Ryobi RY28120 User manual

CS26

RY28120

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

26CC STRING TRIMMERS

TAILLE-BORDURES À LIGNE DE 26 CC

RECORTADORAS DE HILO 26 CC

ALL VERSIONS

TOUTES LES VERSIONS

TODAS LAS VERSIONES

Ce taille-bordures a été conçu et fabriqué conformément à

nos strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenu, cet outil vous donnera des

années de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre le

manuel d’utilisation avant d’employer ce produit.

Merci de votre achat.

Su recortadora ha sido diseñado y fabricado de conformidad con

nuestras estrictas normas para brindar fiabilidad, facilidad de uso

y seguridad para el operador. Con el debido cuidado, le brindará

muchos años de sólido funcionamiento y sin problemas.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos su compra.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your trimmer has been engineered and manufactured to our high standard for dependability, ease of operation, and opera-

tor safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

SS26

RY28140

NOTICE AVIS AVISO

Do not use E15 or E85 fuel (or fuel containing greater than 10% ethanol) in this product. It is a viola-

tion of federal law and will damage the unit and void your warranty.

Ne pas utiliser d’essence E15 ou E85 (ou un carburant contenant plus de 10 % d’éthanol) dans ce

produit. Une telle utilisation représente une violation de la loi fédérale et endommagera l’appareil et annulera la garantie.

No utilice combustibles E15 o E85 (ni combustibles que contengan más de 10 % de etanol) con este producto. Esto constituye

una violación a la ley federal, dañará la unidad y anulará la garantía.

ii

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner

toutes les figures mentionnées

dans le manuel d’utilisation.

Consulte esta sección desplegable

para ver todas las figuras a las que se

hace referencia en el manual del operador.

Page is loading ...

3 — English

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to follow all

instructions listed below may result in electric shock, fire

and/or serious personal injury.

READ ALL INSTRUCTIONS

 For safe operation, read and understand all instructions

before using this product. Follow all safety instructions.

Failure to follow all safety instructions listed below, can

result in serious personal injury.

 Do not allow children or untrained individuals to use this

unit.

 Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated

space where dangerous carbon monoxide fumes can

collect. Carbon monoxide, a colorless, odorless, and

extremely dangerous gas, can cause unconsciousness

or death.

 Clear the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or loose string

which can be thrown or become entangled in the cutting

line or blade.

 Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection

when operating this equipment.

 Wear heavy, long pants, long sleeves, boots, and gloves.

Do not wear loose fitting clothing, short pants, sandals,

or go barefoot. Do not wear jewelry of any kind.

 Heavy protective clothing may increase operator fatigue,

which could lead to heat stroke. During weather that is

hot and humid, heavy work should be scheduled for early

morning or late afternoon hours when temperatures are

cooler.

 Product users on United States Forest Service land, and in

some states, must comply with fire prevention regulations.

This product is equipped with a spark arrestor; however,

other user requirements may apply. Check with your

federal, state, or local authorities.

 Never operate this unit on the operator’s left side.

 Secure long hair above shoulder level to prevent

entanglement in moving parts.

 Keep all bystanders, children, and pets at least

50 ft. away. Bystanders should be encouraged to wear

eye protection. If you are approached, stop the engine

and cutting attachment. In the case of bladed units, there

is the added risk of injury to bystanders from being struck

with the moving blade in the event of a blade thrust or

other unexpected reaction of the saw.



Do not operate this unit when you are tired, ill, upset, or

under the influence of alcohol, drugs, or medication.

 Do not operate in poor lighting.

 Keep firm footing and balance. Do not overreach.

Overreaching can result in loss of balance or exposure

to hot surfaces.



Keep all parts of your body away from any moving part.

 To avoid hot surfaces, never operate the unit with the

bottom of the engine above waist level.



Do not touch area around the muffler or cylinder of the

unit, these parts get hot from operation. Contact with hot

surfaces could result in possible serious personal injury.



Always stop the engine and remove the spark plug wire

before making any adjustments or repairs except for

carburetor adjustments.

 Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace any damaged parts before use.

 The cutting attachment should never rotate at idle during

normal use. The cutting attachment may rotate at idle

during carburetor adjustments.

 It has been reported that vibrations from hand-held tools

may contribute to a condition called Raynaud’s Syndrome

in certain individuals. Symptoms may include tingling,

numbness, and blanching of the fingers, usually apparent

upon exposure to cold. Hereditary factors, exposure to

cold and dampness, diet, smoking, and work practices

are all thought to contribute to the development of these

symptoms. It is presently unknown what, if any, vibrations

or extent of exposure may contribute to the condition.

There are measures that can be taken by the operator to

possibly reduce the effects of vibration:

a) Keep your body warm in cold weather. When operating

the unit wear gloves to keep hands and wrists warm.

It is reported that cold weather is a major factor con-

tributing to Raynaud’s Syndrome.

b) After each period of operation, exercise to increase

blood circulation.

c) Take frequent work breaks. Limit the amount of

exposure per day.

d) Keep the tool well maintained, fasteners tightened,

and worn parts replaced.

If you experience any of the symptoms of this condition,

immediately discontinue use and see your physician about

these symptoms.

 Mix and store fuel in a container approved for gasoline.

 Mix fuel outdoors where there are no sparks or flames.

Wipe up any fuel spillage. Move 30 ft. away from refueling

site before starting engine. Slowly remove the fuel cap

after stopping engine. Do not smoke when refueling.

4 — English

SPECIFIC SAFETY RULES

 Inspect before use. Replace damaged parts. Make sure

fasteners are in place and secure. Check for fuel leaks.

 Replace string head if cracked, chipped, or damaged

in any way. Be sure the string head or blade is properly

installed and securely fastened. Failure to do so can cause

serious injury.

 Make sure all guards, straps, deflectors, and handles are

properly and securely attached.

 Never use blades, flailing devices, wire, or rope. Use only

identical replacement line in the cutting head. Do not use

any other cutting attachment. To install any other brand

of cutting head to this string trimmer can result in serious

personal injury.

 Never operate unit without the grass deflector in place

and in good condition.



Maintain a firm grip on both handles while trimming. Keep

string head below waist level. Never cut with the string

head located over 30 in. or more above the ground.

 This product is intended for infrequent use by homeown-

ers and other occasional users for such general applica-

tions as trimming light and heavy vegetation, etc. It is not

intended for prolonged use. Prolonged periods of opera-

tion can cause circulatory problems in the user’s hands

due to vibration. For such use, it may be appropriate to

use a product having an anti-vibration feature.

GENERAL SAFETY RULES

 Stop the engine and allow to cool before refueling or

storing the unit.

 Allow the engine to cool; empty the fuel tank and secure

the unit from moving before transporting in a vehicle.



Wear your protective equipment and observe all safety

instructions. For units equipped with a clutch, be sure

the cutting attachment stops turning when the engine

idles. When the unit is turned off make sure the cutting

attachment has stopped before the unit is set down.

5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe

operation of this product.

SYMBOL NAME EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and under-

stand operator’s manual before using this product.

Eye and Hearing Protection

Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection

when operating this equipment.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Ricochet

Thrown objects can ricochet and result in personal injury

or property damage.

No Blade

Do not install or use any type of blade on a product dis-

playing this symbol.

Hot Surface

To reduce the risk of injury or damage, avoid contact

with any hot surface.

Gasoline and Lubricant

Use unleaded gasoline intended for motor vehicle use

with an octane rating of 87 [(R + M) / 2] or higher. This

product is powered by a 2-cycle engine and requires

pre-mixing gasoline and 2-cycle lubricant.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

6 — English

FEATURES

PRODUCT SPECIFICATIONS

Weight - (without fuel)

CS26 ...................................................................................................................................................................10.3 lbs.

SS26 ...................................................................................................................................................................11.8 lbs.

Line cutting width

CS26 ........................................................................................................................................................................17 in.

SS26 ........................................................................................................................................................................18 in.

Engine displacement ....................................................................................................................................................26cc

Line diameter ...........................................................................................................................................................0.095 in.

KNOW YOUR PRODUCT

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

GRASS DEFLECTOR

The product includes a grass deflector that helps protect

you from flying debris.

REEL-EASY

™

TAP ADVANCE SYSTEM

The Reel-Easy

™

Tap Advance System allows easy line

advance during trimmer operation.

TOP-MOUNTED MOTOR

The top-mounted motor improves balance and is located

away from the dust and debris of the cutting area.

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the items from the box. Make sure that

all items listed in the packing list are included.

WARNING:

Do not use this product if any parts on the packing list are

already assembled to your product when you unpack it.

Parts on this list are not assembled to the product by the

manufacturer and require customer installation. Use of a

product that may have been improperly assembled could

result in serious personal injury.

 Inspect the unit carefully to make sure no damage

occurred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

CS26

Trimmer Assembly

Front Handle

Curved Shaft Grass Deflector

Bottle of 2-Cycle Lubricant

Operator’s Manual

SS26

Trimmer Assembly

Front Handle

Straight Shaft Grass Deflector

Bottle of 2-Cycle Lubricant

Operator’s Manual

7 — English

ASSEMBLY

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the engine spark plug

wire from the spark plug when assembling parts.

INSTALLING THE POWER HEAD TO THE

ATTACHMENT

See Figure 2.

WARNING:

Never install, remove, or adjust any attachment while

power head is running. Failure to stop the engine can

cause serious personal injury.

The attachment connects to the power head by means of

a coupler device.



Loosen the knob on the coupler of the power head shaft

and remove the hanger cap from the attachment.



Push in the button located on the trimmer attachment.

Align the button with the guide recess on the power

head coupler and slide the two shafts together. Rotate

the trimmer attachment until the button locks into the

positioning hole.

NOTE: If the button does not release completely in the

positioning hole, the shafts are not locked into place.

Slightly rotate from side to side until the button is locked

into place.



Tighten the knob securely.

WARNING:

Be certain the knob is fully tightened before operating

equipment; check it periodically for tightness during use

to avoid serious personal injury.

REMOVING THE ATTACHMENT FROM THE

POWER HEAD

 Loosen the knob.

 Push in the button and twist the shafts to remove and

separate ends.

ATTACHING THE STORAGE HANGER

See Figure 3.

There are two ways to hang your attachment for storage.

To use the hanger cap, push in the button and place

the hanger cap over end of trimmer attachment. Slightly

rotate the cap from side to side until the button locks into

place.

 The secondary hole in the trimmer attachment can be

used for hanging purposes as well.

ATTACHING THE FRONT HANDLE

See Figure 4.



Remove wing nut, washer, and bolt from the front handle.



Install the front handle onto the top side of the drive shaft

housing in the area indicated by the label.

NOTE: The open side of the handle should face the

operator.

 Place the bolt through the front handle.

NOTE: The hex bolt head fits inside the hex recess

molded into one side of the handle.



Reinstall the washer and wing nut.

 Tighten wing nut securely.

ATTACHING THE GRASS DEFLECTOR

WARNING:

The line cutting blade on the grass deflector is sharp.

Avoid contact with the blade. Failure to avoid contact

can result in serious personal injury.

TO ATTACH THE CURVED SHAFT GRASS

DEFLECTOR - CS26

See Figure 5.

 Remove hex screw, washer, and wing nut from grass

deflector.

 Press the grass deflector onto the bottom of the curved

shaft as shown.

 Insert the hex screw through the grass deflector and the

bracket on the curved shaft.

 Place the washer on the hex screw.

 Place the wing nut on the hex screw and tighten

securely.

8 — English

TO ATTACH THE STRAIGHT SHAFT GRASS

DEFLECTOR - SS26

See Figure 6.

 Remove the wing screw from the grass deflector.

 Insert the tab on the mounting bracket in the slot on the

grass deflector.

ASSEMBLY

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

Never use blades, flailing devices, wire, or rope on this

product. Do not use any attachments or accessories not

recommended by the manufacturer of this product. The

use of attachments or accessories not recommended

can result in serious personal injury.

WARNING:

Operation of this equipment can create sparks that can

start fires around dry vegetation. A spark arrestor may

be required. The operator should contact local fire agen-

cies for laws or regulations relating to fire prevention

requirements.

FUELING AND REFUELING THE TRIMMER

WARNING:

Gasoline and its vapors are highly flammable and ex-

plosive. To prevent serious personal injury and property

damage, handle it with care. Keep away from ignition

sources and open flames, handle outdoors only, do not

smoke and wipe up spills immediately.

FUEL MIXTURE

This product is powered by a 2-cycle engine and requires

pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded

gasoline and 2-cycle engine lubricant in a clean container

approved for gasoline. DO NOT mix quantities larger than

usable in a 30-day period.

Recommended fuel: This engine is certified to operate on

unleaded gasoline intended for automotive use.

NOTE: We recommend you use Homelite premium 2-cycle

lubricant, PowerCare 2-cycle lubricant (6.4 oz. or 16 oz.), or

an equivalent high-quality synthetic 2-cycle lubricant in this

product. Mix at 2.6 oz. per gallon (US).

Do not use automotive lubricant or 2-cycle outboard

lubricant.

HIGH QUALITY 2-CYCLE ENGINE LUBRICANT

GASOLINE LUBRICANT

1.0 gal. (US) (3.8 liter) 2.6 oz. (76 ml)

2.5 gal. (US) (9.5 liter) 6.4 oz. (189 ml)

FILLING TANK

 Clean surface around fuel cap to prevent contamination.

 Loosen fuel cap slowly. Rest the cap on a clean surface.

 Carefully pour fuel into the tank. Avoid spillage.

 Prior to replacing the fuel cap, clean and inspect the

gasket.

 Immediately replace fuel cap and hand tighten. Wipe up

any fuel spillage.

NOTE: It is normal for smoke to be emitted from a new

engine after first use.

WARNING:

Always shut off engine before fueling. Never add fuel to

a machine with a running or hot engine. Move at least

30 ft. from refueling site before starting engine. Do not

smoke! Failure to safely handle fuel could result in seri-

ous personal injury.



Align the screw hole in the mounting bracket with the

screw hole in the grass deflector.

 Insert the wing screw through the mounting bracket and

into the grass deflector.

 Tighten the screw securely.

OPERATION

9 — English

OPERATION

OXYGENATED FUELS

NOTICE:

Do not use E15 or E85 fuel (or fuel containing greater

than 10% ethanol) in this product. It is a violation of

federal law and will damage the unit and void your

warranty.

Fuel system damage or performance problems resulting

from the use of an oxygenated fuel containing more than

the percentage of oxygenates stated below are not covered

under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E15 and E85

are not.

STARTING AND STOPPING

See Figures 7 - 9.

Trimmer should be on a flat, bare surface for starting.

To start a cold engine:



Slowly press the primer bulb 10 times.

 Set the choke lever to the START (A) position.



Squeeze the throttle trigger fully and pull the starter handle

until the engine runs. Do not pull the starter grip more

than six (6) times.

NOTE: Keep throttle trigger squeezed fully through re-

maining steps. If the engine does not start, start over at

the first step with pressing the primer bulb.



Allow the engine to run for 10 seconds, then set the choke

lever to the RUN (B) position.

To restart a warm engine:



Slowly press the primer bulb 10 times.

 Set the choke lever to the RUN (B) position.



Squeeze the throttle trigger fully and pull the starter handle

until the engine runs.

To stop the engine:



To stop the engine, depress the STOP switch to the stop

position “ ”.

IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT:

Do not return this product to the retail store where it was

purchased. Please call our Customer Service Department

for any issues you may have.

For Help Call: 1-800-860-4050

OPERATING THE TRIMMER

See Figure 10.

WARNING:

Engine housing can become hot during trimmer opera-

tion. Do not rest or place your arm, hand, or any body

part against the engine housing during trimmer operation.

Only hold the trimmer as shown in Figure 10 with all body

parts clear of engine housing. Extended contact with the

engine housing can result in burns or other injuries.

WARNING:

Always position the unit on the operator’s right side. The

use of the unit on the operator’s left side will expose the

user to hot surfaces and can result in possible burn injury.

WARNING:

To avoid burns from hot surfaces, never operate unit with

the bottom of the engine above waist level.

Hold the trimmer with your right hand on the rear handle

and your left hand on the front handle. Keep a firm grip with

both hands while in operation. Trimmer should be held at a

comfortable position with the rear handle about hip height.

Always operate trimmer in RUN position. Cut tall grass

from the top down. This will prevent grass from wrapping

around the shaft housing and string head which could cause

damage from overheating. If grass becomes wrapped around

the string head, STOP THE ENGINE, disconnect the spark

plug wire, and remove the grass. Prolonged cutting at partial

throttle will result in lubricant dripping from the muffler.

WARNING:

Always hold the string trimmer away from the body keep-

ing clearance between the body and the product. Any

contact with the housing or string trimmer cutting head

can result in burns and/or other serious personal injury.

CUTTING TIPS

See Figures 10 - 12.

 Avoid hot surfaces by always keeping the tool away from

your body. (Proper operating position shown in figure 10.)

 Keep the trimmer tilted toward the area being cut; this is

the best cutting area.

 The curved shaft trimmer cuts when passing the unit from

right to left. The straight shaft trimmer cuts when passing

the unit from left to right. This will avoid throwing debris at

the operator. Avoid cutting in the dangerous area shown

in illustration.

10 — English

OPERATION

 Use the tip of line to do the cutting; do not force string

head into uncut grass.

 Wire and picket fences cause extra line wear, even

breakage. Stone and brick walls, curbs, and wood may

wear line rapidly.

 Avoid trees and shrubs. Tree bark, wood moldings, siding,

and fence posts can easily be damaged by the line.

ADVANCING STRING USING THE REEL-EASY

™

TAP ADVANCE SYSTEM

String advance is controlled by tapping the string head’s

spool retainer on grass while running engine at full throttle.

 Run engine at full throttle.

 Tap string head on ground to advance string. String

advances each time the head is tapped.

 Several taps may be required until string strikes the cut

off blade.

 Resume trimming.

NOTE: If the string is worn too short you may not be able to

advance the string by tapping it on the ground. If so, STOP

THE ENGINE, disconnect the spark plug wire, and manually

advance the string.

ADVANCING THE STRING MANUALLY

With the engine off and the spark plug wire disconnected,

push the spool retainer down while pulling on string(s) to

manually advance the string.

GRASS DEFLECTOR LINE TRIMMING CUT-OFF

BLADE

See Figure 13.

The trimmer is equipped with a line trimming cut-off blade on

the grass deflector. For best cutting, advance line until it is

trimmed to length by the cut-off blade. Advance the line when-

ever you hear the engine running faster than normal, or when

trimming efficiency diminishes. This will maintain best perfor-

mance and keep the line long enough to advance properly.

11 — English

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts could create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

Before inspecting, cleaning, or servicing the machine,

shut off engine, wait for all moving parts to stop, and

disconnect spark plug wire and move it away from spark

plug. Failure to follow these instructions can result in

serious personal injury or property damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, dust, lubricant, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating lubricants, etc., come in con-

tact with plastic parts. Chemicals can damage, weaken or

destroy plastic which could result in serious personal

injury.

You can often make adjustments and repairs described here.

For other repairs, have the trimmer serviced by an authorized

service dealer.

SPOOL REPLACEMENT

REEL-EASY

™

TAP ADVANCE SYSTEM

See Figures 14 - 16.

If replacing line only, refer to Line Replacement later in

this manual.

Use only .095 in. trimmer line.



Stop the engine and disconnect the spark plug wire. Hold

the string head and unscrew the spool retainer.

To remove the spool retainer:

Turn the spool retainer counterclockwise for CS26.

Turn the spool retainer clockwise for SS26.

MAINTENANCE

 Remove the empty spool from the string head.

NOTE: It is not necessary to remove the string head

housing from the drive shaft.



Insert the new spool into the string head.

NOTE: Make sure the arrows on the spool are aligned

with the eyelets in the string head housing. Push down

and hold the spool and housing together while complet-

ing the installation.



Reinstall the spool retainer to secure.

To install the spool retainer:

Turn the spool retainer clockwise for CS26.

Turn the spool retainer counterclockwise for SS26.

 Install line as described in Line Replacement.

LINE REPLACEMENT

See Figures 16 - 18.



Stop the engine and disconnect the spark plug wire.

 Rotate the spool clockwise as necessary to align the arrows

on the spool with the eyelets in the string head housing.

 Cut one piece of trimmer line 20 ft. long. Insert the line

into the eyelet on the string trimmer housing. Push until

the end of the line comes out the other side of the string

head. Pull the line from the other side until equal amounts

of line appear on both sides of the spool.



Rotate the spool clockwise to wind the line on the spool

until approximately 6 in. of line is showing on each side.



Push the spool retainer down while pulling on line(s) to

manually advance the line and to check for proper as-

sembly of the string head.

CLEANING THE EXHAUST PORT, MUFFLER,

AND SPARK ARRESTOR

NOTE: Depending on the type of fuel used, the type and

amount of lubricant used, and/or your operating conditions, the

exhaust port, muffler, and/or spark arrestor screen may be-

come blocked with carbon deposits. If you notice a power

loss with your gas powered tool, you may need to remove

these deposits to restore performance. We highly recom-

mend that only qualified service technicians perform this

service.

The spark arrestor must be cleaned or replaced every 50

hours or yearly to ensure proper performance of your prod-

uct. Spark arrestors may be in different locations depending

on the model purchased. Please contact your nearest service

dealer for the location of the spark arrestor for your model.

12 — English

MAINTENANCE

IDLE SPEED ADJUSTMENT

See Figure 19.

WARNING:

The cutting head will move when adjusting the idle speed.

Wear all protective clothing and keep all bystanders,

children, and pets at least 50 ft. away. Make adjustments

with the unit supported by hand so that the blade/cutting

head does not contact the ground or any object. Keep

all parts of your body away from the cutting head and

muffler. Failure to follow these instructions could result

in serious personal injury.

If the cutting attachment turns at idle, the idle speed screw

needs adjusting on the engine. Turn the idle speed screw

counterclockwise to reduce the idle RPM and stop the cut-

ting attachment movement. If the cutting attachment still

moves at idle speed, contact a service dealer for adjustment

and discontinue use until the repair is made.

WARNING:

The cutting attachment should never turn at idle. Turn

the idle speed screw counterclockwise to reduce the

idle RPM and stop the cutting attachment, or contact a

service dealer for adjustment and discontinue use until

the repair is made. Serious personal injury could result

from the cutting attachment turning at idle.

CLEANING THE AIR FILTER

See Figures 20 - 21.

For proper performance and long life, keep air filter clean.

 Remove the air filter cover by pushing down on the latches

while gently pulling off the cover.



Remove the air filter.

 Clean the foam filter element with warm soapy water.

Rinse and let dry.

NOTE: If the foam filter element is damaged, it should be

replaced.



Apply a light coat of engine oil to the foam filter element,

then squeeze it out.



Reinstall the air filter.

NOTE: Make sure the filter is seated properly inside the

cover. Installing the filter incorrectly will allow dirt to enter

the engine, causing rapid engine wear.



Replace the air filter cover by placing the slots on the air

filter cover over the latches on the housing, then push

the cover down until it snaps securely in place.

FUEL CAP, TANK, AND LINES

WARNING:

Check for fuel leaks. A leaking fuel cap, tank, or lines

are a fire hazard and must be replaced immediately. If

you find any leaks, correct the problem before using the

product. Failure to do so could result in a fire that could

cause serious personal injury.

The fuel cap contains a non-serviceable filter and a check

valve. A clogged fuel filter will cause poor engine per-

formance. If performance improves when the fuel cap is

loosened, the check valve may be faulty or filter clogged.

Replace the fuel cap if required.

SPARK PLUG REPLACEMENT

The spark plug for this engine may be replaced using a Ryobi

accessory spark plug or a Champion RCJ6Y. The spark plug

gap should be set at .025 in. Use an exact replacement and

replace annually.

NOTICE:

Be careful not to cross-thread the spark plug. Cross-

threading will seriously damage the product.

STORING THE PRODUCT

 Clean all foreign material from the product. Store idle unit

indoors in a dry, well-ventilated area that is inaccessible

to children. Keep away from corrosive agents such as

garden chemicals and de-icing salts.



Abide by all ISO and local regulations for the safe storage

and handling of gasoline.

When storing 1 month or longer:



Drain all fuel from tank into a container approved for

gasoline. Run engine until it stops.

HIGH ALTITUDE ENGINE OPERATION

Please have an authorized service center adjust this engine

if it is to be run above 2000 feet. Failure to do so may result

in poor engine performance and increased emissions. An

engine adjusted for high altitudes can not be run at 2000

feet or lower. In doing so, the engine will overheat and cause

serious engine damage. Please have an authorized service

center restore high altitude modified engines to the original

factory specification before operating below 2000 feet.

13 — English

THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER

Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s

original emission level, please refer to the maintenance section below.

CALL US FIRST

For any questions about operating or maintaining your product,

call the Ryobi

® Help Line!

Your product has been fully tested prior to shipment to ensure

your complete satisfaction.

MAINTENANCE

MAINTENANCE SCHEDULE

Inspect For Clean Replace Replace

Maintenance Damage Before Every Every 25 Hours Every

Part Each Use 5 Hours or Yearly 125 Hours

* CATALYTIC MUFFLER ASSEMBLY..................................................................................................................X

SPARK SCREEN

...............................................................................................................................................X

* AIR FILTER ASSY

includes:

Filter Screen

........................................................................ X

* CARBURETOR ASSY

includes:

Gaskets

........................................ X

* FUEL TANK ASSY

includes:

Fuel Lines

..................................... X

Fuel Cap ....................................... X

Fuel Filter................................................................................................................... X

* IGNITION ASSY

includes:

Spark Plug

................................................................................................................. X

* NOTICE:

THE USE OF EMISSION CONTROL COMPONENTS OTHER THAN THOSE DESIGNED FOR THIS UNIT

IS A VIOLATION OF FEDERAL LAW.

14 — English

PROBLEM POSSIBLE CAUSE SOLUTION

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

TROUBLESHOOTING

1. Clean or replace spark plug. Reset spark plug

gap. Refer to Spark Plug Replacement earlier

in this manual.

2. Push primer bulb until bulb is full of fuel. If bulb

does not fill, primary fuel delivery system is

blocked. Contact an authorized service dealer. If

primer bulb fills, engine may be flooded, proceed

to next item.

3. Set the CHOKE lever to the START position.

Squeeze the trigger and pull the rope repeatedly

until the engine starts and runs.

NOTE: Depending on the severity of the flooding,

this may require numerous pulls of the rope.

1. Use fresh fuel and the correct 2-cycle lubricant

mix. (50:1).

2. Clean air filter screen. Refer to Cleaning Air

Filter Screen earlier in this manual.

3. Contact an authorized servicing dealer.

4. Clean or replace spark plug. Reset spark plug

gap. Refer to Spark Plug Replacement earlier

in this manual.

1. Turn idle speed screw clockwise to increase idle

speed. See Figure 19.

1. Lubricate line with silicone spray.

2. Install more line. Refer to the applicable line

replacement section in this manual.

3. Pull lines while alternately pressing down on and

releasing spool retainer.

4. Remove line from spool and rewind. Refer to

the applicable line replacement section in this

manual.

5. Advance line at full throttle.

Engine will not start

Engine does not reach full

speed and emits excessive

smoke

Engine starts, runs, and ac-

celerates but will not idle

Line will not advance

1. No spark.

2. No fuel.

3. Engine is flooded.

1. Incorrect lubricant/fuel mixture.

2. Air filter screen is dirty.

3. Spark arrestor screen is dirty.

4. Spark plug fouled.

1. Idle speed screw on carburetor

needs adjustment.

1. Line is welded to itself.

2. Not enough line on spool.

3. Line is worn too short.

4. Line is tangled on spool.

5. Engine speed is too slow.

1. Clean threads and lubricate with grease - if no

improvement, replace the spool retainer.

1. Cut tall grass from the top down to prevent

wrapping.

2. Operate trimmer at full throttle.

Spool retainer hard to turn

Grass wraps around drive

shaft housing and string

head

1. Screw threads are dirty or

damaged.

1. Cutting tall grass at ground

level.

2. Operating trimmer at part

throttle.

15 — English

WARRANTY

LIMITED WARRANTY STATEMENT

Techtronic Industries North America, Inc., warrants to the

original retail purchaser that this RYOBI® brand outdoor

product is free from defect in material and workmanship

and agrees to repair or replace, at Techtronic Industries

North America, Inc.’s, discretion, any defective product

free of charge within these time periods from the date of

purchase.

 Three years if the product is used for personal, family

or household use;

 30 days, if used for any other purpose, such as

commercial or rental.

This warranty extends to the original retail purchaser only

and commences on the date of the original retail purchase.

Any part of this product found in the reasonable judgment

of Techtronic Industries North America, Inc. to be defective

in material or workmanship will be repaired or replaced

without charge for parts and labor by an authorized service

center for RYOBI® brand outdoor products (Authorized

Ryobi Service Center).

The product, including any defective part, must be returned

to an authorized Ryobi service center within the warranty

period. The expense of delivering the product to the service

center for warranty work and the expense of returning it

back to the owner after repair or replacement will be paid

by the owner. Techtronic Industries North America, Inc.’s,

responsibility in respect to claims is limited to making the

required repairs or replacements and no claim of breach of

warranty shall be cause for cancellation or rescission of the

contract of sale of any RYOBI® brand outdoor product. Proof

of purchase will be required by the dealer to substantiate

any warranty claim. All warranty work must be performed

by an authorized service dealer.

This warranty is limited to thirty (30) days from the date

of original retail purchase for any RYOBI® brand outdoor

product that is used for rental or commercial purposes, or

any other income-producing purpose.

This warranty does not cover any product that has been

subject to misuse, neglect, negligence, or accident, or that

has been operated in any way contrary to the operating

instructions as specified in this operator’s manual. This

warranty does not apply to any damage to the product that

is the result of improper maintenance or to any product

that has been altered or modified. The warranty does not

extend to repairs made necessary by normal wear or by the

use of parts or accessories which are either incompatible

with the RYOBI® brand outdoor product or adversely affect

its operation, performance, or durability. In addition, this

warranty does not cover:

A. Tune-ups – Spark Plugs, Carburetor, Carburetor

Adjustments, Ignition, Filters

B. Wear items – Bump Knobs, Outer Spools, Cutting

Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive

Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,

Blower Fans, Blower and Vacuum Tubes, Vacuum Bag

and Straps, Guide Bars, Saw Chains, Blades

Techtronic Industries North America, Inc., reserves the

right to change or improve the design of any RYOBI® brand

outdoor product without assuming any obligation to modify

any product previously manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE STATED WARRANTY PERIOD. ACCORDINGLY,

ANY SUCH IMPLIED WARRANTIES INCLUDING

MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE, ARE DISCLAIMED

IN THEIR ENTIRETY AFTER THE EXPIRATION OF

THE APPROPRIATE THREE-YEAR OR THIRTY-DAY

WARRANTY PERIOD. TECHTRONIC INDUSTRIES

NORTH AMERICA, INC.’S, OBLIGATION UNDER THIS

WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO

THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS

AND TECHTRONIC INDUSTRIES NORTH AMERICA,

INC., DOES NOT ASSUME OR AUTHORIZE ANYONE

TO ASSUME FOR THEM ANY OTHER OBLIGATION.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE

LIMITATION MAY NOT APPLY TO YOU. TECHTRONIC

INDUSTRIES NORTH AMERICA, INC., ASSUMES NO

RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL,

OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED

TO, EXPENSE OF RETURNING THE PRODUCT TO AN

AUTHORIZED RYOBI SERVICE CENTER AND EXPENSE

OF DELIVERING IT BACK TO THE OWNER, MECHANIC’S

TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,

RENTAL OF A LIKE PRODUCT DURING THE TIME

WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,

LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS

OF REVENUE, LOSS OF USE OF THE PRODUCT, LOSS

OF TIME, OR INCONVENIENCE. SOME STATES DO NOT

ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

This warranty applies to all RYOBI® brand outdoor products

manufactured by or for Techtronic Industries North America,

Inc., and sold in the United States and Canada.

To locate your nearest Authorized Ryobi Service Center,

dial 1-800-860-4050.

16 — English

WARRANTY

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The U.S. Environmental Protection Agency (EPA), the California Air

Resources Board (CARB), and Techtronic Industries North America,

Inc., are pleased to explain the Emissions Control System Warranty

on your new 2013/2014 small off-road engine. In California, new

equipment that uses small off-road engines must be designed, built,

and equipped to meet the state’s stringent anti-smog standards. In

other states, new small off-road engines must be designed, built, and

equipped at the time of sale to meet the U.S. EPA regulations for small

off-road engines. The small off-road engine must be free from defects

in materials and workmanship which cause it to fail to conform with

U.S. EPA standards for the first three years of engine use from the date

of sale to the ultimate purchaser. Techtronic Industries North America,

Inc., must warrant the emission control system on your small off-road

engine for the period of time listed above provided there has been no

abuse, neglect, or improper maintenance of your small off-road engine.

Your emission control system may include parts such as the carbure-

tor or fuel injection system, the ignition system, catalytic converters,

fuel tanks, valves, filters, clamps, connectors, and other associated

components. Also included may be hoses, belts and connectors, and

other emission-related assemblies.

Where a warrantable condition exists, Techtronic Industries North

America, Inc., will repair your small off-road engine at no cost to you,

including diagnosis, parts, and labor.

MANUFACTURER’S WARRANTY COVERAGE

This 1995 and later small off-road emissions control system is war-

ranted for three years. If any emission-related part on your engine is

defective, the part will be repaired or replaced by Techtronic Industries

North America, Inc.

OWNER’S WARRANTY RESPONSIBILITIES

(a) As the small off-road engine owner, you are responsible for the

performance of the required maintenance listed in your operator’s

manual. Techtronic Industries North America, Inc., recommends

that you retain all receipts covering maintenance on your small

off-road engine, but Techtronic Industries North America, Inc.,

cannot deny warranty solely for the lack of receipts or for your

failure to ensure the performance of all scheduled maintenance.

(b) As the small off-road engine owner, you should be aware, however,

that Techtronic Industries North America, Inc., may deny you warranty

coverage if your small off-road engine or a part has failed due to abuse,

neglect, improper maintenance, or unapproved modifications.

(c) You are responsible for presenting your small off-road engine to an

authorized service dealer as soon as a problem exists. The warranty

repairs should be completed in a reasonable amount of time, not to

exceed 30 days.

If you have any questions regarding your warranty rights and respon-

sibilities, you should contact a Techtronic Industries North America,

Inc., Customer Representative at 1-800-860-4050.

DEFECT WARRANTY COVERAGE REQUIREMENTS

(a) The warranty period begins on the date the engine or equipment

is delivered to an ultimate purchaser.

(b) General Emissions Warranty Coverage. Techtronic Industries North

America, Inc., warrants to the ultimate purchaser and each subsequent

purchaser that your small off-road engine is designed, built, and

equipped at the time of sale to conform with all applicable regulations

adopted by the California Air Resources Board or the United States

Environmental Protection Agency; and that it is free from defects in

materials and workmanship which cause the engine to fail to conform

with applicable regulations for a period of three years from the date

the small off-road engine is purchased by the initial purchaser. Any

replacement part or service that is equivalent in performance and

durability may be used in non-warranty maintenance or repairs, and

shall not reduce the warranty obligations of Techtronic Industries

North America, Inc.

(c) The warranty on emissions-related parts will be interpreted as

follows: Any warranted part that is not scheduled for replacement as

required in the Maintenance Schedule is warranted for three years. If

any such part (including any part that is scheduled only for regular in-

spection) fails during the period of warranty coverage, it will be repaired

or replaced at any RYOBI

® Authorized Service Center at no charge.

Any such part repaired or replaced under warranty will be warranted

for the remaining warranty period. A statement to the effect of “repair

or replace as necessary” would not reduce the period of warranty

coverage. Any warranted part that is scheduled for replacement as

required maintenance in the Maintenance Schedule is warranted for

the period of time prior to the first scheduled replacement point for that

part. Any such part repaired or replaced under warranty is warranted

for the remainder of the period prior to the first scheduled replace-

ment point, and will be repaired or replaced at any RYOBI

® Authorized

Service Center for no charge until that replacement point is reached.

Techtronic Industries North America, Inc., shall remedy warranty de-

fects at any authorized RYOBI

® Authorized Service Center, including

any distribution center that may be franchised to service the subject

engines. Any diagnostic work done at a RYOBI

® Authorized Service

Center shall be free of charge to the owner if such work determines that

a warranted part is defective. Any manufacturer-approved or equiva-

lent replacement part may be used for any warranty maintenance or

repairs on emission-related parts, and must be provided free of charge

to the owner if the part is still under warranty. Techtronic Industries

North America, Inc., is liable for damages to other engine components

caused by the failure of a warranted part still under warranty.

Add-on or modified parts that are not exempted by the California Air

Resource Board may not be used. The use of any non-exempted add-

on or modified parts will be grounds for disallowing a warranty claim.

Techtronic Industries North America, Inc., will not be liable to warrant

failures of warranted parts caused by the use of a non-exempted

add-on or modified part.

The Emission Parts List specifically defines the emission-related war-

ranted parts. Techtronic Industries North America, Inc., will provide

any documents that describe its warranty procedures or policies

within five days upon request by the California Air Resources Board.

EMISSIONS PARTS LIST

(1) Fuel Metering System

(i) Carburetor and internal parts (and/or pressure regulator or fuel

injection system).

(ii) Fuel Tank.

(iii) Fuel Hose.

(iv) Fuel Cap (EPA only)

(2) Air Induction System

(i) Intake manifold (only 4-stroke engines).

(ii) Air filter, if applicable.

(3) Ignition System

(i) Spark plugs.

(ii) Magneto or electronic ignition system.

(4) Catalyst or Thermal Reactor System

(i) Catalytic converter (only 2-stroke engines).

(5) Miscellaneous

(i) Belts (only 4-stroke engines).

Techtronic Industries North America, Inc., will furnish with each new

engine written instructions for its maintenance and use by the owner.

TECHTRONIC INDUSTRIES NORTH AMERICA, INC., CALIFORNIA AND FEDERAL EMISSION CONTROL WARRANTY

STATEMENT

17 — English

NOTES

Page is loading ...

990000227

8-22-12 (REV:02)

TECHTRONIC INDUSTRIES NORTH AMERICA, INC.

1428 Pearman Dairy Road, Anderson, SC 29625 USA

1-800-860-4050 • www.ryobitools.com

A subsidiary of Techtronic Industries Co., Ltd. • OTC: TTNDY

• PARTS AND SERVICE

Prior to requesting service or purchasing replacement parts, please obtain your model

and serial number from the product data plate.

• MODEL NO.

______________________SERIAL NO. __________________________

• HOW TO OBTAIN REPLACEMENT PARTS:

Replacement parts can be purchased online at www.ryobitools.com or by calling

1-800-860-4050. Replacement parts can also be obtained at one of our Authorized

Service Centers.

• HOW TO LOCATE AN AUTHORIZED SERVICE CENTER:

Authorized Service Centers can be located online at www.ryobitools.com or by call-

ing 1-800-860-4050.

• HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT:

To obtain Customer or Technical Support please contact us at 1-800-860-4050.

• PIÈCES ET SERVICE

Avant de faire la demande de service ou l’achat de pièces de remplacement, veuillez

obtenir le numéro de série du modèle à partir de la plaque de données du produit.

• NUMÉRO DE MODÈLE

____________NUMÉRO DE SÉRIE ___________________

• COMMENT OBTENIR LES PIÈCES DE REMPLACEMENT :

Les pièces de remplacement peuvent être achetées en ligne sur le site

www.ryobitools.com ou par téléphone au 1-800-860-4050. Les pièces de remplacement

peuvent être obtenues à un de nos centres de service autorisés.

• COMMENT TROUVER UN CENTRE DE SERVICE AUTORISÉ :

Les centres de service autorisés peuvent être localisés en ligne au www.ryobitools.

com ou en téléphonant au 1-800-860-4050.

• COMMENT OBTENIR DE L’AIDE EN CONTACTANT LE SERVICE À LA

CLIENTÈLE :

Pour contacter le service à la clientèle pour une question technique ou pour tout autre

renseignement, veuillez nous téléphoner au 1-800-860-4050.

• PIEZAS DE REPUESTO Y SERVICIO

Antes de solicitar servicio técnico o comprar piezas de repuesto, obtenga su modelo

y número de serie de la placa de datos del producto.

• NÚMERO DE MODELO

____________NÚMERO DE SERIE ___________________

• CÓMO OBTENER PIEZAS DE REPUESTO:

Las piezas de repuesto se pueden comprar en nuestro sitio en la red mundial, en la

dirección www.ryobitools.com o llamando al 1-800-860-4050. Las piezas de repuesto

también se pueden obtener en uno de nuestros Centros de Servicio Autorizados.

• CÓMO LOCALIZAR UN CENTRO DE SERVICIO AUTORIZADO:

Puede encontrar los Centros de Servicio Autorizados visitando nuestro sitio en la red

mundial, en la dirección www.ryobitools.com or by calling 1-800-860-4050.

• CÓMO OBTENER SERVICIO O ASISTENCIA TÉCNICA AL CONSUMIDOR:

Para obtener Servicio o Asistencia Técnica al Consumidor, sírvase comunicarse con

nosotros llamando al 1-800-860-4050.

OPERATOR’S MANUAL

MANUEL D’UTILISATION / MANUAL DEL OPERADOR

26CC STRING TRIMMERS

TAILLE-BORDURES À LIGNE DE 26 CC

RECORTADORAS DE HILO 26 CC

CS26 - RY28120 SS26 - RY28140

(ALL VERSIONS / TOUTES LES VERSIONS / TODAS LAS VERSIONES)

CALIFORNIA PROPOSITION 65

WARNING:

This product, its exhaust, and other sub-

stances that may become airborne from

its use may contain chemicals, including

lead, known to the State of California

to cause cancer, birth defects, or other

reproductive harm. Wash hands after

handling.

RYOBI is a registered trademark of Ryobi

Limited and is used pursuant to a license

granted by Ryobi Limited.

RYOBI est une marque déposée de RYOBI

Limited et est utilisée en vertu d’une licence

accordée par Ryobi Limited.

RYOBI es una marca registrada de Ryobi

Limited y se utiliza conforme a una licencia

otorgada por Ryobi Limited.

PROPOSITION 65 DE L’ÉTAT

DE CALIFORNIE

AVERTISSEMENT :

Ce produit, les gaz d’échappement qu’il

dégage et les autres substances rejetées

dans l’air suite à son utilisation peuvent

contenir des produits chimiques,

notamment du plomb qui, selon l’État de

la Californie, peuvent causer le cancer,

des anomalies congénitales et d’autres

dommages au système reproducteur.

Bien se laver les mains après toute

manipulation.

CALIFORNIA - PROPUESTA DE

LEY NÚM. 65

ADVERTENCIA:

Este producto, su escape y otras

sustancias que puedan llegar a ser

aerotransportadas por su uso pueden

contener sustancias químicas (incluido

el plomo) reconocidas por el estado de

California como causantes de cáncer,

defectos congénitos y otras afecciones

del aparato reproductor. Lávese las

manos después de utilizar el aparato.

Ryobi RY28120 User manual

This manual is also suitable for

Ryobi RY28120 User manual

in other languages

Related papers

Other documents