LP 1000 SERIES

Jabra LP 1000 SERIES User manual

  • Hello! I am an AI chatbot trained to assist you with the Jabra LP 1000 SERIES User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What safety precautions should be taken before starting the installation process?
    What are the additional LiteMount products that may ease the ceiling mount installation?
    What is the maximum supported load of the ceiling mount?
    How do I attach the projector to the ceiling mount?
    How do I install the projector into the ceiling mount?
    How do I adjust the angle of the projector?
    How do I invert the image on the projector?
Installation Guide
LP 1000 Series
Ceiling Mount
Installation Guide
LP 1000 Series
Installationhandbuch zur
Deckenbefestigung
English. . . . . . . . . . . . .1
Deutsch . . . . . . . . . .13
010-0154-00
Copyright © 1998 by In Focus, Inc.
Wilsonville, Oregon. All rights reserved..
Copyright © 1998 by In Focus, Inc.
Wilsonville, Oregon, USA. Alle Rechte vorbehalten.
1
CEILING MOUNT INSTALLATION GUIDE
The LP 1000 Series LiteMount
TM
makes it easy to
hang your projector from the ceiling for fixed
installation use in meeting, auditorium and
training room settings.
WARNING:
This installa-
tion must be performed in
compliance with your local
building code require-
ments. Local require-
ments take precedence
over any instructions given
in this guide.
You must determine the suitability of this prod-
uct for your intended use and assume all risk
and liability in connection therewith. In Focus
recommends that a professional contractor or
other facilities professional assist you in mount-
ing this device. Be sure to take precautions to
meet all local building codes.
Additional LiteMount Products
In Focus offers two additional LiteMount prod-
ucts that may make your ceiling mount installa-
tion easier.
The LiteMount False Ceiling Plate
(
SP-LTMT-PLT
) is designed for suspended ceil-
ings with acoustic tiles. It mounts in your ceil-
ing in place of a ceiling tile. It is pre-drilled
with holes to install the LiteMount brackets.
The LiteMount Pipe Tubing Extension (
SP-
LTMT-EXT
) allows you to install the projector
in a room with a high ceiling. With the exten-
sion, you can place the projector from 12”
(30.5) to 46” (117 cm) from the ceiling.
Contact your In Focus dealer to order these prod-
ucts.
Placing the Projector
Refer to the
LP 1000 Users Guide
for image dis-
tance, size, and angles of projection to determine
where to install the ceiling mount to meet your
projection needs.
Contents
2
Contents
The LP 1000 Series Ceiling Mount package con-
tains:
NOTE:
The maximum
load the ceiling mount can
support is 50 pounds.
1
Installation Guide
2
ceiling mount base box
dimensions: 11.6” x 10” x 1.5”
(29.5 x 25 x 3.8 cm)
weight: 3.5 lbs (1.6 kg)
3
projector mounting bracket
dimensions: 12” x 11.5” x 1.5”
(30.5 x 29.2 x 3.8 cm)
weight: 4.0 lbs (1.8 kg)
4
hardware for installing the projector mount-
ing bracket on the projector:
three (3) 4mm Phillips-head screws
three (3) 4mm quick release sleeves
one (1) 10/32 knurled knob screw
5
hardware for installing the projector (with
mounting plate) to the base box in the ceiling:
four (4) 6x12 mm knurled knob screws
two (2) 6 mm flat washers
two (2) 10 mm conical spacers
3
Install the Ceiling Mount Base Box on the Ceil-
ing
WARNING
: The ceiling
structure must be able to
support at least 5 times
the weight of the projector
and mounting hardware. If
not, it must be reinforced
according to your local
building codes.
Instructions for installing the ceiling mount on
the LiteMount False Ceiling Plate and the Lite-
Mount Pipe Tubing Extension are given in this
installation guide. If you have not purchased
either of these products, consult a professional
contractor or other facilities professional to
ensure a safe installation.
Please refer to the LiteMount False Ceiling Plate
and LiteMount Pipe Tubing Extension installa-
tion instructions for lists of included hardware.
1
Center the ceiling mount base box on the ceil-
ing plate as shown in Figure 1. Make sure the
front of the base box faces forward toward
your projection screen. The front side of the
base box is the only surface without drilled
holes.
2a
LiteMount False Ceiling Plate - Align the
holes in the base box with the threaded studs
on the plate. Install the 4 washers and nuts as
shown in Figure 1.
NOTE
: Refer to the
Installation Instructions
that came with the Lite-
Mount False Ceiling Plate
and the LiteMount Pipe
Tubing Extension for
important additional infor-
mation.
2b
LiteMount Pipe Tubing Extension - Line up
the holes in the base box with the holes in the
plate at the end of the pipe extension. Install
the hardware as shown in Figure 2.
Install the Ceiling Mount Base Box on the Ceiling
4
3
Place the ceiling plate or pipe extension in the
ceiling so that the base box hangs down into
the room.
WARNING
: If the
dropped ceiling is an air-
handling plenum, be sure
the cables are plenum-
rated, or install the cables
within conduit.
4
Route the projectors cables through your
ceiling and out the hole in the ceiling
(Figure 7).
F
IGURE
1
Install the base box to the LiteMount False Ceiling Plate
make sure this
surface faces front
5
F
IGURE
2
Install the base box to the LiteMount Pipe Tubing Extension
surface faces front
make sure this
Attach the Mounting Plate to the Projector
6
Attach the Mounting Plate to the Projector
1
Set the projector on a table with the bottom
side up.
CAUTION
: Use only the
hardware that is provided
with the LP 1000 Series
Ceiling Mount. Using
different hardware may
damage your projector.
2
Insert the 3 screws into the 3 quick release
sleeves (Figure 3).
3
Attach the screws and sleeves to the holes in
the projector as shown in Figure 3. Be careful
not to over-tighten the bolts.
4
Align the keyholes in the mounting bracket
with the screws in the projector. Slide the
mounting bracket until the quick release
sleeves are at the top of the keyhole slot.
5
Attach the 10/32 knurled knob to the projec-
tor in the location shown in Figure 3.
F
IGURE
3
Attach the mounting plate to the projector
quick release screws
knurled knob
goes here
quick release screw
7
Hang the Projector on the Ceiling
1
Loosely install the 12 mm knurled knobs, flat
washers, and conical spacers to the 2 hinge
pins on the base box (Figure 4).
F
IGURE
4
Attach knurled knobs to the side of the base box
2
Make sure your cables are pulled through the
center hole of the base box, then carefully lift
the projector and turn it upside down so the
mounting plate faces the ceiling.
3
Insert the projector and mounting bracket
into the base box through the space between
the knurled knobs and base box (Figure 4).
Slide the projector bracket forward until the
knurled knobs rest fully in the vertical slots
and support the projector. Tighten the
knurled knobs completely.
slide projector
bracket here between
the base box and the knurled knob
knurled knob
knurled knob
spacer
washer
Hang the Projector on the Ceiling
8
F
IGURE
5
Install the projector in the ceiling base box
4
Insert the remaining two 6 mm knurled
knobs through the rear slots in the mounting
bracket and into the holes on the sides of the
base box. Hand-tighten them.
F
IGURE
6
Insert the knurled knobs to adjust the angle
Insert knurled knob
through this slot
9
5
Adjust the angle of the projector so that it will
project correctly. Refer to your
LP 1000 User’s
Guide
for detailed information on projection
angles, lens offset, and image sizes.
6
Tighten all the knurled knobs to secure the
projector in position.
7
Check all fasteners to make sure they are
properly tightened.
8
Connect the power cord and the cables to the
projector. (Refer to your
LP 1000 User’s Guide
for information about connecting the cables.)
F
IGURE
7
Connect the cables and thread through base box
Inverting the Image
10
When you need to remove the projector or clean
the air filter:
1
Hold the projector from underneath.
2
Remove the knurled knob that holds the pro-
jector to the mounting plate.
NOTE:
You can remove
the air filter door from the
projector while it is still
hanging on the ceiling by
carefully reaching between
the projector and base
plate and using a coin to
loosen the door.
3
Slide the projector to release it from the quick
release bolts. The projector will come off of
the mounting plate. The mounting plate will
still be attached to the base box.
4
Clean the air filter as described in your
LP
1000 Users Guide
if needed.
5
Realign the quick release bolts in the keyhole
slots on the mounting plate.
6
Fasten the knurled knob.
ADJUSTING THE IMAGE
Inverting the Image
1
Press the
menu
button on the remote or key-
pad to display the projector’s on-screen
menu.
2
Using the disk mouse on the remote or the
navigation buttons on the keypad, move the
cursor to the Controls tab to display the Con-
trols menu.
3
Move the cursor to the Ceiling Mount box.
4
Click either of the two mouse buttons to
invert the image.
Replacing the Lamp Module
You don’t need to remove the projector from the
ceiling to replace the lamp. Refer to the
LP 1000
Users Guide
for lamp removal instructions.
11
Limited Warranty
In Focus Inc. warrants that each “ceiling mount” sold hereunder will
conform to and function in accordance with the written specifications
of In Focus. Said limited warranty shall apply only to the first person
or entity that purchases the Product for personal or business use and
not for the purpose of distribution or resale. The product may contain
recycled components that are in new condition. Said warranty shall
continue for a period of one (1) year from the date of such purchase.
Proof of purchase is required for all warranty claims.
In Focus does
not warrant that the Product will meet the specific requirements of the
first person or entity that purchases the Product for personal or busi-
ness use. In Focus’ liability for the breach of the foregoing limited war-
ranty is limited to the repair or replacement of the Product or refund
of the purchase price of the Product, at In Focus’ sole option. To exer-
cise the Purchaser’s rights under the foregoing warranty, the Product
must be returned at the Purchaser’s sole cost and expense, to In Focus,
and must be protected by packaging comparable to the original pack-
aging. The Product must be accompanied by a written letter that
includes (i) proof of date of purchase, (ii) the dealer’s name, (iii) the
part number of the accessory item or the projector/panel model num-
ber, (iv) your business card information, (v) explanation of how the
item was damaged, and (vi) description of the damage and reason for
the return. Please call In Focus or your dealer for information on
where to send your case. In Focus will repair/replace and return the
case within 10 days of receipt of the item.
Warranty Limitation and Exclusion
In Focus shall have no further obligation under the foregoing limited
warranty if the Product has been damaged due to abuse, misuse,
neglect, accident, unusual physical stress, unauthorized modifica-
tions, tampering, alterations, or service other than by In Focus, causes
other than from ordinary use or failure to properly use the Product in
the application for which said Product is intended.
Disclaimer or Unstated Warranties
The warranty printed above is the only warranty applicable to this
purchase. All other warranties, express or implied, including, but not
limited to, the implied warranties of merchantability and fitness for a
particular purpose are disclaimed. There are no warranties that extend
beyond the face hereof and the foregoing warranty shall not be
extended, altered or varied except by written instrument signed by In
Focus.
Limitation of Liability
It is understood and agreed that In Focus’ liability whether in con-
tract, in tort, under any warranty, in negligence or otherwise shall not
exceed the return of the amount of the purchase price paid by pur-
chaser and under no circumstances shall In Focus be liable for special,
indirect or consequential damages or lost profits, lost revenues, or lost
savings. The price stated for the product is a consideration in limiting
In Focus’ liability. No action, regardless of form, arising out of the
agreement to purchase the product may be brought by purchaser
more than one year after the cause of action has accrued
27700B SW Parkway Avenue
Wilsonville, OR 97070-9215 USA
1-800-294-6400
Planetenweg 91
NL-2132 HL
Hoofddorp, The Netherlands
31-23-5540300
9 Raffles Place
#27-01 Republic Plaza
Singapore 048619
65-334-9005
010-0154-00 (English-Deutsch)
http://www.infocus.com
/