Sunstone A-DD30 User manual

Type
User manual
When Rust-Brown marks staining occurs, it is very unlikely that the material itself is
rusting. The rust marks are the result of Three Class Types either "Pitting",
"Bleaches" & "Food Stuffs" - for which are NOT COVERED UNDER WARRANTY.
These brown marks are only superficial surface stains, which will not harm the
product; they should be removable using a damp cloth and a multi-purpose cream
cleanser. We recommend "Bar-Keepers Friend" or "Naval Jelly" for a stronger
application are bother available at your local HOME DEPOT store, also it may be
necessary to resort to a proprietary stainless steel cleanser, to return the surface of
the product to its original condition. Always first give product a full cleaning to
remove all these impurities from the steel surface. Since these particles have been
on the surface for some time, it is common for them to show signs of Rust-Brown
marks fairly quickly. Be sure to follow a regular practice of maintaining your
products material surface, to avoid this in the future. See below Examples of the
main three reasons for Rust-Brown Marks.
Pitting is the result of impurities resting on the surface of the
Stainless Steel from the Manufacturing Process. These
impurities on the steel can cause superficial rusting spots.
When this corrosive attack occurs it can often happen after
first exposure to the outside elements reveling these
impurities as dark Brown/Rust Spots. All of these can be
cleaned off, and will not return afterward.
Bleaches & Sterilizing Solutions contain Chlorine in the form of sodium
hypochlorite. Bleaches can attack the stainless steel, causing pitting of
the surface and surface staining. In most cases, this happens when the
proximity product to Pools or Spas with high chemical content that drifts
onto the surface material. All cleaning agents containing hypochlorite are
unsuitable for long term contact with stainless steel and, even when used
in the highly diluted form, they can give pitting under certain conditions.
Typically found in the groves along were two edges come together
or Drippings down vertical faces creating an area were food stuffs
collect. In general stainless steel is fully resistant to all foodstuffs in
common use. Only in isolated cases, such as when concentrated
salt and vinegar mixtures are allowed to remain in contact with the
steel for a long period can any surface marking result.
PITTING:
BLEACHES:
FOODSTUFFS:
"Superficial-Rust Staining"
SUNSTONE BBQ DOORS
CARE & MAINTENANCE GUIDE
CLEANING INSTRUCTIONS
Lay product on back so that the work area is flat, and apply generous amount of creme cleanser
like "Bar Keepers Friend" or "Naval Jelly" to the area. Be sure not to allow creme to dry on surface
or you will have to clean that off as well. Allow for several minutes for creme to rest on the surface
before going to next step.
EXAMPLE: FOOD STUFFS
EXAMPLE: BLEACHES
EXAMPLE: PITTING
Locate Dish Scrubber, like the one that has one side sponge and one side scrubber. Apply Firm
Pressure as you Scrub into Pitted/Stained materials IN THE DIRECTION OF MATERIAL GRAIN ,
still applying more crème as needed to keep area moist. Continue this process until All materials
have been removed form the surface.
If you have some materials that are more resistant to the above cleaning procedure, you can resort
to using higher Acidic Stainless Steel Cleaners. If you have any experience with using a small Blow-
Torch, you can super-heat the area were any left over pitted materials are and by applying blow-
torch to area for several seconds this will disintegrate any left over materials. Apply more cleanser
afterwards as you again scrub out any remaining materials.
We Recommend Sealing your Stainless Steel finish after each Cleaning
to prevent future staining of material.
TECHINICAL SUPPORT
888-934-9449
SERVICE@SUNSTONEMETALPRODUCTS.COM
  • Page 1 1

Sunstone A-DD30 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI