Attwood 5091-14-7 Operating instructions

Brand: Attwood

Model: 5091-14-7

Type: Operating instructions

A. Dual Locking Collar

B. Threads

C. Screw

D. Reverse Collar

LIGHT BASE_WIRING

Navigation rules require running lights (bi-color and all-round) to be operated

separately from anchor lights. Use either two separate switches or one switch

with three positions for off/anchor/running. The Bi-color navigation light requires

a 1-amp fuse. The aluminum pole is not connected to an electrical ground.

NOTICE

Navigation light poles are designed to support only the light. They

should never be used as ﬂag poles or handles.

LOCATION

Lights must be mounted to an unobstructed smooth surface on the gunwale,

deck or superstructure. Locate Bi-color Combination Light in an area as far

forward as possible (See Figure 1).

BASES THAT USE CAM-LOCK LOCKING COLLAR (FIGURE 2)

1. Remove both screws from base end of pole.

2. Slide dual locking collar (supplied) over terminal connector and past screw

holes on pole.

3. Replace only screw closest to base end of pole.

4. Align pole screw with the slot in the existing base. Insert pole into base.

5. Press down ﬁrmly to engage electrical connectors.

6. Slide locking collar down to base, rotate until you can tighten lower ring inside

top of base.

7. After installation, check lights to verify proper operation.

8. To remove, rotate locking collar in opposite direction until it loosens and pull

pole straight up

BASES THAT USE THREADED DUAL LOCKING COLLAR (FIGURE 3)

1. To reverse locking collar, remove screw at bottom of pole. Slide locking collar

off end of pole, reverse and slide on pole with non-threaded end ﬁrst.

Replace screw.

2. Align pole screw with the slot in the existing base. Insert pole into base.

3. Press down ﬁrmly to engage electrical connectors.

4. Slide locking collar down to base, align threads with base and rotate the collar

clockwise to secure ﬁt.

5. After installation, check lights to verify proper operation.

6. To remove, rotate locking collar in opposite direction (counter-clockwise)

until it loosens and pull pole straight up.

A. Dual Locking Collar

B. Lower Ring

C. Screw

Figure 2

ATTWOOD STANDARD 1-YEAR WARRANTY

See product catalog or attwoodmarine.com for details.

Figure 3

MAINTENANCE

Periodically check pole to make sure it is secure. When not in use, store in

Pole Light Storage Clips (Attwood part #7571). Choose a storage location where

light will not be damaged or be in constant contact with water. Close the base

cover when light is stowed to protect the contacts and seal the deck.

REPLACING BULB (FIGURE 5)

1. Twist lens helmet 1/4 turn counter-clockwise to remove.

2. Replace with #906 9-Watt Wedge Base Replacement Bulb (Attwood 9235-7)

available in marine, auto, and convenience stores.

3. Re-seat lens helmet and twist 1/4 turn clockwise until it clicks.

Clean the light with a mild soap and warm water solution. Never use

solvents or abrasives that may damage the lens or housing of the light.

12-Volt Bi-Color Pole Light

1 NM NAVIGATION LIGHT

5091, 5092

Installation Instructions

SAVE THESE INSTRUCTIONS

Form number 69381 Rev. C 8/2017

- For boats up to 12 meters / (39 ft) in length

- Meets USCG CFR 183.810, ABYC A-16 and all applicable standards as tested

by Imanna Laboratories 3/31/1997.

- 1 nautical mile visibility

- Use lamp 9235. #906 13v, 6 candle power.

- Impact resistant, UV stable polycarbonate housing

LIGHT POLE _ INSTALLATION

CAUTION

MAKE SURE POWER SOURCE IS 12-VOLT DC ONLY. HIGHER VOLTAGE WILL

DAMAGE LIGHT AND CIRCUITRY.

Read all instructions carefully before installing and using this product.

All positive (+12V DC) lighting wires require a 1-amp fuse to protect

circuits and vessel. The aluminum light pole is not grounded.

WARNING

To prevent personal injury, disconnect power when installing or

servicing this product. Remove boat from water before using any

120V AC power tools.

A. Red (Port)

B. Green (Starboard)

Figure 1

A B

Figure 5

Off

Lens Helmet

Bulb

Lens Bayonet

Channels

TO CONVERT POLE FOR USE WITHOUT LOCKING COLLAR (FIGURE 4)

1. For bases that do not accept locking collar, remove screw at bottom of pole.

Slide dual locking collar off end of pole.

2. Replace screw in the upper screw hole.

3. Insert pole into base, aligning screws with slot in base.

4. Press down ﬁrmly to engage electrical connectors.

5. After installation, check lights to verify proper operation.

6. To remove light, pull straight up.

Figure 4

Replacing a Light Without a Locking Collar (Figure 4)

1. Insert pole into base, aligning screws with slot in base.

2. Press down ﬁrmly to engage electrical connectors.

3. Lock pole in position with lock mechanism of base.

4. To remove light, unlock pole from base and pull straight up.

Figure 4

Attwood 5091-14-7 Operating instructions

Attwood 5091-14-7 Operating instructions

Attwood 5091-14-7 Operating instructions

Related papers

Other documents