is not

suitable for use as domestic lighting!

Furthermore, this product is only intended for qualiﬁed users with specialist knowledge of event

technology!

Use of the product outside the speciﬁed technical data and operating conditions is considered

inappropriate!

Liability for damage and third-party damage to persons and property due to inappropriate use is

excluded!

The product is not suitable for:

• Use by persons (including children) with limited physical, sensory or mental abilities or lack of

experience and knowledge.

• children (children must be instructed not to play with the device).

DEFINITIONS AND SYMBOL EXPLANATIONS

1. HAZARD: The word HAZARD, possibly in combination with a symbol, indicates situations in

which there is an immediate danger or risk of potentially fatal injury.

2. WARNING: The word WARNING, possibly in combination with a symbol, indicates situations in

which there is an immediate danger or risk of potentially fatal injury.

3. CAUTION: The word CAUTION, possibly in combination with a symbol, indicates situations or

conditions that could result in injury.

4. ATTENTION: The word ATTENTION, possibly in combination with a symbol, indicates situations

or conditions that could result in damage to property and/or the environment.

7

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

This symbol identifies hazards that can cause electric shock.

This symbol identifies hazardous areas or hazardous situations.

This symbol indicates hazards caused by hot surfaces.

This symbol indicates hazards caused by intense light sources.

This symbol indicates a device in which there are no user-replaceable parts.

This symbol indicates additional information on the operation of the product.

SAFETY INSTRUCTIONS

HAZARD:

1. Do not open the device and do not perform any modiﬁcations.

2. If your device no longer functions properly, if liquids or objects get inside it or if it

has been damaged in any other way, switch it off immediately and unplug it from

the power source. The device may be repaired only by authorised repair techni-

cians.

3. For devices of protection class 1, the protective conductor must be connected

correctly. Never disconnect the protective conductor. Devices of protection class 2

do not have a protective conductor.

4. Ensure that live cables are not kinked or otherwise mechanically damaged.

5. Never bypass the device fuse.

WARNING:

1. The device may not be operated if it shows obvious signs of damage.

2. The device may only be installed in a voltage-free state.

3. If the device's power cable is damaged, the device may not be used.

4. Permanently connected power cables may only be replaced by a qualified person.

8

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

ATTENTION:

1. Do not switch on the device if it has been exposed to extreme temperature ﬂuctu-

ations (for example, following transport). Moisture and condensation can damage

the device. Switch on the device only when it has reached room temperature.

2. Ensure that the voltage and frequency of the mains supply match the values spec-

iﬁed on the device. If the device has a voltage selector switch, do not connect the

device until it has been set correctly. Use only suitable power cables.

3. To disconnect the device from the mains on all poles, it is not sufﬁcient to press the

on/off switch on the device.

4. Make sure that the fuse used corresponds to the type printed on the device.

5. Ensure that suitable measures have been taken against overvoltage (e.g. lightning

strikes).

6. Observe the speciﬁed maximum output current on devices with a Power Out con-

nection. Ensure that the total current consumption of all connected devices does

not exceed the speciﬁed value.

7. Replace plug-in power cables with original cables only.

HAZARD:

1. Choking hazard! Plastic bags and small parts must be kept out of reach of persons

(including children) with reduced physical, sensory or mental capabilities.

2. Risk of falling! Make sure that the device is securely installed and will not fall

down. Only use suitable stands or mounts (particularly for ﬁxed installations).

Ensure that accessories are properly installed and secured. Ensure that applicable

safety regulations are observed.

WARNING:

1. Use the device in the prescribed manner only.

2. Operate the device using only accessories of the type recommended and supplied

by the manufacturer.

3. Observe safety regulations applicable in your country during installation.

4. After connecting the device, ensure that all cables are routed so as to avoid dam-

age or accidents, such as from tripping.

5. Always observe the speciﬁed minimum distance to normally ﬂammable materials!

Unless explicitly stated, the minimum distance is 0.3 m.

6. Always observe the minimum distance to the illuminated surface, which can be

read on the device!

9

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

CAUTION:

1. Moving components such as mounting brackets may become jammed.

2. In the case of devices with motor-driven components, there is a risk of injury due

to the movement of the device. Sudden movement of the device can cause shock

reactions.

3. The housing surface of the device can become very hot during regular operation.

Ensure that accidental touching of the housing is not possible. Always allow the

device to cool sufﬁciently before removal, maintenance work and charging etc.

ATTENTION:

1. Do not install or use the device in the vicinity of radiators, accumulators, stoves, or

other heat sources. Ensure that the device is always installed in such a way that it

is sufﬁciently cooled and cannot overheat.

2. Do not place any ignition sources, such as burning candles, near the device.

3. Ventilation openings must not be covered and fans must not be blocked.

4. For transport, use the original packaging or packaging provided by the

manufacturer.

5. Avoid any impacts to or shaking of the device.

6. Observe the IP rating and the ambient conditions such as temperature and humidi-

ty according to the speciﬁcations.

7. Devices can be continuously further developed. In the event of deviating informa-

tion on operating conditions, performance or other device properties between the

user manual and the device labelling, the information on the device always has

priority.

8. The device is not suitable for tropical climate zones or for operation over 2,000 m

above sea level.

9. Unless explicitly stated, the device is not suitable for operation under marine

conditions.

NOTE:

In the case of conversion or retrofit sets or accessories provided by the manufacturer,

be sure to observe the enclosed instructions.

CAUTION! IMPORTANT INFORMATION REGARDING LIGHTING PRODUCTS!

1. Never look directly into the beam of light, not even for a short period of time.

2. Never look into the beam of light using optical devices such as a magnifying glass.

3. Stroboscopic effects may cause epileptic seizures in susceptible individuals!

10

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

4. These luminaires contain permanently installed light sources which cannot be

replaced by the user. The light source contained in this luminaire may only be

replaced by the manufacturer or its service partner or a similarly qualified person.

SIGNAL TRANSMISSION AND CONTROL BY RADIO

(e.g. W-DMX or audio radio systems, Bluetooth):

The quality and performance of wireless signal transmissions generally depends on

the ambient conditions.

The following factors can impact range and signal stability, for example:

• Shielding (e.g. masonry, metal structures, water)

• High volume of radio trafﬁc (e.g. powerful wireless LAN networks)

• Interference

• Electromagnetic radiation (e.g. LED video screens, dimmers)

All range speciﬁcations refer to free-ﬁeld application with visual contact and without

interference!

The operation of transmission systems is subject to ofﬁcial regulations. These may

vary from region to region and must be checked by the operator before use (e.g. radio

frequency and transmission power).

WARNING: Devices with wireless signal transmission are not suitable for use in sen-

sitive areas in which radio operation can lead to potential detrimental effects. These

include:

• Hospitals, health centres or other healthcare facilities that provide patient treatment

with skilled personnel and equipment.

• Hazardous areas Class I, II and III

• Restricted areas

• Military facilities

• Aircraft or vehicles

• Areas where the use of mobile phones is prohibited

11

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

TRANSMISSION VIA W-DMX

WARNING: In general, wireless DMX transmission must not be used for applications

involving safety-related factors that might result in personal injury or property dam-

age in the event of a failure.

This applies in particular to moving scene or traverse structures, DMX-controlled

motors/lifts or lifting devices for operating DMX-operated platform lifts, hydraulic

systems or comparable moving components.

Furthermore, wireless DMX transmission must not be used to trigger ﬂame or pyro-

technic devices, explosion-driven effects, or to control gas or liquid effects. These

include CO2 cannons, confetti shooters, water effects or similar.

DEVICES WITH BATTERY OR ACCUMULATOR REPLACEMENT PROVIDED BY THE

USER (e.g. remote control)

DANGER:

Be sure to observe the manufacturer's data sheet for the batteries or

rechargeable batteries used!

1. Batteries and rechargeable batteries must be kept out of reach of persons

(including children) with reduced physical, sensory or mental capabilities. Danger

of suffocation!

2. Avoid strong mechanical impacts on batteries and accumulators! Damage due to

falling, smashing or puncturing as well as high pressure leads to fire and explosion

hazards as well as the risk of further dangerous situations (e.g. outgassing).

3. Leaking battery fluid is corrosive and can be toxic. It can cause skin and eye

irritation and is dangerous if swallowed. Avoid any contact with leaked fluid. In

case of contact with leaked liquid, wash the affected area immediately with plenty

of water and contact a doctor.

4. Never attempt to charge non-rechargeable batteries. Danger of explosion!

5. Do not throw batteries and rechargeable batteries into a fire! Danger of explosion!

6. Do not short-circuit batteries and rechargeable batteries! Avoid contact of the

battery terminals with electrically conductive objects (e.g. key ring or coins).

12

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

ATTENTION:

1. When inserting batteries and rechargeable batteries, ensure that the polarity is

correct (see illustrations in the battery compartment or on the housing).

2. Do not use different cell types and battery brands in the same unit at the same

time.

3. Only use batteries and rechargeable batteries with the same discharge status.

4. Check batteries and rechargeable batteries for damage and do not use damaged

batteries and rechargeable batteries!

NOTES ON PORTABLE OUTDOOR DEVICES

1. Temporary operation! Event equipment is generally only designed for temporary

operation.

2. Continuous operation or permanent structural installation – particularly outdoors –

can impair the function, surfaces and seals and accelerate material fatigue.

3. Damage to the surface coating can impair the device's corrosion protection.

Damaged surface coating (e.g. scratches) must be promptly repaired by suitable

measures.

SCOPE OF DELIVERY

Remove the product from the packaging and remove all packaging material.

Please check the completeness and integrity of the delivery and notify your distribution partner

immediately after purchase if the delivery is not complete or if it is damaged.

Product includes:

• Headlights

• Mains cable

• 1x Omega bracket

• IR remote control

• Operating instructions

13

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

INTRODUCTION

LED WASH LIGHT 300 W RGBW IP65

CLZW300

CONTROL FUNCTIONS:

2-channel CCT, 3-channel color macros, 3-channel RGB 8-bit, 4-channel RGBW 8-bit, 6-channel

RGB 16-bit, 8-channel RGBW 8 Bit, 8-channel RGBW 16-bit, 10-channel full-access 8-bit, and

15-channel full-access 16-bit DMX controll

Master/Slave operation

Standalone functions

W-DMX™

IR remote control

FEATURES:

DMX-512. 21 x 15 W High Power RGBW LEDs. W-DMX™. IR remote control included. Strobe.

16-bit dimmer. 4 dimmer curves. Color temperature correction. Adjustable LED PWM frequency.

Fast Access Feature. IP65-rated. IP65 5-pin DMX ports. Plastic feet. Omega mounting bracket

included. Operating voltage 100–240 V AC. Power consumption 300W. 25°, 45°, 60° x 10°, 100°

diffusers and barn-door available as an option. The spotlight features the RDM standard (Remote

Device Management). This remote device management system makes it possible to carry out

status checks and configure RDM devices with an RDM-enabled controller.

CONNECTIONS, OPERATING AND DISPLAY ELEMENTS

134

56 6

2

1 POWER IN

IP65 power input socket with rubber sealing cap. Operating voltage 100-240 V AC/50-60 Hz.

Connection via included power cable (when not in use, always close with rubber sealing cap).

14

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

2 POWER OUT

IP65 power output socket with rubber sealing cap. Facilitates power supply to other CAMEO

spotlights. Ensure that the total current consumption of all connected devices does not exceed

the value specified on the device in amperes (A) (when not in use, always close with the rubber

sealing cap).

3 DMX IN

Male IP65 5-pin XLR socket for connecting a DMX control device (e.g. DMX console; when not in

use, always close with the rubber sealing cap).

4 DMX OUT

Female IP65 5-pin XLR socket for sending DMX control signal (when not in use, always close with

the rubber sealing cap).

5 OLED-DISPLAY

Displays the current operating mode and other system settings.

6 TOUCH-SENSITIVE CONTROLS

MODE

Press MODE to access the selection menu for system settings. Press repeatedly to go back to the

main display.

ENTER

Press ENTER to access the menu levels to make value changes, and to access the sub-menus.

Confirm changes by pressing ENTER.

UP and DOWN

Select individual menu items in the selection menu (DMX address, operating mode etc.) and in the

sub-menus. Allow changes to the value of a menu item, such as the DMX address as required.

PRESSURE EQUALISATION ELEMENT

The pressure equalisation element to prevent condensation inside the housing is in the device

base, behind the cable feed for the LED unit. In order to ensure its proper function, the element

must be protected from contamination.

HOUSING FAN

The 3 housing fans and the heat sink are on the back of the LED unit. Ensure air circulation by not

covering the device, and cleaning it regularly.

15

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

NOTES: In order to provide protection from spraying water, in accordance with protection class

IP65, special IP65-rated XLR connectors must be used correctly with the DMX input and output

sockets, or they must be closed using the rubber sealing caps. When connected correctly, or

when sealed correctly with the rubber sealing caps, the POWER IN and POWER OUT sockets are

protected from spraying water, as in accordance with IP65.

PLEASE NOTE

As soon as the spotlight is correctly connected to the power supply, the following will be displayed

in succession during the starting process: “Welcome to Cameo”, the model name and the soft-

ware version. After this process, the spotlight is ready for operation, and starts in the previously

enabled mode.

• If one of the DMX operating modes is activated and there is no DMX signal to the DMX input, the

currently programmed DMX address is displayed and the characters on the display will begin to

ﬂash.

• After approximately 1 minute of inactivity, the display will automatically show the currently

active operating mode.

• Fast Access Feature: In order to simplify the menu guide, the device has an intelligent menu

structure that allows direct access to previously selected menu items and sub-menu items.

1. Press MODE and ENTER simultaneously for direct access to the last-edited sub-menu item,

where you can make changes instantly as required (DMX starting address and all modes).

2. Press MODE for direct access to the last-selected and last-edited menu item. Press ENTER

repeatedly to access the sub-menu items in order to change individual settings (DMX start-

ing address and all modes).

• Before changing device settings, ensure that the control panel is dry and dust free so that its

functionality is not impaired.

• The display can be rotated 180° by pressing UP when the main display is visible.

OPERATION

MAIN DISPLAY

After the power-up process, the lamp is ready for operation and starts in the previously activated

mode. The main display appears with the following information: Current mode (in the example

DMX mode) and W-DMX™ status.

DMX Address

001

W-DMX™ status

Current operating mode

16

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

W-DMX™

1. To pair with W-DMX™ compatible transmitters, enable W-DMX™ in the device settings (Set-

tings -> Wireless Setting -> W-DMX On Off -> On) and reset the W-DMX™ module (Receive Re-

set -> Yes). Start the pairing process as described in the operating instructions of the W-DMX™

transmitter. Pairing is then completed automatically.

2. Connect a group of W-DMX™ devices to create a DMX universe. Disconnect all devices that

are supposed to form the group (Settings -> Wireless Setting -> Receive Reset). Now activate

a CLZW300 with a DMX controller via DMX cable and in the settings, select “Transmit” (Send)

(Settings -> Wireless Setting -> Operating Mode -> Transmit). In the settings of the W-DMX™

devices to be controlled via W-DMX™, select “Receive” (Settings -> Wireless Setting -> Operat-

ing Mode -> Receive), pair them and conﬁrm by selecting “Link” (Settings -> Wireless Setting ->

Link -> Link) in the settings of the CLZW300 controlled via DMX cable. Pairing is then completed

automatically.

3. It is also possible to create a networked group of W-DMX™ devices via W-DMX™ and to oper-

ate them in master/slave mode to use. Disconnect all devices that are supposed to form the group

(Settings -> Wireless Setting -> Receive Reset). Now, in the settings (Settings -> Wireless Setting

-> Operating Mode) of the master unit select “Transmit” (send) and in the settings of the select-

ed slave units, select “Receive”. In the master unit, select the entry “Link” (Settings -> Wireless

Setting -> Link -> Link) and conﬁrm by pressing ENTER. Pairing of the devices is then completed

automatically. In the master unit, select one of the standalone modes (Auto, Color Macro, Static,

Tunable White, User Color) and control the slave units with it.

W-DMX™ STATUS

G3 G4S

W-DMX™

deactivated

W-DMX™

activated as

receiver,

not paired

W-DMX™

activated as

receiver and

is coupled to

device,

Transmitter is

switched off or

out of range

W-DMX

activated and

is coupled to

device,

no DMX signal

W-DMX™

activated as

receiver and

is coupled to

device,

DMX signal is

present

W-DMX™ and

transmission

mode G3 is

enabled

Up arrow =

Send operation

Arrow Down

= Receive

operation

Arrow ﬂashes=

pairing process

Flashing stops =

paired

W-DMX™ and

transmission

mode G4S is

enabled

Up arrow =

Send operation

Arrow Down

= Receive

operation

Arrow ﬂashes=

pairing process

Flashing stops =

paired

17

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

SETTING DMX START ADDRESS (DMX Address)

Press MODE to access the selection menu. Using the UP and DOWN controls, select the menu

item “DMX address” (observe arrow) and conﬁrm with ENTER. The display will show a three-digit

number ﬁeld and you can use the UP and DOWN controls to conﬁgure the desired DMX start

address. Conﬁrm the entry with ENTER and press MODE to return to the main display (in the

example, “DMX address 001”).

---------------- Menu ----------------

DMX Address

DMX mode

Stand Alone

Slave

Settings

System Info

DMX Address

001

5xx

–

CONFIGURING DMX MODE (DMX Mode)

Press MODE to access the selection menu. Using the UP and DOWN controls, select the menu

item “DMX Mode” (observe arrow) and conﬁrm with ENTER. In the sub-menu, you can now select

between 9 different DMX operating modes with the UP and DOWN buttons. Conﬁrm your selection

with ENTER. Tables with the channel assignments can be found in these instructions under DMX

CONTROL.

---------------- Menu ----------------

DMX Address

DMX Mode

Stand Alone

Slave

Settings

System Info

------------ DMX MODE ------------

15CH Full Access

10CH Full Access

8CH 8Bit

8CH User-Calibrated

6CH Factory-Calibrated

4CH User-Calibrated

3CH Factory-Calibrated

3CH Color Macro

2CH CCT Factory-Calib

SETTING STANDALONE MODE

Press MODE to access the selection menu. Use UP and DOWN to select the menu item “Stand

Alone” (observe arrow) and conﬁrm with ENTER. In the sub-menu you can now select from the

standalone modes “Auto”, “Colour Macro”, “Static”, “Tunable White” and “User Colour” as well as

the timer function “Timer” using UP and DOWN. Conﬁrm your selection with ENTER.

---------------- Menu ----------------

DMX Address

DMX mode

Stand Alone

Slave

Settings

System Info

------------ Stand Alone -----------

Auto

Color Macro

Static

Tunable White

User Color

Timer

18

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

AUTO MODE (programme 1 – programme 6)

The 6 different auto-programmes each comprise non-editable color-change sequences. Bright-

ness and speed are independently adjustable. Select auto mode as per the procedure previously

described in SETTING STAND ALONE MODE and conﬁrm with ENTER. Using the UP and DOWN

controls, now select one of the 6 auto-programmes (observe arrow) and conﬁrm with ENTER. To

adjust brightness, use the UP and DOWN controls to select the menu item “Dim”, and conﬁrm

with ENTER, then use the UP and DOWN controls to select the desired value between 000 and

255. Conﬁrm with ENTER. Set the run speed by selecting the menu item “Speed”, conﬁrm with

ENTER, and then select the desired value between 001 and 100. Conﬁrm with ENTER. Press

MODE four times to return to the main display (Mode Auto).

000

255

–

Dim

001

100

–

Speed

----------- Stand Alone -----------

Auto

Color Macro

Static

Tunable White

User Color

Timer

Mode

Auto

---------------- Auto ----------------

Program 1

Program 2

Program 3

Program 4

Program 5

Program 6

----------- Programme x -----------

Dim <255>

Speed <100>

001

100

–

COLOR MACROS (Color Macro)

15 different preset color macros are available. Select color macro mode as per the procedure pre-

viously described in SETTING OPERATION MODE and conﬁrm with ENTER. Using the UP and DOWN

controls, now select the desired color preset (observe arrow) and conﬁrm with ENTER (Color Off

= blackout). The display will show a three-digit number ﬁeld and you can use the UP and DOWN

controls to set the desired brightness between 000 and 100. Conﬁrm with ENTER. Press MODE

three times to return to the main display (color macro mode).

Mode

Color Macro

---------- Color Macro ----------

Color O

Red <100>

Amber <100>

Yellow Warm <100>

Yellow <100>

Green <100>

Turquoise <100>

Cyan <100>

Blue <100>

Lavender <100>

Mauve <100>

Magenta <100>

Pink <100>

Warm White <100>

White <100>

Cold White <100>

----------- Stand Alone -----------

Auto

Color Macro

Static

Tunable White

User Color

Timer

000

100

–

STATIC MODE (Static)

The static mode allows the Dimmer, Strobe, R, G, B, W to be adjusted directly on the device with

values between 000 and 255, in a similar way to with a DMX controller. In this way, an individual

scene can be created without an additional DMX controller. Select static mode as per the proce-

dure previously described in SETTING OPERATION MODE and conﬁrm with ENTER. Using the UP

and DOWN controls, now select the menu item that you wish to edit (observe arrow) and conﬁrm

with ENTER. The display will show a three-digit number ﬁeld and you can use the UP and DOWN

controls to conﬁgure the desired value between 000 and 255. Conﬁrm with ENTER. Press MODE

three times to return to the main display (static mode).

19

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

Mode

Static

---------------- Static ----------------

Dimmer <255>

Strobe <255>

Red <255>

Green <255>

Blue <255>

White <255>

000

255

–

----------- Stand Alone -----------

Auto

Color Macro

Static

Tunable White

User Color

Timer

COLOR TEMPERATURE (Tunable White)

The color temperature mode enables you to conﬁgure the color temperature from warm white to

cold white (CCT) and the brightness (Dim) of the light directly on the device. Select the color tem-

perature mode as per the procedure previously described in SETTING STAND ALONE MODE and

conﬁrm with ENTER. Using the UP and DOWN controls, now select the menu item that you wish to

edit (observe arrow) and conﬁrm with ENTER. The display will show a three-digit number ﬁeld and

you can use the UP and DOWN controls to conﬁgure the desired value. Conﬁrm with ENTER. Press

MODE three times to return to the main display (Mode Tunable White).

----------- Stand Alone -----------

Auto

Color Macro

Static

Tunable White

User Color

Timer

Mode

Tunable White

000

100

–

Dim

000

255

–

CCT

---------- Programme x ----------

Dim <100>

CCT <255>

USER PRESETS (User color)

The operating mode “User Presets” allows you to store ﬁve individual color presets of overall

brightness, strobe and a color mix of R, G, B and W directly in the device. Select the “User Color”

mode as per the procedure previously described in SETTING STAND ALONE MODE and conﬁrm

with ENTER. Use UP AND DOWN to select one of the stored presets Color1 to Color5 and conﬁrm

with ENTER and select the submenu item you want to edit (see arrows). Conﬁrm with ENTER.

The display will show a three-digit number ﬁeld and you can use the UP and DOWN controls to set

the value as required between 000 and 255. Conﬁrm by pressing ENTER again. When all settings

are conﬁgured as required, press MODE 4 times to return to the main display (Mode User Color).

Mode

User Color

------------ User Color ------------

Color1

Color2

Color3

Color4

Color5

----------- Stand Alone -----------

Auto

Color Macro

Static

Tunable White

User Color

Timer

000

255

–

------------ Color1 ------------

Dimmer <255>

Strobe <255>

Red <255>

Green <255>

Blue <255>

White <255>

20

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

TIMER FUNCTION (Timer)

The timer function allows the standalone modes “Colour Macro”, “Static”, “Tunable White” and

“User Colour” to be timer controlled in such a way that the fade-in time can be set from 0 to 60

minutes, the dwell time from 1 to 24 hours and the fade-out time from 0 to 60 minutes. Time

control starts immediately after activating the timer function in the previously activated stand-

alone mode and remains active even if the spotlight is switched off and restarted. Select “Timer”

by means of the procedure described above under CONFIGURE STANDALONE MODE and conﬁrm

with ENTER. Now select “Fade In”, “Dwell Time” or “Fade Out” for the individual settings (observe

arrow) and conﬁrm with ENTER. The display will show a three-digit number ﬁeld in each case. Use

UP and DOWN to set the value as required from 000 to 060 or 001 to 024. Conﬁrm by pressing

ENTER again. Once all settings have been conﬁgured as required, activate the timer function by

selecting the submenu item “Timer On/Off” using UP and DOWN, conﬁrm with ENTER, select “On”

and conﬁrm again with ENTER (to deactivate the timer function, please select “Off” and conﬁrm).

Press MODE three times to return to the main display.

------------ Timer ------------

Timer On/O

Fade In < 1min >

Dwell Time < 1h >

Fade Out < 1min >

----------- Stand Alone -----------

Auto

Color Macro

Static

Tunable White

User Color

Timer

Please note: The timer function is suitable for use in master/slave mode via cable and W-DMX™.

SLAVE MODE CONFIGURATION

Press MODE to access the selection menu. Using the UP and DOWN controls, select the menu

item “Slave” (observe arrow) and conﬁrm with ENTER. Connect the slave and the master units

(same model, same software version) with a DMX cable and enable one of the standalone modes

on the master unit (Auto, Color Macro, Static, Tunable White, User Color). Now the slave unit will

follow the master unit. If there is no control signal, the display characters will ﬂash. Flashing stops

as soon as a control signal is present.

Mode

Slave

----------------- Menu ----------------

DMX Address

DMX mode

Stand Alone

Slave

Settings

System Info

Page is loading ...

Cameo ZENIT® W300 User manual

Cameo ZENIT® W300 User manual

in other languages

Related papers

Other documents