VONN Lighting VMW11100AL Installation guide

Brand
VONN Lighting
Model
VMW11100AL
Type
Installation guide

This manual is also suitable for

©VONN Lighting,2019
Installation Guide
ON
VONN Lighting
Model:
VMW11100
Tools You May Need
GOGGLES
TAPE MEASURE
RUBBER
GLOVES
PHILLIPS
LADDER
DRILL
SCREW DRIVER
Circuit Box
Make sure that you have all necessary parts by checking the parts list. If
any part is missing or damaged, please contact VONN Lighting
Customer Service at 888-604-8666 for a replacement.
Please read and comprehend the entire manual before attempting to
assemble, operate, or install the product.
VONN highly recommends to use a qualified, licensed electrician to install
the fixture.
VONN recommends to install the fixture on its own independent circuit.
Do not install the fixture on the same circuit with other appliances, or
HVAC systems.
LED INFO & WARNINGS
•
•
All parts must be used as indicated in these instructions. Do not substitute
any parts, leave parts out, or use any parts that are worn or broken.
•
Inspect the LED fixture prior to installation to make sure that it has not
been damaged during shipping.
•
Please handle the LED light with care when unpacking. Do not apply
pressure to the LEDʼs, do not open any factory sealed compartments, and
do not touch the LEDs with your hands.
•
•
Place the wall switch in the “OFF” position of the room you are installing
the fixture.
•
Shut “OFF” the electricity at main fuse box.
•
VONN recommends ELV (Electric Low Voltage) type dimmers for this
fixture.
•
•
Do not remove or replace VONN manufactured driver that is provided
with the fixture.
Parts List
A.
B.
C.
D.
E.
F.
G.
A
F
G
B
C
D E
Mounting Bracket
Anchor Screws x 3
Outlet Screws x 3
Wire Connectors x 3
Ground Screw x 1
Canopy Screws x 2
Plastic Anchors x 3
©VONN Lighting,2019
Fixture Diagram
Canopy
Screw
Plastic
Anchor
G
B
Ground
Screw
F
Anchor
Screw
C
Wire
Connector
E
Mounting
Bracket
A
Outlet
Screw
D
Wall
Step 1. Install Mounting Bracket
©VONN Lighting,2019
Wall
Outlet Box
Wall
Outlet Box
Raise mounting bracket (A) to the wall. Mark location for
the plastic anchors (B). Drill holes for plastic anchors (B).
Insert plastic anchors (B) into hole.
Attach mounting bracket (A) to outlet box with outlet
screws (D). Screw anchor screws (C) into plastic anchors (B)
to secure mounting bracket (A).
Ground
Screw
F
Anchor
Screw
C
Mounting
Bracket
A
Outlet
Screw
D
Plastic
Anchor
B
©VONN Lighting,2019
Supply Wires:
Ground Wires:
Connect Black (Line Wire) from fixture to Black (Hot Wire)
from outlet box.
Connect White (Neutral Wire) from fixture to White (Neutral
Wire) from outlet box.
Connect Bare Copper (Ground Wire) from fixture to Green
or Bare Copper (Ground Wire) from outlet box.
Twist wires together clockwise and secure with wire
connector (E).
Installer Tip (1): If ground wire is not available in outlet box,
then secure Bare Copper (Ground Wire) from fixture to
ground screw (F) on mounting bracket (A).
Installer Tip (2): Supply wires can be either tucked into
outlet box or fixture canopy.
Wall
Step 2. Connect Wires
Wire
Connector
White
(Neutral Wire)
C
Bare Copper
(Ground Wire)
Black
(Line Wire)
Ground
Screw
F
Mounting
Bracket
A
©VONN Lighting,2019
Step 3. Mount Fixture
Wall
Attach fixture to mounting bracket (A). Secure fixture with
canopy screws (G).
Canopy
Screw
G
Mounting
Bracket
A
©VONN Lighting,2019
Step 4. Turn Power ON
Turn electricity “ON” at main fuse box.
Place the recommended ELV type dimmer switch in the “ON” position to test the fixture.
ON
ON
Circuit Box
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

VONN Lighting VMW11100AL Installation guide

Brand
VONN Lighting
Model
VMW11100AL
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents