1
z CONFIGURED USING CRIMSON SOFTWARE (VERSION 3.0 OR
LATER)
z SUPPORTS HSPA+ CELLULAR DATA CONNECTIVITY WITH FALL
BACK TO 3G AND 2G
z UP TO 21 MBPS DOWNLINK/5.76 MBPS UPLINK SPEEDS
z INSTALLS INSIDE A G3 OPERATOR INTERFACE TERMINAL
z INSTALLATION AND CONNECTION HARDWARE INCLUDED
WITH CARD
GENERAL DESCRIPTION
The G3HSPA option card allows the user to add HSPA+ cellular modem
capability to their G3 operator interface terminal. The cellular standard adopted
in this option card is HSPA+ with fallback capability to 3G and 2G. It can get
speeds up to 21 Mbps downlink and 5.76 Mbps uplink. It’s built upon the GSM
standard, offered in the US and widely available throughout the world. HSPA+
can be used for services such as Wireless Application Protocol (WAP) access,
Short Message Service (SMS), and for Internet connectivity.
The G3HSPA option card is penta-band, allowing it to work in frequencies
across the Americas, Europe and Asia. US and Canada work in the 850/1900
MHz bands, while Europe, Middle East, Africa and most of Asia work in the
900/1700/2100 MHz HSPA+ frequencies.
The G3HSPA requires the addition of a SIM (Subscriber Identity Module)
card, which is inserted into the holder prior to installation of the G3HSPA card.
The SIM card securely stores the service-subscriber key (IMSI) used to identify
a subscriber, and is used to connect to the network to obtain an IP address from
the provider.
SAFETY SUMMARY
All safety related regulations, local codes and instructions that appear in the
manual or on equipment must be observed to ensure personal safety and to
prevent damage to either the instrument or equipment connected to it. If
equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
Do not use the module to directly command motors, valves, or other actuators
not equipped with safeguards. To do so can be potentially harmful to persons or
equipment in the event of a fault to the module.
CONTENTS OF PACKAGE
- G3HSPA Option card
- Cable already attached to G3HSPA option card
- Hardware pack consisting of three screws.
- This hardware bulletin
ORDERING INFORMATION
MODEL NO. DESCRIPTION PART NUMBER
G3HSPA
GSM/HSPA+ Modem Option Card for G3
operator interface
1
G3HSPA00
ANT
2G/3G 3" hinged antenna ANT-TG090113
2G/3G/4G LTE low profile direct permanent
mount antenna, IP67 rated
ANT-G30B108111
2G/3G 4.5" whip magnetic mount antenna,
IP65 rated
ANT-GA107201111
2G/3G low profile direct permanent mount
antenna, IP65 rated
ANT-G21B301111
1
Antenna is NOT included with the card. Must be purchased separately if
needed.
SPECIFICATIONS
1. POWER REQUIREMENTS:
24VDC ± 20%; (independent from the host G3 power connection). Must use
NEC Class 2 or Limited Power Source (LPS) rated power supply.
G3HSPA Max Power:
HSPA+ Mode: During continuous active webserver traffic
Instantaneous maximum: 5.5 W
Average: 3.7 W
GPRS Mode:
Instantaneous maximum: 14.5 W (1.1 msec every 4.6 msec)
Average: 7.0 W
2. LINK STATUS LEDs:
Link Status - Link Status LED shows cellular link condition.
CAUTION: Risk of Danger.
Read complete instructions prior to
installation and operation of the unit.
MODEL G3HSPA - G3 SERIES HSPA+ CELLULAR MODEM
OPTION CARD FOR G3 OPERATOR INTERFACE TERMINALS
Bulletin No. G3HSPA-B
Drawing No. LP0965
Released 04/15
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
www.redlion.net
MOUNTING HOLES
(3 PLACES)
CONNECTOR
(SIDE 2)
POWER
ANTENNA
LED
3. COMMUNICATIONS:
Isolation from G3HSPA Antenna connector to G3 operator interface:
500 VDC for 1 minute.
4. ENVIRONMENTAL CONDITIONS:
Operating Temperature Range: 0 to 50 °C
Storage Temperature Range: -20 to 80 °C
Operating and Storage Humidity: 80% maximum relative humidity (non-
condensing) from 0 to 50 °C.
Altitude: Up to 2000 meters.
5. ANTENNA CONNECTOR:
SMA Female connector requires:
50 Ohm antenna with SMA male connector
Penta-band HSPA+ antenna (850/900/1700/1900/2100 MHz) for global
support.
Dual-band (850/1900 MHz) antenna for US and Canada only
Dual band (900/2100 MHz) for Europe only
Voltage Standing Wave Ratio (VSWR) should not exceed 2.0:1
The antenna cable should be 50Ω impedance, RG178/U or RG174/U type and
be able to connect to the RSMA (Male) jack bulkhead. The antenna could be
horizontal, vertical or right angled. Longer antenna cable would equate to
signal loss.
6. CERTIFICATIONS AND COMPLIANCES:
SAFETY:
IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment for
measurement, control and laboratory use, Part 1.
ELECTROMAGNETIC COMPATIBILITY
Emissions and Immunity to EN 61326: Electrical Equipment for Measurement,
Control and Laboratory use.
Immunity to Industrial Locations: Reference G3 unit for immunity
specifications
Emissions:
Emissions EN 55011 Class A
Note:
1. G303 unit’s emission level changes from Class B to Class A levels when
G3HSPA option card is installed.
2. The G3HSPA option card has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC rules.
7. CONSTRUCTION: Installation Category I, Pollution Degree 2.
8. INSTALLATION REQUIREMENTS: Card must be installed inside the
rear cover of a G3 operator interface with the hardware provided. See
“Installing the G3HSPA Option Card” for more details.
9. WEIGHT: 2.5 oz (70.9 g)
2
InstallIng the g3hsPa OPtIOn Card
INSTALLATION INSTRUCTIONS
Each G3HSPA option card comes with a cable for communications from the
main G3 operator interface PC board. It also comes with three screws for
attaching the option card to the inside of the G3 operator interface’s rear cover.
The first step is to buy a SIM Card from one of the GSM/HSPA+ providers
and insert into the option card SIM Card slot. The SIM Card slot is the
rectangular slot on top of the HSPA Cellular Modem in G3HSPA option card as
shown in Figure 1. See SIM Card details in the Software/Unit Operation section
for more details.
To install the option card remove all
power and communication cables from
the unit. The chassis ground
connection to the rear cover may
be left connected. The G3
operator interface literature
contains instructions for
removing the rear cover, refer
to the “Battery & Time
Keeping” section.
Using the three
screws provided,
connect the option
card to the rear cover
as shown in Figure 2.
V2 HMIs connect at
the main board.
Connect the cable from the option card to CN11 on the main board of the G3
operator interface as shown in Figure 3. Be sure both ends of the cables are
firmly seated into their appropriate connector housing.
POWER
ANTENNA
G3HSPA00
OPTION CARD
HSPA CELL MODEM
AM
SIM CARD
ORIENTATION
LED
Figure 1
Figure 2
Figure 3
Caution: The option and main circuit boards contain static
sensitive components. Before handling the cards, discharge
static charges from your body by touching a grounded bare
metal object. Ideally, handle the cards at a static controlled clean
workstation. Also, handle the cards by the edges only. Dirt, oil,
or other contaminants that may contact the card can adversely
affect circuit operation.
Warning: Depending upon the G3 operator interface, high voltage
may be present inside the operator interface. Be sure to remove
all power before removing the rear cover of the operator interface.
TOP SIDE
33
Carefully replace the rear cover by reversing the previous instructions for
removing the rear cover. An external antenna must be attached to the bracket on
the option card as shown in Figure 4. See Antenna Connector in the
Specifications section for more information.
THE OPTION CARD LABEL
Place the option card label on your rear cover in the space indicated by the
dashed lines and labeled “COMMS EXPANSION MODULE.” The label would
also display the FCC ID of the particular modem being used.
POWER SUPPLY REQUIREMENTS
NEW AND EXISTING INSTALLATIONS
The G3HSPA option card needs 24 V power independently of the G3. The
24 V power terminal connector for the G3HSPA option card is shown below.
COMMS EXPANSION MODULE
RS232
RS485
RS232
Figure 4
2 24V ± 20%
3 N/C
1 COMMON
CONNECTOR
POWER
LED
LINK STATUS – MODEM STATUS LED
The Link Status LED is a green LED that provides information regarding the
state of the modem card’s cellular connection. The status is described below.
OFF No power to the unit
ON
Powered and not registered on the cellular
network.
BLINKING Powered and registered on the cellular network.
CONFIGURING A G3HSPA OPTION CARD
The G3HSPA option card is configured using Crimson (3.0 or later) software.
After choosing the appropriate Cellular modem option card, it is set up as a PPP
Modem client (choosing HSPA+ modem in the drop down box selection), PPP
Modem Server or SMS via HSPA+ Modem. Find additional information in your
G3 device hardware literature and the Crimson 3.0 manual.
SIM CARD INSTALLATION & DETAILS
A SIM Card with data plan enabled has to be installed on the G3HSPA option
card before installing the card in the Graphite host device. Please contact your
GSM/HSPA+ cellular network provider on setting up an account and data plan.
The carrier should provide you with a SIM card to insert into the card, along
with the APN, username, and password for data connectivity.
sOftware/UnIt OPeratIOn
44
LIMITED WARRANTY
The Company warrants the products it manufactures against defects in materials and workmanship
for a period limited to two years from the date of shipment, provided the products have been stored,
handled, installed, and used under proper conditions. The Company’s liability under this limited
warranty shall extend only to the repair or replacement of a defective product, at The Company’s
option. The Company disclaims all liability for any affirmation, promise or representation with
respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against
damages, claims, and expenses arising out of subsequent sales of RLC products or products
containing components manufactured by RLC and based upon personal injuries, deaths, property
damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be
to any extent liable, including without limitation penalties imposed by the Consumer Product Safety
Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty
Act (P.L. 93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products except
those expressly contained herein. The Customer acknowledges the disclaimers and limitations
contained herein and relies on no other warranties or affirmations.
TROUBLESHOOTING YOUR G3HSPA OPTION CARD
If for any reason you have trouble operating, connecting, or simply have questions concerning your new
G3HSPA option card, contact Red Lion’s technical support. For contact information, refer to the back page
of this bulletin for phone and fax numbers.
EMAIL: [email protected]
Web Site: http://www.redlion.net
Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
Red Lion Controls
China
Unit 1102, XinMao Plaza
Building 9, No.99 Tianzhou Road
ShangHai, P.R. China 200223
Tel +86 21 6113 3688
Fax +86 21 6113 3683
Red Lion Controls
Europe
Softwareweg 9
NL - 3821 BN Amersfoort
Tel +31 (0) 334 723 225
Fax +31 (0) 334 893 793
Red Lion Controls
India
201-B, 2nd Floor, Park Centra
Opp 32 Mile Stone, Sector-30
Gurgaon-122002 Haryana, India
Tel +91 984 487 0503
/
