Whirlpool ACM 152XE0 User manual

Installation & User’s Guide

A Note To You

........................

2

Important Safety

Instructions

.............................

3

Electrical requirements

....... 4

Receptacle wiring

...............

5

Parts and Features

.................

6

Installation Instructions..

....... 7

Before you

begin..

...............

7

Tools/supplies needed

........ 8

Parts supplied for

installation

...........................

8

Installation tips

....................

9

Window installation

.............

9

Through-the-wall

installation..

.......................

13

Operating Instructions..

....... 17

Starting your air

conditioner

........................

17

Changing air direction

....... 17

Cleaning Instructions

..........

18

Cleaning the air filter..

....... 18

Cleaning the front panel..

.. 19

Maintenance Instructions..

. .20

Annual

maintenance

.........

20

Repairing paint damage..

. .22

Saving

energy

...................

22

Troubleshooting

...................

23

Requesting Assistance

or Service

..............................

24

Warranty

...............................

28

AIR CONDITIONERS

MODELS: ACM 152XE0, ACM184XE0, ACM244XEO

PART NO. 1167492 Rev. A

A Note to You

Thank you for buying a WHIRLPOOL@ appliance.

Because your life is getting busier and more complicated, WHIRLPOOL Air Conditioners are

easy to use, save time, and help you manage your home better. To ensure you enjoy years

of trouble-free operation, we developed this Use and Care Guide. It contains valuable

information about how to operate and maintain your appliance properly and safely. Please

read it carefully. Also, please complete and mail the Ownership Registration Card

provided with your appliance. This card helps us notify you about any new information

on your appliance.

Please record your model’s information.

Whenever you call to request service on

Model Number

your appliance, you need to know your

complete model number and serial number.

Serial Number

You can find this information on the model

Purchase Date

and serial number label.

Dealer Name

Please also record the purchase date of

your appliance and your dealer’s name,

Dealer Address

address, and telephone number.

Dealer Phone

Keep this book and the sales slip together in a safe place for future reference.

Our Consumer Assistance

Center number is toll-free

24-hours a day.

l-800-253-1301

2

Important Safbty Instructions

Your safety is important to us.

This guide contains safety symbols and

statements. Please pay special attention to

the symbols and follow any instructions

given. Here is a brief explanation of the use

of the symbol.

This symbol alerts you to such

dangers as fire, electrical shock,

burns, cuts, and personal injury.

To reduce the risk of fire, electrical

shock,

or

personal injury when using your air conditioner,

follow these basic

precautions:

l Read all instructions before using

. Never clean air conditioner parts with

your air conditioner.

flammable fluids. The fumes can create

*Complete the Installation Instructions

a fire hazard or explosion.

as described in this manual.

. FOR YOUR SAFETY.

l Never allow children to operate or

DO NOT STORE OR USE GASOLINE

play with the air conditioner.

OR OTHER FLAMMABLE VAPORS AND

l DO NOT operate the air conditioner

LIQUIDS IN THE VICINITY OF THIS OR

with the front panel removed.

ANY OTHER APPLIANCE. THE FUMES

l Disconnect power supply cord from

CAN CREATE A FIRE HAZARD OR

receptacle before servicing. Refer to

EXPLOSION.

model and serial number label for

BTU capacity, amperage, voltage,

and refrigerant charge specifications.

- SAVE THESE INSTRUCTIONS -

It is your responsibility to be

sure your air conditioner:

l is installed in a window or wall that will

support the weight of the unit.

l is installed and secured according to

the Installation Instructions described

in this manual.

l is connected only to the proper kind of

outlet, with the correct electrical supply

and grounding. (See “Electrical

requirements” on page 4.)

l is the proper size for the area you want

to cool.

l is used only for the job it is designed to do.

l is not used by children or anyone unable

to operate it properly.

l is properly maintained.

Also, remove the Energy Label and Buy

Guide. Use a damp cloth to take off any

glue residue. Do not use sharp instruments,

flammable fluids, or abrasive cleaner. These

can damage the material.

3

Electrical requirements

Electrical Shock Hazard

Plug air conditioner into grounded

three prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not fuse neutral or grounding

circuit.

Do not use air conditioner with

front panel removed.

Failure to follow these instructions

can result in death, electrical

shock, or serious injury.

Electrical ground is required on this

appliance.

DO NOT, UNDER ANY CIRCUMSTANCES,

REMOVE THE POWER SUPPLY CORD

GROUNDING PRONG.

OBSERVE ALL LOCAL CODES AND

ORDINANCES.

NOTE: If codes permit, and a separate

grounding wire is used, it is recommended

that a qualified electrician determine that the

grounding path is adequate. Use a time-

delay fuse or time-delay circuit breaker. It is

required that a separate circuit, serving only

this air conditioner, be provided. See the

chart on page 5 for electrical plug variations.

Choose the plug that matches your unit’s

plug. Then, use the chart to find the voltage

and ampere requirements for your air

conditioner, and the gauge of copper wire

required for the receptacle wiring.

Fire Hazard

Do not use an extension cord.

Doing so can result in death, fire, or

electrical shock.

Grounding method

For your personal safety, this appliance

must be grounded. This air conditioner

is equipped with a power supply cord

containing a 3-prong grounding plug. To

minimize possible shock hazard, the cord

must be plugged into a mating 3-prong

grounding-type wall receptacle, grounded

in accordance with all local codes and

ordinances. If a mating wall receptacle is

not available, it is the responsibility of the

consumer to have a proper wall receptacle

installed by a qualified electrician.

Receptacle wiring

See the chart below for minimum gauge for

receptacle wiring. Use copper wire only. It is

the responsibility of the consumer to provide

proper and adequate receptacle wiring,

installed by a qualified electrician. Observe

the National Electrical Code and all local

governing codes and ordinances.

REQUIREMENTS

l 115 volt (103.5 min.-

126.5 max.)

l O-l 2 amperes

l 15 amp time-delay fuse or

circuit breaker

COPPER WIRE

14 gauge

PLUG

‘.I

Bl

!’

l 230 volt (207 min.-253 max.)

or

14 gauge

l 230/208 volt (197.6 min.-

253 max.)

l O-l 2 amperes

l 15 amp time-delay fuse or

circuit breaker

l 230 volt (207 min.-253 max.)

or

12 gauge

l 230/208 volt (197.6 min.-

253 max.)

l O-l 6 amperes

l 20 amp time-delay fuse or

circuit breaker

l 230 volt (207 min.-253 max.)

or

10 gauge

l 230/208 volt (197.6 min.-

253 max.)

l O-24 amperes

l 30 amp time-delay fuse or

circuit breaker

5

Parts and Features

This section contains captioned illustrations of your appliance. Use them to become familiar

with where all parts and features are located and what they look like

TO

help you find

information on

SPeCifk

parts or features quickly, page references are included.

Airflow

direction

tab

(P. 17)\

Airflow louvers

(P. 17)

I

Control panel

/

(P. 17)

Slide-out

air filter

I

b 18)

Removable

front panel

(P. 19)

6

Installation Instructions

Proper installation of your air conditioner is important for proper operation and best cooling

results. To avoid any installation problems and to ensure trouble-free performance of your

new air conditioner, please read these Installation Instructions, as well as the operating

instructions and electrical requirements before installing your unit.

IMPORTANT: Observe all governing codes and ordinances.

Excessive Weight Hazard

Use two or more people to move and

install air conditioner.

Failure

to do so can result in back or

other injury.

Before you begin

Check the window/wall location where

the air conditioner will be installed for

the following:

l The opening/window is large enough.

Remember to add twice the thickness of

the wood to be used to build the frame.

l The wall/window is sturdy enough to

support the weight of the air conditioner -

145 to 200 pounds (65 to 90 kg).

l An electrical supply is within reach of the

power supply cord.

l Air will move freely into rooms to

be cooled.

I

Window opening measurements

Wall opening measurements

7

Tools/supplies needed

1. Flat-blade screwdriver

2. Tape measure

3. Utility knife

4. Socket wrench with

%6”

(11 mm) and %I”

(6 mm) sockets

OR

%I” (6 mm) nut driver

5. Electric drill

6. YY (2 mm) or smaller drill bit

7. Carpenter’s level

For through-the-wall installation:

8. Wood preservative

8. #l 0 x 1” (25 mm) screws [lo]

Parts supplied for installation

A. %” (10 mm) seal strips [5]

B. Side mounting brackets [2]

C. #8 x 3/B” (10 mm) hex-head sheet-metal

screws [4]

D. Filler board [l]

E. #8 x 1/2” (12.5 mm) hex-head metal

screws [4]

F. Foam seal [l]

G. Foam blocks [4]

H. #lO x %” (19 mm) round-head wood

screws [3]

I. 2%” (63.5 mm) seal strip [l]

J. Vertical supports [2]

K. Angled supports [2]

L. 3/4” (19 mm) round-head bolts [6]

M. Flat washers [6]

N. Lock washers [6]

0. Nuts [6]

P. Wall rail [l]

Q. Foam window rail seal [l]

R. Window lock bracket [l]

S. Plastic drain cup [l]

T. Gum-type sealer [l]

Installation parts are supplied for double-

hung windows up to 40” (1 ,016 mm) wide.

Installation up to 54” (1,372 mm) can be

made with a special “Wide-window kit” from

your dealer or authorized service center.

Installation tips

l Handle the air conditioner with care. Watch

l Do not install the air conditioner in an area

out for the sharp metal fins on the front

where the front panel will be exposed to

and rear coils.

heat sources that will raise the panel

l Be sure your air conditioner does not fall

surface temperature above 120°F (50°C).

out of the opening during installation.

Window installation

1. Remove the ground wire and screw from

the front of the unit base. Save grounding

screw for reattachment in Step 23.

2. Attach 3/g” (10 mm) seal strip (A) to

bottom of both side mounting brackets

(sides with screw holes). Cut strips to

length and save extra for use later.

3. Attach side mounting brackets (B) to

cabinet. Place side mounting brackets on

cabinet so bent edge is toward front of

cabinet. Attach each with 2 hex-head

metal screws (C).

4. Slide unit out of cabinet. Grasp handle

and slide unit straight out of cabinet. Place

unit on cardboard to protect your floor.

5. Place empty cabinet in window. Lower

window sash to hold cabinet in place.

Make sure the cabinet is centered in the

window opening.

6. Measure width of window channel and

subtract thickness of filler board. Cut

foam blocks 1/4” (6 mm) wider than this

measurement. The blocks will be used

later in Step 15.

7. Determine proper size for filler board

(D). Measure the distance from the right

edge of the cabinet to the inside of the

right window channel. Then add KY”

(3 mm) to that measurement. Repeat for

left side.

I

H

I

continued on next page

9

8. Cut filler board (D) to size with utility

knife. Cut in from the outside edges.

The outside edges should have screw

holes in them.

9. Apply %” (10 mm) seal strip (left over

from Step 2) to the filler boards. Apply

seal strips to the bottom front and

outside front edges of the filler boards.

10. Attach left filler board to cabinet.

Pull cabinet part way out of the window.

Then attach the left filler board to the

front of the left side mounting bracket.

Use W’ (12.5 mm) hex-head metal

screws (E).

11. Position left filler board in window

channel. Place cabinet back into

window. Make sure left filler board sits

tightly against the window channel.

12. Attach right filler board to cabinet.

Insert right filler board into right window

channel. Push filler board against right

side mounting bracket and attach it with

W’ (12.5 mm) hex-head metal screws (E).

13. Apply foam seal (F). Measure from

right inside edge of window frame to left

inside edge. Then cut the foam seal,

with square ends, to fit. Hold the cabinet

to prevent it from falling. Raise window

sash and place adhesive side of foam

seal along underside of window.

14. Make sure filler boards are as far for-

ward (toward inside room) in window

channels as possible.

15. insert foam blocks (G) into window

channels - behind filler boards about 3-

4 inches from the top and bottom edges.

The blocks keep the filler board tight to

the window channel.

10

16. Fasten cabinet to window sill. Lower

window sash firmly onto cabinet. Place a

carpenter’s level inside the cabinet and

make sure cabinet is level side-to-side.

Then drill starter holes into the cabinet

base and the window sill. Use round-

head wood screws (H) to fasten cabinet

to window sill, but do not tighten the

screws.

17. Make sure cabinet has proper out-

ward slope. Place carpenter’s level in

the right side of the cabinet. There

should be a l/2 bubble tilt (W [6 mm]per

foot [30.5 cm]) toward the outside.

Repeat for left side of cabinet. The tilt

to the outside is needed for proper

drainage.

18. Attach 2%” (63.5 mm) seal strip (I) to

inside of cabinet. Make sure the seal

strip is flush with the front edge of the

cabinet. This seal strip provides a seal

between the air conditioner base and

the cabinet.

19. Assemble the outside support. Attach

the vertical supports (J) to the angled

supports (K). Use the round-head bolts

(L), flat washers (M), lock washers (N)

and the nuts (0) for attachments. Then

attach these supports to the bottom of

the cabinet, but DO NOT tighten the

bolts at this time.

Attach the wall rail (P) to the bottom

of the supports and slide the support

assembly toward the house until the wall

rail presses firmly against the wall.

Check that you have the % bubble tilt

to the outside. This is needed for proper

drainage.

Now tighten all bolts. Tighten angled

support bolts last so wall rail fits tightly

against the house.

NOTE: If your house is constructed of

materials that could be damaged by the

wall rail, fasten a board or other protec-

tive material to the wall rail so that it is

between the wall rail and the house.

continued on next page

11

20. install foam window rail seal (Q), the

window lock bracket (R), and the

plastic drain cup (S).

l Insert foam rail seal between the top of

the lower window sash and the glass of

the upper window.

l Place window lock bracket on top of

lower window sash and against upper

window sash. Drill a starter hole

through the lock bracket into the

window sash. Attach window lock

bracket.

l Insert plastic drain cup into hole in right

side of cabinet base.

NOTE: Install window lock bracket to

prevent air conditioner from falling out of

the window.

21. Seal any small openings around

window with gum-type sealer (T).

22. insert air conditioner into cabinet.

Electrical Shock Hazard

Connect green ground wire to

cabinet.

Failure to do so can result in death

or electrical shock.

23. Reattach ground wire with grounding

screw. Put excess grounded wire

between the coils and the cabinet.

12

24. Attach the front panel. Remove the 2

front panel screws from unit base.

Replace front panel by pushing it straight

on and then lowering it slightly to lock it

in place. Attach bottom front of panel by

reinserting the 2 front panel screws.

Through-the-wall installation

It is the consumer’s responsibility and

obligation to have this product installed

by a qualified technician who is familiar

with through-the-wall room air conditioner

installations.

1. Cut an opening through the wail. Re-

move any insulation and keep for Step 8.

2. Measure depth of wail opening and

construct finish frame. Use 1” (25 mm)

or heavier lumber for wood frame con-

struction. When using a wood, metal, or

plastic molding, the finish frame should

line up with the inside wall. If a plastered

wall is to be flush with the cabinet, and no

molding is used, the finish frame must be

set %” (13 mm) back from the finished

plaster surface. See illustrations at right

for frame construction and brick veneer

construction information.

Finish frame measurements include:

A - Wall opening width

B - Wall opening height

C - Depends on wall thickness and

type of molding

NOTE: Apply wood preservative to the

surface exposed to the outside.

continued on next page

13

3. insert finish frame into wail opening.

Square and level the frame. Nail frame

securely to the wall studs.

4. Remove the ground wire and screw

from the front of the unit base. Save

grounding screw for reattachment in

Step 13.

5. Slide unit out of cabinet. Grasp handle

and slide unit straight out of cabinet.

Place unit on cardboard to protect your

floor covering.

6. insert cabinet into the wail opening.

The top of the cabinet should extend W

(13 mm) into the room. If there is trim, the

cabinet should extend W’ (13 mm) past

the trim.

7. Check the outward slope of the cabi-

net. Place a carpenter’s level inside the

cabinet on the right side. There should be

l/2 bubble (%” [6 mm] per foot [30.5 cm])

slope toward the outside. Also check the

left side.

NOTE: Make sure the air conditioner

cabinet has the proper outward slope so

condensate water runs to the outside or

damage could result to the floor or wall.

8. Seal opening between cabinet and

finish frame. Use the insulation removed

in Step 1.

9. Attach cabinet to finish frame. Use #lO

x 1” (25 mm) wood screws (not supplied)

to attach cabinet to the frame.

IMPORTANT: Do not over-tighten screws

or the cabinet will distort and provide a

poor air seal between the cabinet and the

air conditioner.

14

10. Place the 2%” (63.5 mm) seal strip (I)

inside the cabinet. Make sure the seal

is flush with the cabinet front edge.

NOTE: This seal strip fits between the

air conditioner base and the cabinet.

11. insert drain cup (S). Place drain cup

through hole in cabinet rail.

12. insert air conditioner into cabinet.

Electrical Shock Hazard

Connect green ground wire to

cabinet.

Failure to do so can result in death

or electrical shock.

lii!iJ

hII*

i

.

. . - . . * ;. . :::.. .

. . : .*-, *. . . .

:‘:,. .::*.. c .

. .

. *.>‘. -.

.,; i ::. * .

. . . . . . > . ..-.

‘.

13. Reattach ground wire with grounding

screw. Put excess grounded wire

between the coils and the cabinet.

continued on next page

15

14. Attach the front panel. Remove the

2 front panel screws from unit base.

Replace front panel by pushing it

straight on and then lowering it slightly

to lock it in place. Attach bottom front of

panel by reinserting the 2 front

panel screws.

15. Caulk ail outside wail openings

around the installation and cabinet.

16. install decorative molding. If desired,

install molding around room side of

cabinet.

16

Operating Instructions

Starting your air conditioner

1.

2.

Plug air conditioner into a grounded

3-prong outlet.

Set Fan Control to desired setting.

(All settings below not on all models.)

HIGH COOL . . . . . . . . . . . . for maximum cooling

MEDIUM COOL

. . . . . . . . . . . for normal

cooling

LOW COOL

. . . . . . . . . . . . . . for sleeping

comfort

FAN ONLY . . . . . . . . . . . . . . . . . . . .

for

circulating air

without cooling

3. Set Thermostat to a mid-setting. You can

adjust the air conditioner’s performance

by resetting the Thermostat to a higher

or lower setting. You will need to experi-

ment to find the setting(s) which work

best for you.

NOTE: If you turn your air conditioner off or

if the compressor turns off when you lower

the Thermostat, wait at least 3 minutes

before turning unit back on. Failure to do so

could blow a household fuse or trip a circuit

breaker.

Changing air direction

The louvers in the top section of the air

conditioner front panel control the direction

of the cooled air. Move the tab in the direc-

tion you want the air to go - up, down, or

straight ahead.

17

Cleaning Instructions

Proper use and care of your air conditioner will help ensure longer life of the unit and lower

operating costs. Follow these cleaning instructions.

Cleaning the air filter

The air filter is cleanable. A clean filter helps

remove dust, lint, and other particles from

the air. Check every 2 weeks to see if the

filter needs to be cleaned.

1.

2.

3.

Remove air filter from front panel.

l Grasp filter handle.

l Slide filter straight up and out of the

front panel.

Clean filter using a vacuum cleaner.

OR

If very dirty, wash filter with warm water

and a mild detergent. Air dry thoroughly

before replacing.

Replace air filter.

l Guide bottom of filter into filter slot in

front panel.

l Slide filter straight down into front panel.

NOTE: The front panel does not have to be

removed to clean the filter.

18

Cleaning the front panel

Explosion Hazard

Unplug power cord from outlet

before cleaning air conditioner.

Use only nonflammable cleaners.

Failure to follow these instructions

can result in death, explosion, fire,

or electrical shock.

1. Unplug the power cord.

2. Remove the front panel from the unit.

l Remove the 2 screws from the bottom

edge of the front panel.

l Lift front panel slightly and then pull it

toward you.

3. Remove the slide-out air filter from the

front panel. Clean it separately. See

“Cleaning the air filter.”

4. Clean front panel with warm water and a

mild soap or detergent. Use a soft cloth.

Rinse and dry.

5. Wipe the control panel clean with a soft,

dry cloth.

6. Replace the front panel.

l Push it straight onto the cabinet. Then

lower it slightly to lock it in place.

l Replace the 2 screws in the base of the

front panel.

7. Plug in the power cord.

19

Maintenance Instructions

Annual maintenance

Your air conditioner needs annual mainte-

nance to ensure steady, top performance

throughout the year.

Call the service company recommended

by your dealer to:

l Inspect and clean the coils and conden-

sate water passages.

l Check fan and fan motor.

The compressor and fan motor are sealed

and need no oiling. Expense of the annual

inspection is the consumer’s responsibility.

NOTE: If you are familiar with electrical

appliances, you can do the cleaning and

maintenance yourself. If you choose to do

so, follow these steps:

Electrical Shock Hazard

Unplug power cord from outlet

before servicing.

Be sure no liquid gets into the

motor, electrical control box, or

compressor terminals.

Failure to follow these instructions

can result in death, electrical

shock, or serious injury.

Excessive Weight Hazard

Use two or more people to move and

install air conditioner.

Failure to do so can result in back or

other injury.

20

Page is loading ...

Whirlpool ACM 152XE0 User manual

This manual is also suitable for

Whirlpool ACM 152XE0 User manual

Related papers

Other documents