American Dynamics ADQUAD87-1 Operating instructions

English

Quad Processors

Installation and Operation

ADQUAD27, ADQUAD27-1, ADQUAD47,

ADQUAD47-1, ADQUAD77, ADQUAD77-1,

ADQUAD87 and ADQUAD87-1

Part Number 8000-2133-01 REV D

Installation and Operation

ii

Notice

The information in this manual was current when published. The manufacturer reserves the right to revise

and improve its products. All specifications are therefore subject to change without notice.

Copyright

Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated

or reduced to any electronic medium or machine-readable form, in whole or in part, without prior written

American Dynamics

6795 Flanders Drive

San Diego, CA 92121-2903 U.S.A.

Customer Service

Thank you for using American Dynamics products. We support our products through an extensive

worldwide network of dealers. The dealer through whom you originally purchased this product is your point

of contact if you need service or support. Our dealers are empowered to provide the very best in customer

service and support. Dealers should contact American Dynamics at (800) 507-6268 or (561) 912-6259 or on

the Web at www.americandynamics.net.

English

Quad Processors

iii

WARNINGS

WARNING: DO NOT REMOVE COVER! NO USER SERVICABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

DO NOT INSTALL THIS PRODUCT IN HAZARDOUS AREAS WHERE HIGHLY

COMBUSTIBLE OR EXPLOSIVE PRODUTS ARE STORED OR USED.

TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

THE LIGHTNING FLASH/ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL

TRIANGLE, ALERTS THE USER TO THE PRESENCE OF A SHOCK HAZARD WITHIN

THE PRODUCT’S ENCLOSURE.

CAUTION: This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause interference

to radio communications. It has been tested and found to comply with the limits for a

Class A computing device pursuant to subpart B of part 15 of FCC rules, which are

designed to provide reasonable protection against such interference when operated in

a commercial environment. Operation of this equipment in a residential area is likely to

cause interference in which case the user at his own expense will be required to take

whatever measures may be required to correct the interference.

Changes or modifications not expressly aproved by the party responsible for

compliance could void the user's authority to operate the equipment.

This Class A digital apparatus meets all requirements of the Canadian Interference

Causing Equipment Regulations.

Cet appareil numérique de la Classe A respecte toutes lex exigencies du Réglement sur

le materiél brouilleur du Canada.

Installation and Operation

iv

Suggested Installation of Standard Quad Processor

Suggested Installation of Premium Quad Processor

Quad Processors

1

ADQUAD27 /

ADQUAD27-1

ADQUAD77 /

ADQUAD77-1

ADQUAD47 /

ADQUAD47-1

ADQUAD87 /

ADQUAD87-1

Camera Type B&W Color B&W Color

Time/Date/Title Single (monitor out only) Dual (monitor and VCR)

Remote Control N/A RS-232

Zoom on Playback N/A Yes

Video Input Channels Four

Video Loop Through Yes

On-screen Setup Yes

Alarm Sensor Type Normally Open (NO)/Normally Closed (NC); (Selectable)

Alarm Inputs Four

Alarm Call Full Screen Yes

Individual Dwell Yes

Security Lockout Yes

Rack Mount Fits standard 19” rack; single and dual kits available (optional)

Video Output Monitor: 1 V p-p; VCR: 1 p-p; Loop: 1 V p-p

Time/Date/Title Built-in clock with backup power; 8 characters for each title

Alarm Output NO and NC contacts: 1 Amp @ 24 VDC maximum

Alarm Duration Adjustable; 1 second to nonstop

Camera Dwell Adjustable; 1 second to 99 seconds

Remote Control N/A 1 to 9 units addressable

Refresh Rate 30 (NTSC/EIA); 25 (PAL/CCIR)

Resolution 512x512 (full screen) 1024x512 (full screen)

Number of Colors 256 gray scale 16.7M colors 256 gray scale 16.7M colors

Power Consumption 7.5 to 8.5 watts at 10V to 14V DC

Dimensions 215Wx309Dx44H (mm); 8.5Wx12.2Dx1.75H (in)

Operating Temperature 0° to 45°C or 32° to 113° F

Installation and Operation

2

PREMIUM QUAD PROCESSOR FRONT PANEL CONTROLS

1power — Green LED indicates the unit is on.

2 vcr/PB+ — Places unit in playback mode. Selects DIRECT for VCR setup, or FRAME or

FIELD for playback. Changes display 5–8 buttons to zoom or freeze function.

3seq — Begins or ends sequential display of full screen images at programmed dwell rate.

4set — Pressing set and display 9 button simultaneously begins or ends menu setup.

Pressing display 7 simultaneously with set restores factory default settings. Pressing set

while in playback mode returns monitor output to a live display.

5 display 5 — Displays camera 1 full screen in live mode. In playback mode, zooms or

freezes image in first quadrant. Selects alphanumeric character in menu setup.

6 display 6 — Displays camera 2 full screen in live mode. In playback mode, zooms or

freezes image in second quadrant. Selects alphanumeric character in menu setup.

7 display 7 — Displays camera 3 full screen in live mode. In playback mode, zooms or

freezes image in third quadrant. Moves cursor forward in menu setup.

8 display 8 — Displays camera 4 full screen in live mode. In playback mode, zooms or

freezes image in fourth quadrant. Moves cursor backwards in menu setup.

9 display 9 — Displays all four images in live or playback mode.

Quad Processors

3

PREMIUM QUAD PROCESSOR REAR PANEL CONNECTORS

1power — Power input connector. Only use 12 VDC center-positive power supply.

2alarm — DB9-P connector. See Alarm Connector Pin Assignments for details.

3 remote — DB9-S connector. See Remote Connector Pin Assignments for details.

4 ground — Chassis ground point with Phillips screw connector.

5 monitor — BNC connector. Delivers display output to a monitor terminated in 75 ohms.

6 vcr in — BNC connector. Accepts video signal from an attached VCR for playback.

7 vcr out — BNC connector. Delivers video signal in quad format to an attached VCR.

8 camera termination — Set camera termination ON (75Ω) or OFF (HiZ)

9 cam 1-4 in — BNC connectors. Accept video input. Auto-terminated in 75 ohms

10 cam 1-4 out — BNC connectors. Deliver video output. Auto-terminated in 75 ohms.

Installation and Operation

4

STANDARD QUAD PROCESSOR FRONT PANEL CONTROLS

1power — Green LED indicates the unit is on.

2 vcr/PB+ — Places unit in playback mode.

3 seq — Begins or ends sequential display of full screen images at programmed dwell rate.

4 set — Pressing set and display 9 button simultaneously begins or ends menu setup.

Pressing display 7 simultaneously with set restores factory default settings.

5display 5 — Displays camera 1 full screen in live mode. Selects alphanumeric character in

menu setup.

6display 6 — Displays camera 2 full screen in live mode. Selects alphanumeric character in

menu setup.

7 display 7 — Displays camera 3 full screen in live mode. Moves cursor forward in menu

setup.

8 display 8 — Displays camera 4 full screen in live mode. Moves cursor backwards in

menu setup.

9 display 9 — Displays all four images in live mode.

Quad Processors

5

STANDARD QUAD PROCESSOR REAR PANEL CONNECTORS

1power — Power input connector. Only use 12 VDC center-positive power supply.

2 alarm — DB9-P connector. See Alarm Connector Pin Assignments for details.

3 ground — Chassis ground point with Phillips screw connector.

4 monitor — BNC connector. Delivers display output to a monitor terminated in 75 ohms.

5 vcr out — BNC connector. Delivers video signal in quad format to an attached VCR.

6 vcr in — BNC connector. Accepts video signal from an attached VCR for playback.

7 camera termination — Set camera termination ON (75Ω) or OFF (HiZ)

8 cam 1-4 in — BNC connectors. Accept video input. Auto-terminated in 75 ohms

9 cam 1-4 out — BNC connectors. Deliver video output. Auto-terminated in 75 ohms.

Installation and Operation

6

MENU ONE SETTINGS: RANGE DEFAULT

SETTING

TITLE: Eight characters; A–Z, 0–9, :, /, +, -, space CAM1 thru CAM4

DWELL: 0–99 seconds 01S (One second)

TIME: HH:MM:SS; DATE: MM-DD-YY or DD-MM-YY (PAL) ON

TILE: ON or OFF ON

MENU TWO SETTINGS: RANGE DEFAULT

SETTING

SENSOR: Attached device is OPEN (NO) or CLOSED (NC) OPEN

STATUS: Unit response to attached sensor is ON or OFF ON

ALARM SENSITIVITY: Shortest pulse that triggers alarm response; 0.1

seconds to 0.8 seconds

0.3S

ALARM DURATION: Response after end of input; 0 seconds to

59 minutes

10S

AUDIBLE ALARM: Sound during alarm; ON or OFF ON

VIDEO LOSS: Video loss triggers alarm; ON or OFF ON

SECURITY LOCK: Disables front panel controls; ON or OFF OFF

UNIT ID (Premium units only): Unit number returned at TX pin of

remote connector; control up to nine units, 1–9

0 (no ID)

Quad Processors

7

CAUTION: (Premium units only) Do NOT use a cable that cannot be modified to

disable pins 6 and 7 of the remote connector, or you can cause

serious damage to the serial port of your computer or terminal.

Contact a qualified installer or technician if you cannot purchase a

connector that can be modified.

DB9-P Remote Connector

REMOTE CONNECTOR PIN ASSIGNMENTS

1Ground

2 Receive

3Transmit

4 No contact

5 No contact

6 Reserved

7 Reserved

8Ground

9Ground

DB9-S Alarm Connector

ALARM CONNECTOR PIN ASSIGNMENTS

1 Camera 1

2 Camera 2

3 Camera 3

4 Camera 4

5Alarm Reset

6Ground

7 Normally Open (NO)

8 Common

9 Normally Closed (NC)

Installation and Operation

8

REMOTE CONTROL ASCII COMMANDS

/AX Alarm Reset

/AU Factory Defaults

Either /AX or /AU Audible alarm reset

/FD VCR field mode

/FL VCR frame mode

/DR Direct mode

/22 Quad display

/01–/04 Full screen camera 1–4

/SQ Sequence

/AF Menu

/_U or /_D Text up or down

/_L or /_R Cursor left or right

/TP Toggle VCR mode

/LV End VCR mode

/ST or /SX Freeze or unfreeze playback

/TP then /01–/04 Expand playback

/LE or /LD Lock Enable/Disable

/L# Log on for unit #

/LZ Log off

Page is loading ...

Processeurs Quad

iii

WARNINGS

AVERTISSEMENT : AVERTISSEMENT : NE PAS RETIRER LE CAPOT. AUCUN ÉLÉMENT INTERNE

NE PEUT ÊTRE MANIPULÉ

PAR L’UTILISATEUR. CONTACTER UNE PERSONNE QUALIFIÉE POUR TOUTE

INTERVENTION.

N’INSTALLEZ PAS CE PRODUIT DANS DES ENDROITS PRÉSENTANT UN DANGER,

COMME PAR EXEMPLE LÀ OÙ L’ON STOCKE OU L’ON UTILISE DES PRODUITS SOIT

COMBUSTIBLES, SOIT EXPLOSIFS. POUR RÉDUIRE LES RISQUES

D’ÉLECTROCUTION, PROTÉGEZ CET APPAREIL DE LA PLUIE ET DE L’HUMIDITÉ.

L’ÉCLAIR À EXTRÉMITÉ FLÉCHÉE À L’INTÉRIEUR D’UN TRIANGLE ÉQUILATÉRAL

INDIQUE LA PRÉSENCE D’UN RISQUE D’ÉLECTROCUTION À L’INTÉRIEUR DU

PRODUIT.

AVERTISSEMENT : Cet équipement a été testé et jugé conforme aux limites de la classe A d’un

dispositif numérique, conformément à la partie 15 du Règlement de la FCC. Ces limites

sont conçues pour fournir une protection raisonnable contre les interférences

nuisibles lorsque l’équipement fonctionne dans un environnement commercial. Cet

équipement produit, utilise et peut émettre de l’énergie de radiofréquence et, s’il n’est

pas installé et utilisé conformément au manuel d’instruction, peut causer des

interférences de communication radio. L’opération de cet équipement dans les zones

habitées causera probablement des interférences nuisibles. Dans ce cas, l’utilisateur

devra corriger ces interférences à ses frais.

Les changements ou modifications qui n’ont pas été expressément approuvées par la

partie responsable de la conformité pourraient annuler l’autorité du propriétaire

d’opérer l’équipement.

Cet appareil numérique de classe A respecte toutes les exigences du Règlement sur le

matériel brouilleur du Canada.

Page is loading ...

Rack Mount Instructions - Single Unit

9

1

RM06

Single Unit Rack Mount Kit

8

Rack Mount Instructions - Dual Unit

10

2

RM07

Dual Unit Rack Mount Kit

20

American Dynamics ADQUAD87-1 Operating instructions

This manual is also suitable for

American Dynamics ADQUAD87-1 Operating instructions

in other languages

Related papers

Other documents