TOA RW-4800 AS User manual

Brand: TOA

Model: RW-4800 AS

Type: User manual

This manual is also suitable for

Please follow the instructions in this manual to obtain the optimum results from this unit.

We also recommend that you keep this manual handy for future reference.

RW-4800ROM WRITER

INSTRUCTION MANUAL

1. SAFETY PRECAUTIONS

• Be sure to read the instructions in this section carefully

before use.

• Make sure to observe the instructions in this manual as

the conventions of safety symbols and messages

regarded as very important precautions are included.

• We also recommend you keep this instruction manual

handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages described below are used

in this manual to prevent bodily injury and property

damage which could result from mishandling. Before

operating your product, read this manual first and

understand the safety symbols and messages so you are

thoroughly aware of the potential safety hazards.

When Installing the Unit

• Do not expose the unit to rain or an environment

where it may be splashed by water or other liquids,

as doing so may result in fire or electric shock.

• Use the unit only with the voltage specified on the

unit. Using a voltage higher than that which is

specified may result in fire or electric shock.

• Do not cut, kink, otherwise damage nor modify the

power supply cord. In addition, avoid using the

power cord in close proximity to heaters, and never

place heavy objects on the power cord, as doing so

may result in fire or electric shock.

• Avoid installing or mounting the unit in unstable

locations, such as on a rickety table or a slanted

surface. Doing so may result in the unit falling

down and causing personal injury and/or property

damage.

• To prevent lightning strikes, install the unit at least

five meters away from a lightning rod, and yet

within the protective range (angle of 45°) of the

lightning conductor. Lightning strikes may cause a

fire, electric shock or personal injury.

• Since the unit is designed for in-door use, do not

install it outdoors. If installed outdoors, the aging of

parts causes the unit to fall off, resulting in personal

injury. Also, when it gets wet with rain, there is a

danger of electric shock.

When the Unit is in Use

• Should the following irregularity be found during

use, immediately switch off the power, disconnect

the power supply plug from the AC outlet and

contact your nearest TOA dealer. Make no further

attempt to operate the unit in this condition as this

may cause fire or electric shock.

· If you detect smoke or a strange smell coming

from the unit.

· If water or any metallic object gets into the unit

· If the unit falls, or the unit case breaks

· If the power supply cord is damaged (exposure of

the core, disconnection, etc.)

· If it is malfunctioning (no tone sounds.)

• Do not place cups, bowls, or other containers of

liquid or metallic objects on top of the unit. If they

accidentally spill into the unit, this may cause a fire

or electric shock.

When Installing the Unit

• Never plug in nor remove the power supply plug

with wet hands, as doing so may cause electric

shock.

• When unplugging the power supply cord, be sure

to grasp the power supply plug; never pull on the

cord itself. Operating the unit with a damaged

power supply cord may cause a fire or electric

Indicates a potentially hazardous

situation which, if mishandled, could result in death or

serious personal injury.

Indicates a potentially hazardous

situation which, if mishandled, could result in moderate

or minor personal injury, and/or property damage.

WARNING

CAUTION

WARNING

CAUTION

2. GENERAL DESCRIPTION

The RW-4800 ROM Writer is used in conjunction with a PC to write frequency information into TOA's wireless

microphone systems, such as the WM-4200 and WM-4300 series microphones or WT-4800 series tuners.

The RW-4800 also permits the WT-4800's operating status to be monitored from the PC.

3. FEATURE

Frequency data can be written into TOA's WM-4200 and WM-4300 Series Wireless Microphones, WT-4800

Series Wireless Tuners or other TOA wireless microphone systems.

4. HANDLING PRECAUTIONS

• Use the supplied cable when connecting the RW-4800 to a PC. Switch off the PC power and remove the

AC-DC adapter from the RW-4800 when connecting or disconnecting the cable.

• Use the supplied cable for connection between the RW-4800 and equipment into which data is written.

Switch off the power of the equipment (set its power switch to OFF position or remove the AC-DC adapter)

when connecting or disconnecting the cable.

• Only the same bank wireless systems can be used in the same location. Avoid using the systems in

combination with those of different banks because interference or noise could be generated.

• Wireless tuners to be installed in the same location must differ from each other in channel number. Setting

them for the same channel number could result in noise. Wireless microphones must be identical to wireless

tuners in both bank and channel numbers.

5. NOMENCLATURE AND FUNCTIONS

[Front]

1. DC input jack

Connects to the supplied AC-DC adapter.

2. Serial port

Connect this port to the PC's serial port using the

supplied cable.

3. I/O port

Connect this port to equipment into which data is

written using the supplied cable.

2 3

shock.

• When moving the unit, be sure to remove its power

supply cord from the wall outlet. Moving the unit

with the power cord connected to the outlet may

cause damage to the power cord, resulting in fire or

electric shock. When removing the power cord, be

sure to hold its plug to pull.

• Avoid installing the unit in humid or dusty locations,

in locations exposed to the direct sunlight, near the

heaters, or in locations generating sooty smoke or

steam as doing otherwise may result in fire or

electric shock.

When the Unit is in Use

• Do not place heavy objects on the unit as this may

cause it to fall or break which may result in

personal injury and/or property damage. In

addition, the object itself may fall off and cause

injury and/or damage.

• Use the dedicated AC-DC adapter for the unit.

Note that the use of other adapter may cause a

fire.

• If dust accumulates on the power supply plug or in

the wall AC outlet, a fire may result. Clean it

periodically. In addition, insert the plug in the wall

outlet securely.

6. CD-ROM CONTENTS

(Changes or additions could be made.)

(1) TComm.dll (FILE) (2) e2_wf_a (FOLDER) (3) e2_wf_b (FOLDER)

(4) e2_wf_c (FOLDER) (5) e2_wf_d (FOLDER) (6) e2_wg_c (FOLDER)

(7) mnt_1 (FOLDER) (8) mnt_2 (FOLDER) (9) f_sample (FOLDER)

See "index.txt" for details of each program.

7. INSTALLING THE PROGRAM

(Can be installed by merely copying a file to a PC.)

Step 1. Create a folder to copy to.

Step 2. Place the disk in the CD-ROM drive and open the drive's window.

Step 3. Copy only TComm.dll to [System] Folder under [Windows] Folder.

Step 4. Copy necessary folders in the CD-ROM to the folder created in Step 1.

Step 5. The disk is no longer necessary after copying is completed.

Note

Depending upon the PC setting, all files in the CD-ROM could not be displayed. Therefore, select "Display all

files" in menu item [Setting] – [Folder option] – [Display] – [File and folder] – [Files not displayed].

8. CONNECTION

8.1. Connection of the WT-4800 to a PC

Step 1. Switch off the power of both the PC and WT-

4800, and connect the PC's serial port to the

WT-4800's remote port using the supplied cable.

Step 2. Switch on the power of the WT-4800, and then

the power of the PC.

Step 3. When writing, activate e2f_a.exe and write.

When monitoring, activate mnt_1.exe or

mnt_2.exe as required.

Step 4. After work completion, switch off the power of

both the PC and WT-4800.

Step 5. Disconnect the cable between the PC serial port

and WT-4800's remote port.

WT-4800

Serial port

REMOTE

8.2. Connection of the RW-4800 to a PC, wireless microphone and WT-4810

Step 1. After switching off the PC power and removing

the RW-4800's AC-DC adapter, connect the

PC's serial port to the RW-4800's serial port

using the supplied cable.

Step 2. Connect the AC-DC adapter to the RW-4800,

and switch on the PC power.

Step 3. Remove a rubber plug in equipment into which

data is written.

• Detach the battery case from the wireless

microphone. The plug is located near the

frequency setting switch.

• For the WT-4810, the plug is located in the

bottom panel surface.

RW-4800

WT-4810 or

wireless microphone

Serial

port

PC SERIAL PORT

I/O PORT

MICROPHONE

/TUNER

I/O Port

Plug

Wireless microphone

133-07-210-30

Power Source AC mains (Supplied AC-DC adapter must be used.)

Power Consumption 10 mA (max.)

PC system requirements Intel Pentium or faster processor

Microsoft Windows 95 or later

operating system

32 MB of RAM

10 MB of available hard-disk space (min.)

CD-ROM drive

Video card that supports 800 x 600 or greater monitor resolution

Serial port

Finish Resin, black

Operating Temperature –10 to +50°C

Dimensions 210 (w) x 44.6 (h) x 180 (d) mm

Weight 1 kg

Note: The design and specifications are subject to change without notice for improvement.

• Accessories

AC-DC adapter ........................................... 1

CD-ROM .................................................... 1

PC connection cable .................................. 1

Equipment connection cable ...................... 1

• Microsoft and Windows are trademarks of Microsoft Corporation. Intel and Pentium are trademarks of Intel Corporation.

Step 4. Connect the RW-4800's I/O port to equipment into which data is written using the supplied cable.

Step 5. Switch on the power of equipment into which data is written.

• For the wireless microphone, load a battery and set the power switch to ON position.

• For the WT-4810, connect the AC-DC adapter.

Step 6. Begin writing.

Step 7. After writing completion, switch off the power of equipment into which data is written.

• For the wireless microphone, switch off its power.

• For the WT-4810, remove the AC-DC adapter.

Step 8. Switch off the PC power.

Step 9. Remove the cable connecting the RW-4800's I/O port to equipment into which data is written.

Step 10. Put the rubber plug in equipment into which data is written.

9. SOFTWARE OPERATION

(Example: e2f_a.exe)

Activation: Open the created folder, and double-click [e2_wf_a], [Release] and

[e2f_a.exe] in this order.

Referring to the operation guide: Open the created folder, and double-click [e2_wf_a] and [Readme] in this

order.

End: Click [X] located in the upper right corner of the screen.

10. SPECIFICATIONS

TOA RW-4800 AS User manual

Brand: TOA

Model: RW-4800 AS

Type: User manual

This manual is also suitable for

Download PDF

report

TOA RW-4800 AS User manual

This manual is also suitable for

TOA RW-4800 AS User manual

Related papers

Other documents