Acrosser Technology AR-B1682 User manual

AR-B1682---SOCKET 370 PENTIUM III GRADE

CPU CARD WITH VGA/LCD/LAN/SCSI

Operation Manual

Version 1.3

~ Page ii ~

~ Page iii ~

COPYRIGHT NOTICE

This operation manual is expected to assist both Embedded Computer manufacturers and users in installing

and setting up the system. The information contained in this document is subject to change without any

notice.

Copyright Acrosser Technology Co., Ltd, 2000. All rights are reserved. No part of this publication can be

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer

language, in any form or any means, electronic, mechanical, magnetic, optical, chemical, manual or

otherwise, without the prior written consent of Acrosser Technology.

ACKNOWLEDGEMENTS

All other trademarks and registered trademarks mentioned herein are the property of their respective owners.

~ Page iv ~

~ Page v ~

~ Page vi ~

~ Page 1 ~

1. INTRODUCTION

This chapter describes:

n About This Manual

n System Specifications

n Safety precautions

n Experienced users can skip to chapter 2 on page 5 for Quick Start.

~ Page 2 ~

1-1. ABOUT THIS MANUAL

Thank you for purchasing our AR-B1682---Socket 370 Pentium III Grade CPU Card with VGA / LCD / LAN /

SCSI, fully PC / AT compatible. This manual contains five chapters. By following the instructions herein, you

can easily use AR-B1682 CPU board.

Chapter 1 Introduction

This chapter notifies you how to avoid the damages against this CPU Card as well as describes the

background of this manual and the specification of AR-B1682..

Chapter 2 Hardware Configuration

This chapter outlines the components' locations and their functions. From this part, you can find how to set

jumper and configure this card, as you need.

Chapter 3 Software Utilities

Helpful information about the proper installations of the VGA , LAN and the Watchdog-timer function are

provided in this chapter.

Chapter 4 AMI BIOS Setup

This chapter indicates you how to set up the BIOS configurations.

Appendix A Expansion Bus

This section introduces you the expansion bus for ISA BUS and PICMG .

Appendix B Technical Summary

This section gives you the information about the Technical maps.

Appendix C Trouble Shooting

This section outlines the errors might occur and some solutions are suggested.

~ Page 3 ~

1-2. SYSTEM SPECIFICATION

CPU:

Supports 333~650MHz Socket 370 Celeron / Coppermine Pentium III grade CPU

CHIPSET:

INTEL 440BX

RAM MEMORY :

Supports 3 168-pin DIMM(PC-100 SDRAM)sockets, 768Mb max.

CACHE SIZE:

Internal 128KB L2 cache inside the CPU.

ETHERNET:

Use RT8139C chipset, support 10/100M Base T with RJ-45 connector built-in LED.

SCSI:

Use SYMBIOS53C895 or equivalent, supports Ultra-Wide SCSI II with 80MB transfer rate. With one 2.54mm

68-pin SCSI connector.

SUPER I/O:

2 PCI IDE---with one 2.54 mm 40-pin connectors, and one 2.0mm 44pin connector.

1 FDC---with 2.54mm 34 -pin connector.

1 Parallel--- with 2.54 mm 26-pin connector. Supports SPP/EPP/ECP mode.

1 RS-232C-COM port 1 with DB9 connector located at bracket.

1 RS-232C/RS-485/IrDA/Touch Screen –COM port 2.

RS-232C/RS485 is selected by jumper and use the same connector.

IrDA use 2.54mm 5-pin header.

Touch Screen uses 2.0mm 3-pin JST connector.

BIOS:

AMI flash BIOS (256KB, including VGA/LCD/LAN BIOS) Supports utility program for easy to update new

version of BIOS.

KEYBOARD/MOUSE:

PS/2 compatible with 2.0mm 6-pin JST connector and 6-pin mini-DIN connector located at bracket.

BUS INTERFACE:

PICMG -ISA

VGA/LCD DISPLAY:

C&T 69000 with 2MB VRAM internally. (Dual display BIOS supported)

CRT-with HDB 15-pin connector located at bracket.

LCD-with 2.0mm 44-pin connector. (Mono/DSTN/TFT)

TV-Out-with RCA terminal.

WATCHDOG :

Built-In Supper I/O W83977 Chipset.

SYSTEM POWER REQUIREMENT:

+5V-5.0A max. & +12V-1.0A max. (Based on 500 MHz CPU).

~ Page 4 ~

USB:

Built-in 2 ports USB interface with 2.54mm 10-pin headers.

RTC:

Chipset including, Supports ACPI Function with 10 years data retention.

SPEAKER:

Supports on-board buzzer and external speaker. (with 2.5mm 4-pin header).

FLASH DISK:

Supports 1 DiskOnChip Socket 144MB.

H/W MONITORING:

Built-in (Wilnbond WB83783) hardware monitoring chipset.

HEADERS:

2-pin Reset, hard disk LED, and power/watchdog LED.

3-pin CPU cooling fan and Chassis cooling fan.

SWITCHES:

Use SMD DIP switch to select base clock and CPU clock multiplier.

BUS DRIVER CAP:

High driver for 32 TTL level loads (max.)

CPU SP:

Separated Vcore and Vio.

CE DESIGN-IN:

Add EMI components to COM ports, Parallel port, CRT, USB, Keyboard, and PS/2 mouse.

PC BOARD:

6 layers, EMI considered, especially in switching power layout.

BOARD DIMENSION:

Compact size 338.6mm x 121.9mm(13.33" x 4.80")

1-3. SAFETY PRECAUTIONS

Follow the messages hereinafter to protect your systems from damage on all occasions.

Touch a grounded metal object to discharge the static electricity in your body (or ideally, wear a grounded

wrist strap)

Stay safe from the electric shock. Don‘t touch any components of this card when the card is on. Always

switch off power when the system is not in use.

Disconnect power when changing any hardware devices. For instance, when you connect a jumper or install

any cards, a surge of power may damage the electronic components or the whole system.

~ Page 5 ~

2. HARDWARE CONFIGURATION

Four parts are included:

n Jumper & Connector Quick Reference Table

n Components’ Locations

n Configuration and Jumper settings

n Connector Pin Assignments

~ Page 6 ~

2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE

SWITCH & JUMPER:

DOC 2000 SEG ...................................................................... SW1

CPU f Ratio Selecting.............................................................. SW2

System Clock Select............................................................... SW3

RS232/485 Selection ............................................................. J1, J2, J3

DOC Memory Mapping ............................................................ JP6, JP7

Clear CMOS Function.............................................................. JP4

CONNECTOR:

COM1 Connector ................................................................... CN24

COM2 Connector ................................................................... CN12

PS/2 Connector ..................................................................... CN25

External PS/2 Connector ........................................................ CN23

Reset Switch ......................................................................... CN18

Floppy Disk Drive Connector ................................................... CN6

Hard Disk Drive Connector ...................................................... CN1, CN7

Hard Disk Drive LED Connector ............................................... CN16

Power LED & KeyLock Connector ........................................... CN13

LCD Panel Connector ............................................................. CN9, CN11

Ethernet RJ-45 Connector ....................................................... CN21

External Speaker Connector ................................................... CN20

Printer Connector ................................................................... CN2

System Fan Power Connector ................................................ CN27

SCSI Connector ..................................................................... CN3

CPU Fan Power Connector ..................................................... CN26

VGA Connector ..................................................................... CN19

IR Connector ......................................................................... CN5

Touch Screen Connector ........................................................ CN10

Power on connector for ATX Supply ......................................... CN15

Power Control Connector ........................................................ CN4

Power LED&Key Lock ............................................................ CN13

External Keyboard & Mouse Connector ................................... CN23

Watchdog LED Connector ...................................................... CN17

Universal Serial Bus Connector ............................................... CN4

Memory Installing .................................................................. DIMM1, DIMM2, DIMM3

Disk-On-Chip Socket ............................................................. U21

~ Page 7 ~

2-2. COMPONENT LOCATIONS

AR-B1682 Connector, Jumper and Component Locations

2-3. HOW TO SET JUMPERS

A jumper consists of two or three metal pins with a plastic base mounted on the card, and a small plastic cap

(with a metal contact inside) to connect the pins, so you can set up your hardware configuration by "open" or

close the pins. The jumper can be combined into sets which called jumper blocks. When the jumpers are all

in the block, you have to put them together to set up the hardware configuration. The figure below shows how

it looks.

2 PIN 3 PIN

CAP

JUMPERS AND CAP

If a jumper has three pins, for example, labelled PIN1, PIN2, and PIN3, you can either connect PIN1 & PIN2 to

create one setting and shorting or connect PIN2 & PIN3 to create another setting. The jumper setting rules are

applied throughout this manual.

CN13

CN16

~ Page 8 ~

2-4. SYSTEM CLOCK SELECT AND CPU SETTING

System clock and CPU frequency ratio are automatically detected by BIOS. Please keep sw2 ,

sw3-1 , sw3-2 ,and sw3-3 off.

2-5. RS232/485 SELECTION

The jumper settings are as follows:

(1)COM 1 & COM2 (RS232)

1

2

3

J1

Terminator

1 2 3

J2

7 8 9

1 3 5

J3

2 4 6

(2)COM 2(RS485)

1

2

3

J1

485+

485-

Terminator

1 2 3

J2

7 8 9

1 3 5

J3

2 4 6

2-6. DOC MEMORY

(1) DOC Memory Mapping Selection (JP6, JP7)

A 32-pin DOC socket supports a DOC (Disk-on-Chip) up to 72Mb. This PnP Flash ROM DOC can

be installed as one of the user’s hard disk drive. And if set as Drive C, it can be used to boot up

the computer with MS-DOS installed. It offers much faster access than a floppy or hard disk and

greatly increases reliability under harsh environment.

The DOC Memory Mapping is as follows:

DOC Memory Map

JUMPER SETTING

(pin closed)

JP6 JP7

JUMPER

ILLUSTRATION

Manufactory default --- CC000h-CDFFFh

(2) DOC 2000 SEG (SW1)

On

2 4 6 8

1 3 5 7

SEG 3-4 5-6 7-8

CC00H ON ON OFF

D000H ON OFF ON

D400H ON OFF OFF

D800H OFF ON ON

~ Page 9 ~

DC00H OFF ON OFF

E000H OFF OFF ON

DISABLE OFF OFF OFF

~ Page 10 ~

2-7. COM1 CONNECTOR(CN24)

COM1 : COM1 Connector, DB9 male connector

The COM1 Connector assignments are as follows:

PIN ASSIGNMENT

1 DCD

2 RX

3 TX

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

9 RI

2-8. COM2 CONNECTOR(CN12)

COM2 : COM2 Connector

The COM2 Connector assignments are as follows :

ASSIGNMENT

RS-232 RS-422 RS-485

1 DCD TX- DATA-

2 RX TX+ DATA+

3 TX RX+ NC

4 DTR RX- NC

5 GND GND GND

6 DSR RTS- NC

7 RTS RTS+ NC

8 CTS CTS+ NC

9 RI CTS- NC

10 NC NC NC

2-9. PS2 KB(CN25)

DIN : PS2 Connector

The PS2 connector can support Keyboard & Mouse.

The pin assignments for PS2 Connector are as follows :

PIN ASSIGNMENT

1 KBDATA

2 MSDATA

3 GND

4 Vcc

5 KBCLK

6 MSCLK

~ Page 11 ~

2-10. EXTERNAL KEYBOARD & MOUSE CONNECTOR(CN23)

EXPS2 : External PS2 Connector

The pin assignments are as follows:

PIN ASSIGNMENT

1 KBDATA

2 MSDATA

3 GND

4 Vcc

5 KBCLK

6 MSCLK

2-11. RESET SWITCH(CN18)

2 – RS

1 - GND

2-12. HDD LED Header(CN16)

1

2

Vcc

HD LED

2-13. POWER LED & KEYLOCK CONNECTOR(CN13)

1

3

2

5

4

PW LED

X

GND

K LOCK

GND

2-14. IR CONNECTOR(CN5)

1

3

2

5

4

1. +5V

2. NC

3. Rx

4. GND

5. Tx

~ Page 12 ~

2-15. FLOPPY DISK DRIVE CONNECTOR(CN6)

FDD : Floppy Disk Drive Connector

You can use a 34-pin daisy-chain cable to connect a two-FDD. One end of this cable is to attach the

FDD on the board, the other end is to attach the two-FDD.

The pin assignments are as follows:

1

2

33

34

PIN ASSIGNMENT PIN ASSIGNMENT

1 GND 2 DRVDEN0

3 GND 4 NC

5 GND 6 DRVDEN1

7 GND 8 INDEX

9 GND 10 MTR0

11 GND 12 DRV1

13 GND 14 DRV0

15 GND 16 MTR1

17 GND 18 DIR

19 GND 20 STEP

21 GND 22 WDATA

23 GND 24 WGATE

25 GND 26 TRK0

27 GND 28 WRPRT

29 GND 30 RDATA

31 GND 32 SEL

33 GND 34 DSKCHG

2-16. HARD DISK DRIVE CONNECTOR

IDE1: Hard Disk Drive Connector(CN1)

The AR-B1682 possess two HDD connectors, IDE1 and IDE2. The pin assignments are as follows:

1

2

39

40

~ Page 13 ~

PIN SIGNAL PIN SIGNAL

1 -RESET 2 GROUND

3 DATA 7 4 DATA 8

5 DATA 6 6 DATA 9

7 DATA 5 8 DATA 10

9 DATA 4 10 DATA 11

11 DATA 3 12 DATA 12

13 DATA 2 14 DATA 13

15 DATA 1 16 DATA 14

17 DATA 0 18 DATA 15

19 GROUND 20 NOT USED

21 IDEDRQA 22 GROUND

23 -LOW A 24 GROUND

25 -LOR A 26 GROUND

27 -CHRDY A 28 GROUND

29 DACKA 30 GROUND

31 -IRQ 14 32 NOT USED

33 SA 1 34 NOT USED

35 SA 0 36 SA2

37 CS 0 38 SA1

39 HD LED A 40 NOT USED

IDE2 : Hard Disk Drive Connector(CN7)

The pin assignments are as follows:

1

2

43

44

PIN SIGNAL PIN SIGNAL

1 -RESET 2 GROUND

3 DATA 7 4 DATA 8

5 DATA 6 6 DATA 9

7 DATA 5 8 DATA 10

9 DATA 4 10 DATA 11

11 DATA 3 12 DATA 12

13 DATA 2 14 DATA 13

15 DATA 1 16 DATA 14

17 DATA 0 18 DATA 15

19 GROUND 20 NOT USED

21 IDEDRQA 22 GROUND

23 -LOW A 24 GROUND

25 -LOR A 26 GROUND

27 -CHRDY A 28 GROUND

29 DACKA 30 GROUND

31 -IRQ 14 32 NOT USED

33 SA 1 34 NOT USED

35 SA 0 36 SA2

37 CS 0 38 SA1

39 HD LED A 40 NOT USED

41 VCC 42 VCC

43 GROUND 44 GROUND

~ Page 14 ~

2-17. LCD CONNECTOR 24BIT(CN9)

1

2

CN9

PIN ASSIGNMENT PIN ASSIGNMENT

1 GND 2 SHFCLK

3 GND 4 LP

5 FLM 6 GND

7 P0 8 P1

9 P2 10 P3

11 P4 12 P5

13 GND 14 P6

15 P7 16 P8

17 P9 18 P10

19 P11 20 GND

21 P12 22 P13

23 P14 24 P15

25 P16 26 P17

27 GND 28 P18

29 P19 30 P20

31 P21 32 P22

33 P23 34 GND

35 VCC 36 VCC

37 +12V 38 +12V

39 GND 40 GND

41 DE 42 ENABLK

43 GND 44 VEE

2-18. LCD CONNECTOR 36BIT(CN9+CN11)

1

2

CN9

1

2

25

26

CN11

PIN ASSIGNMENT PIN ASSIGNMENT

1 P24 2 P25

3 P26 4 P27

5 P28 6 P29

7 P30 8 P31

9 P32 10 P33

11 P34 12 P35

13 GND 14 GND

15 ENAVEE 16 ENAVEE

17 VCC3 18 VCC3

19 VLCD 20 VCLD

21 VCC 22 VCC

23 DDE 24 LP

25 DDE 26 M

Page is loading ...

Acrosser Technology AR-B1682 User manual

Acrosser Technology AR-B1682 User manual

Related papers

Other documents