The Soul Of Computer Technology
SL-56H5 / H1 USER MANUAL
USER NOTICE
This User‘s Guide & Technical Reference is for assisting system
manufacturers and end-users in setting up and installing the
mainboard.
Every effort has been made to ensure that the information in this
manual is accurate. Soltek Computer Inc. is not responsible for
printing or clerical errors. Information in this document is subject to
change without notice and does not represent a commitment on
the part of Soltek Computer Inc.
No part of this manual may be reproduced, transmitted, translated
into any language in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose
without the express written permission of Soltek Computer Inc.
Companies and products mentioned in this manual are for identifi-
cation purpose only. Product names appearing in this manual may
or may not be registered trademarks or copyrights of their respec-
tive companies.
Soltek computer inc. Provides this manual “As is “ without warranty
of any kind, either express or implied, including but not limited to
the implied warranties or conditions of merchantability or fitness
for a particular purpose. In no event shall Soltek computer inc. Be
liable for any loss or profits, loss of business, loss of use or data,
interruption of business, or for indirect, special, incidental, or con-
sequential damages of any kind, even if Soltek computer inc. Has
been advised of the possibility of such damages arising from any
defect or error in this manual or product.
Copyright © 1999, 2000 Soltek Computer Inc. All Rights Reserved.
Product Model : SL-56H5 / H1
Manual Revision : V1.0
Release Date : February 2000
• Intel Pentium, Pentium MMX are trademarks of Intel Corporation.
• VIA Apollo MVP3 is trademark of VIA Corporation.
• Cyrix MII, 6x86(L) are trademarks of Cyrix Corporation.
• AMD K6, K6-2, K6-2+, K6-III are trademarks of AMD Corporation.
• Acrobat Reader is trademark of Adobe Corporation.
• Norton AntiVirus, Norton Ghost are trademarks of Symantec Corporation.
SOLTEK AROUND THE WORLD
SOLTEK COMPUTER INC.
Address : 7F, No. 306-3, Ta-Tung Rd, Sec. 1, Hsi-Chih, Taipei-
Hsien, Taiwan, R.O.C.
Telephone : 886-2-2642-9060
Fax : 886-2-2642-9065
E-mail : [email protected]
Web site : http://www.soltek.com.tw
SOLTEK KOREA INC.
Address : 1002, Chungjin Bldg. 53-5 Wonhyo-Ro, 3-Ka,
Yongsan-Ku Seoul 140-113, Korea
Telephone : 82-2-32717400
Fax : 82-2-32717405
E-mail : [email protected]
SOUL TECHNOLOGY EUROPE B.V.
Address : Sydneystraat 52-54 3047 BP Rotterdam, the Neth-
erlands
Telephone : 31-10-2457492
Fax : 31-10-2457493
MOKA HOLDING B.V.
Address : De Run 4428 5503 LR Veldhoven, the Netherlands
Telephone : 31-402-556150
Fax : 31-402-546006
4
56H5 / 56H1
C O N T E N T
SOLTEK COMPUTER INC. ............................................. 3
SOLTEK KOREA INC. ..................................................... 3
MOKA HOLDING B.V. ..................................................... 3
SOUL TECHNOLOGY EUROPE B.V. ............................. 3
CHAPTER 1
INTRODUCTION ................................................. 6
1-1 ITEM LIST CHECKUP ..................................................... 6
1-2 CPU.................................................................................. 6
1-3 CHIPSET ......................................................................... 6
1-4 MEMORY CAPABILITY ................................................... 6
1-5 BIOS DESCRIPTION ....................................................... 7
1-6 MOTHERBOARD DESCRIPTION ................................... 7
1-7 MOTHERBOARD LAYOUT ............................................. 8
CHAPTER 2
HARDWARE SETUP.......................................... 10
2-1 VOLTAGE ADJUSTMENT ............................................. 10
• CPU Vcore Setting ........................................................... 10
• CPU Bus Clock Setting .................................................... 10
• CPU Bus Ratio Setting...................................................... 11
2-2 JUMPERS SETTING ......................................................11
• FAN#: Onboard FAN(12V) Connector ..............................11
• JP5 / JP6: CPU Single / Dual Voltage Select .................. 11
• JP10 / JP11: USB Port Select ......................................... 12
• JP12: Clear CMOS Data .................................................. 12
• JP15: Power Lost Resume .............................................. 12
• JWOL1: Wake On LAN(WOL) Connector ................... 1213
2-3 CONNECTORS ............................................................. 13
2-3.1 J2 / J3 ........................................................................ 13
5
56H5 / 56H1
2-3.2 EXTERNAL CONNECTOR ....................................... 13
2-3.3 2nd USB CONNECTOR ............................................ 14
2-3.4 ATX POWER SUPPLY CONNECTOR ...................... 15
CHAPTER 3
SOFTWARE SETUP ........................................... 16
3-1 ABOUT SOLTEK SUPPORT CD .................................. 16
3-2 HARDWARE MONITOR INSTALLATION ...................... 16
3-3 VIA CHIPSET DRIVER INSTALLATION (4-in1 Driver) 18
CHAPTER 4
BIOS SETUP ........................................................ 22
4-1 INTRODUCE THE BIOS ................................................ 22
4-2 WHAT IS BIOS SETUP ................................................. 22
4-3 HOW TO RUN BIOS SETUP......................................... 22
4-4 WHAT IS CMOS ............................................................ 23
4-5 WHAT IS POST ............................................................. 23
4-6 UPDATE THE BIOS....................................................... 23
4-6.1 BEFORE UPDATE THE BIOS ................................... 23
4-6.2 UPDATE YOUR BIOS ................................................ 23
4-6.3 COMMON ERRORS ................................................... 24
4-7 CMOS SETUP UTILITY ................................................. 26
4-7.1 STANDARD CMOS SETUP ....................................... 27
4-7.2 BIOS FEATURES SETUP .......................................... 29
4-7.3 CHIPSET FEATURES SETUP ................................... 33
4-7.4 POWER MANAGEMENT SETUP .............................. 36
4-7.5 PnP/PCI CONFIGURATION ....................................... 40
4-7.6 LOAD SETUP DEFAULTS ......................................... 43
4-7.7 INTEGRATEDPERIPHERALS ................................... 44
4-7.8 SUPERVISOR/USER PASSWORD ........................... 48
4-7.9 IDE HDD AUTO DETECTION .................................... 49
4-7.10 SAVE & EXIT SETUP............................................... 49
4-7.11 EXIT WITHOUT SAVING .......................................... 49
6
56H5 / 56H1
CHAPTER 1
INTRODUCTION
1-1 ITEM LIST CHECKUP
• Soltek Motherboard
• Soltek Support CD
• Soltek User’s Manual
• Soltek 2-in-1 Bonus Pack CD
• Soltek 2-in-1 Bonus Pack Manual
• 1.44MB floppy ribbon cable
• Ribbon cable for master and slave UltraDMA/33&UltraDMA/66 IDE
devices
1-2 CPU
• Supports Intel Pentium MMX CPUs at 166 ~ 233MHz.
• Supports Cyrix 6x86(L) CPUs at PR133+ ~ PR200+.
• Supports Cyrix 6x86(MII) CPUs at 300 ~ 466.
• Supports AMD K6-2 CPUs at 300 ~ 550MHz.
• Supports AMD K6-III CPUs at 400 ~ 550MHz.
• Supports IDT C6 CPUs at 200 ~ 300MHz.
• Supports 66/ 75/ 83/ 95/ 97/ 100/ 112/ 133 MHz CPU clock.
1-3 CHIPSET
• VIA Apollo MVP3 chipset.
• VIA 686A south bridge chip that supports UATA33/66, Hardware
Monitor function.
• PCI Rev 2.1 and APM 1.1/1.2 compliant.
• AGP v2.0(1x, 2x transfer mode) compliant.
1-4 MEMORY CAPABILITY
• Memory range from 4MB(minimum) to 768MB(maximum) with DRAM
Table Free configuration.
• Supports SDRAM with 8ns / 10ns.
7
56H5 / 56H1
• Provides 3 pcs of 168pin DIMM sockets(3.3V unbuffered 4 clock type).
1-5 BIOS DESCRIPTION
• Award BIOS.
• Supports Plug & Play (PnP).
• FLASH MEMORY for easy upgrade.
• Supports Advanced Power Management (APM) Rev 1.2 function.
• Supports Advanced Configuration Power Management Interface
(ACPI) Rev 1.0 function.
• Year 2000 compliant.
1-6 MOTHERBOARD DESCRIPTION
• Built-in onboard 512K(56H5) / 1MB(56H1) write back cache with
Piplelined Burst SRAMs.
• ATX form factor with 18.5cm x 30.5cm.
• 4 PCI Master slots, 2 ISA slots, 1 AGP slot, 1 AMR slot.
• One floppy port supports up to 2.88MB.
• 4x Built-in USB(Universal Serial Bus) controller.
• Ultra ATA33/66 bus master IDE supports up to 4 IDE devices.
(Including ZIP / LS-120 floppy devices)
• 2x 16550A Built-in fast UART compatible serial port connectors.
• Built-in SPP / EPP / ECP parallel port connectors.
• Built-in standard IrDA TX / RX header.
• Peripherals boot function with ATX power.
• Supports WOL(Wake On LAN) function. (To support WOL function,
the ATX power supply must support at least 5V standby voltage and
720mA current.)
• Supports Modem Ring Up function.
• Supports SCSI CD-ROM boot up function.
• Supports Power Lost Resume function.
• Integrated Hardware Monitor function.
8
56H5 / 56H1
1-7 MOTHERBOARD LAYOUT
• Motherboard Default Setting: AMD K6-2 350/100MHz
1 3
2 1
8 7
JP3
JP5 JP6
1 3
1 3
JP8
JP9
3 3
1 1
JP15
1 3 JP12
1 3
JP10 1 3 JP11
JFAN2
JFAN1
SPK RST PWR/LED TURBO LED
HD/LED IR PWR SUSPEND
J1
J2
15
15
JWOL1
AGP
PCI 1
PCI 2
PCI 3
PCI 4
DIMM1
DIMM2
DIMM3
FDD1
IDE2
IDE1
SOCKET 7
ATX POWER
ISA1
ISA2
FLASH BIOS
Li
Battery
Clock
Generator
LPT1
COM1 COM2 PS/2
MOUSE
PS/2
K/B
upper
lower
USB1
USB0
upper
lower
Pipelined
Burst
SRAM
Pipelined
Burst
SRAM
VIA
598
Apollo MVP3
VIA
686A
SW1
ON DIP
1 2 3 4 5 6
AMR
USB2
2 16
1 15
9
56H5 / 56H1
WATCH OUT !!!
1. Please refer to your processor installation or other
documentation attached with your CPU for detailed
installing instruction.
2. Installing a heat sink and cooling fan is necessary
for proper heat dissipation from your CPU. Uncor-
rected installation may result in overheating and
damage of your CPU.
3. Before changing the setting of CPU Vcore from
BIOS program, user SHOULD make sure of correct
specification both of CPU CLOCK and RATIO.
Uncorrected setting may cause damage to your
CPU.
10
56H5 / 56H1
1
1
1 1 1
1
1
1
1
1
1
1
1
1
1
1
2.0V 2.4V 2.8V 3.2V
3.3V
3.4V
3.5V
2.9V
3.0V
3.1V
2.5V
2.6V
2.7V
2.1V
2.2V
2.3V
JP3 JP3 JP3 JP3
Vcore
Voltage
Vcore
Voltage
Vcore
Voltage
Vcore
Voltage
K6-2 400
(or below)
K6-III MMX, 6x86L
K6 166/200
6x86MX(MII)
K6-2 233
IDT C6
Pentium
(P54C),
6x86, K5
CHAPTER 2
HARDWARE SETUP
2-1 VOLTAGE ADJUSTMENT
• CPU Vcore Setting
• CPU Bus Clock Setting
ON
OFF
ON
ON
1 2 3 4 5 6
1
3
1
3
JP8
JP9
ON
OFF
OFF
ON
1 2 3 4 5 6
1
3
1
3
JP8
JP9
ON
OFF
ON
OFF
1 2 3 4 5 6
1
3
1
3
JP8
JP9
66MHz 75MHz 83MHz
ON
ON
OFF
OFF
1 2 3 4 5 6
1
3
1
3
JP8
JP9
ON
ON
OFF
ON
1 2 3 4 5 6
1
3
1
3
JP8
JP9
ON
OFF
OFF
OFF
1 2 3 4 5 6
1
3
1
3
JP8
JP9
95MHz 97MHz 100MHz
ON
ON
ON
ON
1 2 3 4 5 6
1
3
1
3
JP8
JP9
ON
ON
ON
OFF
1 2 3 4 5 6
1
3
1
3
JP8
JP9
112MHz 133MHz
CPU CLOCK SELECT
11
56H5 / 56H1
• CPU Bus Ratio Setting
2-2 JUMPERS SETTING
• FAN#: Onboard FAN(12V) Connector
• JP5 / JP6: CPU Single / Dual Voltage Select
ON
ON
OFF
OFF
1 2 3 4 5 6
ON
ON
ON
OFF
1 2 3 4 5 6
ON
OFF
ON
OFF
1 2 3 4 5 6
ON
OFF
OFF
OFF
1 2 3 4 5 6
2.0x / 6.0x 1.5x / 3.5x2.5x 3.0x
ON
ON
OFF
ON
1 2 3 4 5 6
ON
ON
ON
ON
1 2 3 4 5 6
ON
OFF
ON
ON
1 2 3 4 5 6
ON
OFF
OFF
ON
1 2 3 4 5 6
4.0x 5.5x4.5x 5.0x
CPU BUS RATIO SELECT
JFAN# FUNCTION
JFAN1 CPU FAN
JFAN2 SYSTEM FAN
JP5 / JP6Voltage Type
1 3
1 3
JP5
JP6
1 3
1 3
JP5
JP6
Single Voltage (Intel Pentium P54C, Cyrix
6x86, AMD K5, IDT C6)
Dual Voltage (Intel Pentium-MMX, Cyrix
MII / 6x86L, AMD K6-2 / K6-2+ / K6-III)
NOTE: Only new clock generator(W83194R-58A) supports
95MHz/ 97MHz. Please check with your dealer before
using this clock.
12
56H5 / 56H1
• JP10 / JP11: USB Port Select
• JP12: Clear CMOS Data
• JP15: Power Lost Resume
This jumper allows user to use the switch of ATX power supply to control
ON/OFF switch directly instead of using the power switch on the
motherboard.
• JWOL1: Wake On LAN(WOL) Connector
This jumper is designed to use LAN to boot up the system. Connect the
wake on signal from LAN card to this connector.
NOTE: For support WOL function, the ATX power supply must support
at least 5V standby voltage / 720mA current.
JP10 / JP11USB Port
Redirect USB port2 to USB
connector (default)
1 3
1 3
JP10
JP11
Redirect USB port2 to AGP
1 3
1 3
JP10
JP11
JP12
Clear CMOS Data
Retain Data (default) 1 3
CMOS Status
1 3
NOTE: This feature must work with BIOS. Please refer to the BIOS “Power On
After PWR-Fail” sector.
Power Lost Resume JP15
Normal (default) 1 3
Enabled 1 3
13
56H5 / 56H1
2-3 CONNECTORS
• In this sector we list all external connectors that user may use.
2-3.1 J2 / J3
2-3.2 EXTERNAL CONNECTOR
A.
D. E. F. G.
B. C.
A : PS/2 MOUSE CONNECTOR
B : USB 0 CONNECTOR
C : LPT1 CONNECTOR
D : PS/2 KEYBOARD CONNECTOR
E : USB 1 CONNECTOR
F : COM2
G : COM1
1
1
15
15
A
E F G H I
C DB
A : HDD LED
B : INFRARED (IR)
C : POWER SWITCH
D : SUSPEND CONNECTOR
E : SPEAKER
F : RESET SWITCH
G : POWER LED
H : NONE
I : TURBO LED
14
56H5 / 56H1
2-3.3 2nd USB CONNECTOR
• This motherboard provides 4 sets of USB connector. Besides 2 sets of
them can be connected directly by USB device, the others are built
onboard for user to extend the use.
• When plugs the 2nd USB connector to USB2 port, user can see every
color of wires to determine which is the first pin.
PIN 1 Vcc (Red)
PIN 3 DO- (White)
PIN 5 DO+ (Green)
PIN 7 GND (Black)
PIN 9 Vcc (Red)
PIN 11 D1- (White)
PIN 13 D1+ (Green)
PIN 15 GND (Black)
PIN SIGNAL
PIN 2 GND (Black)
PIN 4 N/A
PIN 6 N/A
PIN 8 N/A
PIN 10 GND (Black)
PIN 12 N/A
PIN 14 N/A
PIN 16 N/A
PIN SIGNAL
2
1
16
15
Red Green
White Black White Black
Red
Black Black
Green
USB 2
2
116
15
USB 2
115
Soltek 2nd USB Connector (Optional)
15
56H5 / 56H1
2-3.4 ATX POWER SUPPLY CONNECTOR
• This connector connects to an ATX power supply. The plug from the
power supply only inserts in an orientation because of the different
hole sizes. Find the proper orientation and push down firmly making
sure that all pins are aligned.
• Remindering that your power supply should support at least 10mA on
the 5V standby voltage. It may cause an difficulty to power on the
system if the power supply can’t support the load.
• For Wake On LAN function, the power supply should support at least
720mA current.
+3.3 V
-12.0 V
GND
Power Supply On
GND
GND
GND
-5.0 V
+5.0 V
+5.0 V
+3.3 V
+3.3 V
GND
+5.0 V
GND
+5.0 V
GND
Power Good
+5.0 V Standby
+12.0 V
16
56H5 / 56H1
CHAPTER 3
SOFTWARE SETUP
3-1 ABOUT SOLTEK SUPPORT CD
• In Soltek support CD, it contains most informations for user’s requirement,
such as Acrobat Reader, BIOS, User’s Manual, Driver, Hardware Monitor,
Patch and Utility etc,. User can browse the CD and get further details in
regard of your motherboard. Of course, if you want to receive the newest
message about your motherboard, you can browse our web site to get it.
3-2 HARDWARE MONITOR INSTALLATION
!Please put the CD attached to
motherboard into the CD-ROM.
!There appears a welcome
window as left screen.
!Click on “ INSTALL DRIVER “
item.
!Click on the “ INSTALL VIA
CHIPSET DRIVER “.
17
56H5 / 56H1
!Click on the “ INSTALL
Hardware Monitor Utility “.
!Press Next to continue.
!The default setup destination
is C:\VIAhm, press Next to
continue.
!Press Next to finish the VIA
Hardware Monitor setup
process.
18
56H5 / 56H1
3-3 VIA CHIPSET DRIVER INSTALLATION (4-in1 Driver)
!Click on the “ INSTALL 4-in-1
Driver “.
!Click on the “ INSTALL VIA
CHIPSET DRIVER “.
!Please put the CD attached to
motherboard into the CD-ROM.
!There appears a welcome
window as left screen.
!Click on “ INSTALL DRIVER “
item.
19
56H5 / 56H1
!Press “ Next “ to continue.
!Please select the checkbox as
below.
"Bus Master PCI IDE Driver
"AGP VxD Driver
#VIA Chipset Function’s Registry
#IRQ Routing Miniport Driver
Note: In Windows 95/98 environment, user doesn’t
need to add “VIA Chipset Functions’ Registry” and
“IRQ Routing Miniport Driver” items.
!Press “ Yes “ to continue.
!Click on “ Install 4in1 Driver”
to continue.
20
56H5 / 56H1
!We do not recommend user to
select “ Enable/Disable [Ultra]
DMA ”.
Note: Whether select this item or not, user has to
enable the Hard Disk DMA function in Control
Panel manually.
(For further details, please refer to next page)
!Press Install to continue.
!The default setup destination
is C:\VIADMATOOL, press Next
to continue.
!Press Next to continue.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
