Craftsman 580.752200 Owner's manual

Brand: Craftsman

Model: 580.752200

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

580752200

Operator'sManual

2700 PSi MAX

2.3 GPM MAX

Model No. 580.752200

PRESSUREWASHER

CUSTOMERHELPLINE

HOURS: Non. - Fri. 8 a.m. to 5 p.m. (CT)

WAReleG

Before usingthis product, readthis

manualand follow all SafetyRules

and Operating Instructions.

I_ J7ADVERTENCJA

Antes de utilizar el producto, lea este

manualy siga todas las Reglasde

Seguridade Instrucciones de Uso.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit nut Craftsman website: www.craftsman.cnm

Part No. 205887GS Draft - (12/12/2007)

• Safety

• Assembly

• Operation

,, Maintenance

,, Parts

,, Espafiol,p. 32

WARRANTY.......................................... 2

SAFETYRULES...................................... 2-5

FEATURESANDCONTROLS.............................. 6

ASSEMBLY........................................ 7-10

OPERATION....................................... 11-15

SPECIFICATIONS..................................... 16

MAINTENANCE.................................... 17-21

STORAGE........................................... 22

TROUBLESHOOTING.................................. 23

REPLACEMENTPARTS.............................. 24-28

NOTES ............................................. 29

EMISSIONCONTROLWARRANTY..................... 30-31

ESPANOL......................................... 32-55

HOWTO ORDERPARTS........................ BACKPAGE

ONE-YEARFULLWARRAHTYONCRAFTSMAHPRESSUREWASHER

If this pressurewasher fails dueto a defectin material or workmanship within one year from the dateof purchase,return it to

any Searsstore, other Craftsman outlet, or SearsParts & RepairCenterin the UnitedStates or Canadafor free repair (or

replacementif repair proves impossible).

All warranty coverageapplies for only 90 days from dateof purchaseif this pressure washer is ever usedfor commercial or

rentalpurposes.

This warranty gives you specific legal rights, and you mayalso haveother rights which vary from stateto state.

Sears, Roebuck and Co., Hoffman Estates, IL 60178

Sears Canada Inc., Toronto, Ontario, Canada M5B 288

,_ Thisisthe safetyalert symbol.It isusedto alert youtopotentialpersonalinjuryhazards.Obeyall safetymessages

thatfollow thissymboltoavoid possibleinjuryor death.

_Read this manualcarefully and becomefamiliar

with yourpressurewasher. Knowits applications,

its limitations, and any hazardsinvolved.

Thesafety alert symbol (_.) is usedwith a signal word

(DANGER,CAUTION,WARNING),a pictorial and/or a safety

messageto alert you to hazards.BANGERindicatesa hazard

which, if not avoided, willresult in deathor serious injury.

WARNINGindicates a hazardwhich, if not avoided, could

result in deathor serious injury. CAUTIONindicatesa hazard

which, if not avoided, might result in minor or moderate

injury. NOTICEindicatesa situation that could result in

equipment damage. Follow safety messagesto avoid or

reducethe risk of injury or death.

Hazard Symbolsand Meaninos

ToxicFumes Kickback

2 5-

SlipperySurface Fall

Fire

Explosion

ElectricalShock

FluidInjection

Operator'sManual

MovingParts FlyingObjects

HotSurface

WARHJNG

Theengineexhaustfromthisproductcontains

chemicalsknowntotheStateof California tocause

cancer,birthdefects,or otherreproductiveharm.

WARHJHG

Runningengine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathingcarbon monoxide can cause headache,

_ atigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

Some chemicals or detergents may be harmful if

inhaled or ingested, causing severe nausea,

fainting, or poisoning.

* OperatepressurewasherONLYoutdoors.

Keepexhaustgasfromenteringaconfinedareathrough

windows,doors,ventilationintakes,or otheropenings.

DONOTstartor runengineindoorsor in anenclosedarea,

evenif windowsanddoorsareopen.

Usea respiratoror maskwheneverthereisa chancethat

vaporsmaybeinhaled.

Readall instructionswith masksoyouarecertainthemaskwill

providethenecessaryprotectionagainstinhalingharmful

vapors.

WARHIHG

_¢ isk of electrocution.

Contactwith power source can causeelectric

shock or burn.

* NEVERspraynearpowersource.

WARHIHG

Fueland its vapors are extremely flammable and

explosive.

Fireor explosion cancause severe burns or

death.

WHENADDINGORDRAININGFUEL

* TurnpressurewasherOFFandletit coolatleast2minutes

beforeremovingfuelcap.Loosencapslowlyto relievepressure

in tank.

Fillor drainfueltankoutdoors.

DONOToverfilltank.Allowspaceforfuelexpansion.

Iffuelspills,waituntilit evaporatesbeforestartingengine.

Keepfuelawayfromsparks,openflames,pilotlights,heat,and

otherignitionsources.

DONOTlighta cigaretteorsmoke.

WHENSTARTIN6EQUIPMENT

* Ensuresparkplug,muffler,fuelcap,andaircleanerarein

place.

. DONOTcrankenginewith sparkplugremoved.

WHENOPERATINGEQUIPMENT

* DONOTtip engineor equipmentat anglewhichcausesfuelto

spill.

. DONOTsprayflammableliquids.

WHENTRANSPORTINGORREPAIRINGEQUIPMENT

* Transport/repairwithfueltank EMPTYor withfuelshutoffvalve

OFF.

. Disconnectsparkplugwire.

WHENSTORINGFUELOREQUIPMENTWITH FUELIN TANK

* Storeawayfromfurnaces,stoves,waterheaters,clothes

dryers,or otherappliancesthathavepilotlightor otherignition

sourcebecausetheycanignitefuelvapors.

WARHJHG

Startercord kickback(rapid retraction) can result

in bodily injury. Kickbackwill pull handand arm

_,_.< toward engine faster than you can let go.

Brokenbones, fractures, bruises, or sprains

could result.

• NEVERpull starter cord without first relieving spray gun

pressure.

. When starting engine, pull cord slowly until resistance is felt

andthen pull rapidly to avoid kickback.

• After eachstarting attempt, where enginefails to run, always

point spray gun in safe direction, press red button and squeeze

spray gun trigger to releasehigh pressure.

• Firmly grasp spray gun with both handswhen using high

pressure spray to avoid injury when spray gun kicks back.

WARHIHG

Useof pressure washer cancreate puddles and

slippery surfaces.

Kickbackfrom spray gun cancause you to fall.

. Operatepressure washer from astable surface.

• The cleaningarea should haveadequateslopes and drainageto

reducethe possibility of a fall due to slippery surfaces.

. Be extremelycareful if you must usethe pressure washer from

a ladder,scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARHIHG

_ Contact with muffler result in serious

area can

burns.

_ Exhaustheat/gases can ignite combustibles,structures or damagefuel tank causing a fire.

• DO NOTtouch hot parts and AVOID hot exhaust gases.

. Allow equipment to cool before touching.

• Keepat least 5feet (152 cm) of clearanceon all sides of

pressure washer including overhead.

• Codeof FederalRegulation (CFR)Title 36 Parks, Forests,and

Public Property require equipment powered by an internal

combustion engine to have aspark arrester, maintained in

effective working order, complying to USDAForestservice

standard 5100-1C or later revision. Inthe State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other statesmay havesimilar laws.

WARHIHG

The high pressure stream of water that this

equipment produces can cut through skin and its

_ nderlying tissues, leading to serious injury and

)ossible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• DONOTallow CHILDRENto operate pressure washer.

. NEVERrepair high pressure hose. Replaceit.

• NEVERrepair leaking connections with sealantof any kind.

Replaceo-ring or seal.

• NEVERconnect high pressure hoseto nozzle extension.

. Keephigh pressure hoseconnectedto pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, pressred button

and squeezespray gun trigger to releasehigh pressure, every

time you stop engine.

• NEVERaim spray gun at people, animals, or plants.

. DONOTsecure spray gun in open position.

• DO NOTleavespray gun unattendedwhile machine is running.

. NEVERusea spray gun which does not have atrigger lock or

trigger guard in place andin working order.

. Always be certain spray gun, nozzlesand accessories are

correctly attached.

WARHIHG

_ Unintentionalsparking can result in fire or

_¢ electric shock.

WHENADJUSTINGORMAKINGREPAIRSTOYOUR

PRESSUREWASHER

. Disconnectthe sparkplug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHENTESTINGFORENGINESPARK

. Use approved sparkplug tester.

• DONOTcheck for sparkwith spark plug removed.

WARHJHG

Starter and other rotating parts canentangle

hands, hair, clothing, or accessories.

* NEVERoperate pressure washer without protective housing or

covers.

* DO NOTwear loose clothing, jewelry or anything that may be

caught in the starter or other rotating parts.

* Tie up long hair and remove jewelry.

WARNING

Risk of eye injury.

" _ JSpraycan splash back or propel objects.

Alwayswear safety goggles when using this equipment or in

vicinity of where equipment is in use.

Beforestarting the pressure washer, be sureyou are wearing

adequatesafety goggles.

NEVERsubstitute safetyglasses for safety goggles.

NOTICE

High pressure spray may damage fragile items including

lass.

DO NOTpoint spray gun at glasswhen using red (0°) nozzle.

NEVERaim spray gun at plants.

NOTICE

Improper treatment of pressure washer can damage it and

shorten its life.

Ifyou have questions about intended use, ask dealeror contact

Sears.

NEVERoperate units with broken or missing parts, or without

protective housing or covers.

DONOT by-pass any safety device on this machine.

DONOTtamper with governed speed.

DONOToperate pressure washer above rated pressure.

DONOT modify pressurewasher in any way.

Before starting pressure washer in cold weather, check all parts

of the equipmentto besure ice has not formed there.

NEVERmove machineby pulling on hoses. Use handle

provided on unit.

Checkfuel system for leaksor signs of deterioration, such as

chafed or spongy hose,loose or missing clamps, or damaged

tank or cap. Correct all defects beforeoperating pressure

washer.

This equipment is designedto be used with Searsauthorized

parts ONLY.If equipment is used with parts that DO NOT

comply with minimum specifications, userassumes all risks

and liabilities.

KNOWYOURPRESSUREWASHER

_Head the Operator'sManual and safety rulesbefore operatingyourpressurewasher.

Comparethe illustrations with your pressurewasher to familiarizeyourself with the locations of various controls and

adjustments. Savethis manualfor future reference.

• • • (_)

A- Spray Gun-- Controlsthe application of water onto

cleaningsurfacewith trigger device.Includestrigger lock.

B - PrecisienSprayTM Nozzles-- general,max,jet flush, jet

soap, and fansoap nozzlesfor various high pressure

cleaning applications.

C- Accessory Tray-- Provides convenientstorage for

accessories,such as gun, nozzles,etc.

D - Recoil Starter -- Used for starting the engine manually.

E - Fuel Tank-- Fill tank with regular unleadedfuel. Always

leaveroom for fuel expansion.

F - Air Filter -- Protects engine by filtering dust and debris

out of intake air.

G - Throttle Lever-- Setsengine in starting modefor recoil

starter and stops a running engine.

H - Pump -- Developshigh pressure.

J - High PressureOutlet-- Connectionfor high pressure

hose.

K - Water Inlet -- Connectionfor garden hose.

L - AutomaticCool DownSystem-- Cycleswater through

pump whenwater reaches125°-155°F. Warm water will

dischargefrom pump onto ground. This system prevents

internal pump damage.

M - Bottle[}racket-- Cleaningsolution bottle fits in wire

form bracket here.Concentratebottle not included.

N - Oil Fill/Dipstick -- Check,add and drain engine oil here.

P - NozzleExtensionwith QuickConnect-- Allows you to

switch between five different nozzles.

Q - HoseWrapand High Pressure Hose-- Hosewrap

provides easytransport and handling of the high pressure

hose. Connectone end of hoseto water pump and the

other end to spray gun.

H - FoldDownHandle -- Handleand accessorytray fold flat

atop cold engine for space-saving storage.

S - Project Pro_ PerfectiVIWMSiphon-- Mixesconcentrate

with pressurewasher spray.

Items Not Shown:

DetergentSiphoning Tube/Filter-- Useto siphon pressure

washer safe detergentsinto the low pressure stream.

DataTag (near rear of base plate) -- Provides modeland

serial number of pressure washer. Pleasehavethese readily

availableif calling for assistance.

SafetyGoggles-- Always usethe enclosedsafety goggles

when running your pressure washer.

Warning/OperatinginstructionsTag-- identifies hazards

and proper procedureto start/stop pressurewasher.

Your pressure washer requires some assembly and is ready

for useonly after it has been properly servicedwith the

recommendedoil and fuel.

If you haveany problemswith the assemblyof your

pressurewasher, please call the pressurewasher heipline

at 1-800-222-3135.

5. Add fuelto fuel tank.

6. Connectpressure hoseto spray gun and pump.

7. Connectwater supply to pump.

8. Attach nozzleextension to spray gun.

9. Select/attachquick connect nozzleto nozzleextension.

UNPACKTHEPRESSUREWASHER

1. Removeeverything from carton exceptpressure washer.

2. Opencarton completely bycutting eachcorner from top

to bottom.

Attach Handle, Accessory Tray, RopeGuide, and

Hose Wrap and Bottle Bracket

1. Placehandle (A) onto handlesupports (B) connectedto

main unit. Make sure holes (C) in handlealign with holes

3. Removepressure washer from carton.

CARTONCONTENTS

Checkall contents, if any parts are missing or damaged,call

the pressure washer helpline at 1-800-222-3136.

* Main Unit

* Handle

* AccessoryTray

* High PressureHose

* Spray Gun

* NozzleExtensionwith Quick ConnectFitting

* Oil Bottle

* HoseWrap

* Parts Bag (which includes the following):

* Operator's Manual

* Owner's Registration Card

* SafetyGoggles

* Bottle BracketWireform

. PerfectMixTMSiphoning Unit/Hose

* StandardSiphoning Hose

. Bagcontaining 5 PrecisionSprayTM Nozzles

* HandleFasteningHardwareKit (whichincludes):

. HandleBolts (2)

. CarriageBolt (1)

* Plastic Knobsfor Handle(2)

* RopeGuide (1)

* Plastic Knob (2)

* TreeClips (4)

Becomefamiliar with eachpiecebefore assemblingthe

pressure washer. Identify all contents with the illustration on

page 6. If any parts are missing or damaged,callthe

pressure washer helpline at 1-800-222-3136.

ASSEMBLINGPRESSUREWASHER

Your Craftsmanpressure washer will need assembly before

operation:

1. Fill out and send in registration card.

2. Attach handleand accessorytray.

3. Connectdetergent siphon hoseto pump.

4. Add oil to engine crankcase.

Insert handle carriagebolts (D)through holes from

inside of unit and attacha plastic knob (E)from outside

of unit. Tighten by hand. Byloosening both knobs to the

middle section of the attachment bolt, the upper handle

can fold forward to store flat atop the cold engine. Note:

DONOTfold the handle down while the engine is hot.

Placeaccessorytray (F) over holes (G) on handle

(viewing from back of unit). Pushthe tree clips (N) into

the holes until they sit flat againstthe accessorytray.

Insert PrecisionSprayTM nozzlesand other supplied

accessories in spacesprovided in accessorytray. See

How to UseAccessory Tray.

Attach rope guide (A) through handlewith plastic knob

(B). Tighten by hand. Routeengine recoil rope through

guide.

Align hosewrap (C)to the back side of accessorytray.

Locate notch with "unlock"icon (D) on hosewrap.

Position notch attop with hosewrap in vertical position.

Clips in the back of accessorytray should slide into the

grooves on the inside surface of hose wrap. Slide hose

wrap on back of accessorytray and rotate 1/8 turn until

"locked"icon (E) is in vertical position. Hosewrap is

easily removed from the accessorytray for wrapping and

unwrapping ofthe high pressure hose. A clip to secure

the hose on the reel makesit easyto wrap the hose

while it is detachedfrom the accessorytray.

Attach bottle bracket (F)to handle with carriage bolt (G)

and black plastic knob (H). Tighten by hand.

2-1N-1SIPHOHSYSTEM

Thepressure washer is equipped with two detergent

siphoning hoses.

Standard Clear Siphon Tube

Cleartube with filter:

Whenusingtheclearsiphontube,dilute

1partconcentrateto 16partswater

(4 ozof standardconcentratemakes

1/2gaflonofmix.)

Project Pro PerfectMiW_Siphon

Bluetube with blue bottle cap:

WhenusingthebluePerfectMixTM siphon,

usetheconcentratestraightfrom thebottle

(OnequartbottleofPerfectMixTM concentrate

makes4.25gaflonsofsoapspray.)

AttachProject Pro®PerfectMix" Siphonto Pump

Attach the hose end of the blue Project Pro®PerfectMixTM

Siphon (J)to the barbed hose fitting (K) on the pump.

Attach PerfectMix,. Detergent Siphon

to Concentrate BottJe

PlaceProject Pro®PerfectMixTM bottle (not included) in the

wire-form bracket on the handle.Removecap from bottle

and insert the Project Pro®PerfectMixTM Siphon (M). Screw

the siphon unit to the top of the bottle (N). Usethe clip on

the cap (M) to snapsiphon to wire form bracketwhen siphon

is not in a concentrate bottle.

AddEngineOil

1. Placepressure washer on a flat, levelsurface.

2. Cleanareaaround oil fill and removeyellow oil fill

cap/dipstick.

3. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening.

NOTICE

Improper treatment of pressure washer can damageit and

shorten its life.

DONOTattemptto crankor starttheenginebeforeit hasbeen

properlyservicedwiththerecommendedoil.Thismayresultin

anenginefailure.

4. Replaceoil fill cap/dipstick and fully tighten.

AddFuel

Fuelmustmeet theserequirements:

• Clean,fresh, unleadedgasoline.

• A minimum of 87 octane/B7AKI (91 RON).High altitude

use, seeHigh Altitude.

• Gasolinewith upto 10% ethanol (gasohol) or up to 15%

MTBE (methyltertiary butyl ether) is acceptable.

HI:ITICE

Avoid pressure washer damage.

Failureto follow Operator's Manualfor fuel

recommendations voids warranty.

DONOTuseunapprovedgasolinesuchasE85.

DONOTmixoil in gasoline.

DONOTmodifyengineto runon alternatefuels.

To protect the fuel system from gum formation, mix in a fuel

stabilizer whenadding fuel. SeeStorage.All fuel is not the

same. If you experiencestarting or performanceproblems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operateon gasoline. The

emission control system for this engine is EM (Engine

Modifications).

WARHING

f_ Fueland its vapors are extremely flammable and

explosive.

Fireor explosion can causesevere burns or

death.

WHENADDINGFUEL

* TurnpressurewasherOFFandletit coolatleast2minutes

beforeremovingfuelcap.Loosencapslowlyto relievepressure

in tank.

. Fillfueltank outdoors.

. DONOToverfilltank.Allowspacefor fuelexpansion.

* If fuelspills,waituntilit evaporatesbeforestartingengine.

* Keepfuelawayfromsparks,openflames,pilotlights,heat,and

otherignitionsources.

. DONOTlighta cigaretteor smoke.

1. Cleanarea around fuel fill cap, remove cap.

2. Slowly add regular unleadedfuel (A) to fuel tank (U). Be

careful notto overfill. Allow about 1.5" (4 cm) (g) of tank

spacefor fuel expansion.

3. Installfuel cap and waitfor any spilledfuelto evaporate.

CAUTION!Alcohol-blended fuels (calledgasohol, ethanol or

methanol) can attract moisture, which leadsto separation and

formation of acids during storage.Acidic gascan damagethe

fuel system of an enginewhile in storage.

Toavoid engine problems, the fuel system should betreated

with a fuel preserver or emptied before storage of 30 days or

longer. If adding a fuel preserver,fill the fuel tank with fresh

fuel. If only partially filled, air in the tank will promote fuel

deterioration during storage. If fuel preserver is not used,

drain the fuel tank, start the engineand let it run until the fuel

linesand carburetor are empty. Usefresh fuel next season.

SeeStoragefor additional information.

NEVERuse engine or carburetor cleaner products in the fuel

tank as permanent damagemay occur.

HighAItitMe

At altitudes over5,000 feet (1524 meters), a minimum

85 octane/ 85 AKI (89 RON)gasoline is acceptable.To

remainemissions compliant, high altitude adjustment is

required. Operationwithout this adjustment will cause

decreasedperformance, increased fuel consumption, and

increasedemissions. Seea qualified Searsdealerfor high

altitude adjustment information. Operationof the engine at

altitudes below 2,500 feet (762 meters)with the high altitude

kit is not recommended.

Connect Hose and Water Supply to Pump

[ NOTICE

DONOTrun the pump without the water supply connected

and turned on.

t amageto equipmentresultingfrom failureto followthisinstructionwillvoidwarranty.

NOTE:Removeand discardthe shipping caps from the

pump's high pressure outlet and water inlet beforeattaching

hoses.

1. Uncoil high pressure hose and attach one end of hoseto

baseof spray gun. Tighten by hand.

WARNING

Thehigh pressurestream of water that this

_ quipment produces cancut through skin and its

underlyingtissues, leadingto serious injury and

)ossible amputation.

. NEVERconnecthighpressurehoseto nozzleextension.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

Alwaysbecertainspraygun,nozzlesandaccessoriesare

correctlyattached.

2. Attach other end of high 3ressurehoseto high pressure

outlet on pump. Tighten by hand.

Beforeconnectinggarden hoseto water inlet, inspect

inlet screen (A). Cleanscreenif it contains debris or have

it replacedif damaged•DONOTrun pressurewasher if

inlet screenis damagedor missing.

4. Run water through garden hose for 30 secondsto flush

it of debris• Turn off water•

IMPORTANT:DONOTsiphon standing water for the water

supply• UseONLYcold water (less than IO0°F).

5. Connectgarden hose (not to exceed50 feet in length) to

water inlet•Tighten by hand•

NOTICE

Using a OneWay Valve(vacuum breakeror check valve)at

pump inlet cancause pump or inlet connector damage•

ThereMUSTbeatleasttenfeetofunrestrictedgardenhose

betweenthe pressurewasherinletandanydevice,suchasa

vacuumbreakeror checkvalve•

Damageto equipmentresultingfrom failuretofollowthis

instructionwillvoidwarranty•

6. Turn ONthe water, pressred button (B) on the gun and

squeezethe trigger to purgethe pump system of air and

impurities•

WARHJHG

Riskof eyeinjury•

• _ JSpraycansplash back or propel objects•

Alwayswearsafetygoggleswhenusingthis equipmentor in

vicinityof whereequipmentisin use.

Beforestartingthepressurewasher,besureyouarewearing

adequatesafetygoggles•

NEVERsubstitutesafetyglassesfor safetygoggles•

ChecklistBefore StartingEngine

Reviewthe unit to ensureyou have performed all of the

following:

1. Besure to read SafetyRules and Operationsections

before usingthe pressure washer•

2. Makesure handle is in placeand secure•

3. Checkthat oil has beenadded to proper levelin engine

crankcase•

4. Add proper fuelto fuel tank•

5. Checkfor proper hoseconnections (high pressure and

water supply) and that there are no kinks, cuts, or

damageto the high pressure hose•

6. Provideproper water supply (not to exceedIO0°F).

HOWTOUSEYOURPRESSUREWASHER

If you haveany problems operatingyour pressure washer,

pleasecallthe pressure washer helpline at 1-808-222-3136.

Pressure Washer Location

PressureWasherClearance

WARNING

_ Exhaustheat/gases can ignitecombustibles,

structures or damagefuel tank causing a fire.

• Keepatleast5ft. (152cm)clearanceonall sidesofpressure

washerincludingoverhead.

Placepressure washer outdoors in an areathat will not

accumulate deadlyexhaustgas. DONOTplacepressure

washer where exhaustgas (A) could accumulateand enter

inside or be drawn into a potentially occupied building.

Ensureexhaustgas is kept awayfrom any windows, doors,

ventilation intakes, or other openingsthat can allow exhaust

gasto collect in a confined area. Prevailingwinds and air

currents should be taken into considerationwhen positioning

_ressurewasher.

WARHIHG

Runningengine gives off carbon monoxide, an

_ dorless, colorless, poison gas.

Breathingcarbon monoxide can causeheadache,

fatigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

. OperatepressurewasherONLYoutdoors.

• Keepexhaustgasfromenteringaconfinedareathrough

windows,doors,ventilationintakes,or otheropenings.

• DONOTstartorrunengineindoorsor in anenclosedarea,

evenif windowsanddoorsareopen.

To Start Your Pressure Washer

To start your engine-powered pressurewasher for the first

time, follow these instructions step-by-step. This information

also applies wheneveryou start the engine after you havelet

the pressure washer sit idle for at least a day.

1. Placepressure washer outside near an water source

capableof supplying water at a flow rategreater than

3.3 gallons per minute and no less than 20 PSIat

pressurewasher end of garden hose.

2. Checkthat high pressure hose istightly connectedto

spray gun and pump. SeeAssemblyfor illustrations.

3. Makesure unit is in a levelposition.

4. Connectgarden hoseto water inlet on pressure washer

pump.

[ NOTICE

pO NOT the without the connected

run

pump

water

supply

and turned on.

L amageto equipmentresultingfrom failureto followthis

instructionwillvoidwarranty.

5. Turn ONthe water,press red button on the gun and

squeezethe trigger to purge the pump system of air and

impurities.

6. Attach nozzleextension to spray gun. Tighten by hand.

ChoosePrecisionSprayTMnozzleyou want to use, pull

back on collar of nozzleextension, insert nozzle and

releasecollar. Tug on nozzleto make sure it is securely

in place.See How to Use PrecisionSpraSMNozzle

System.

8. Move throttle lever (A) to "Fast" position, shown here as

a rabbit.

9. Move choke lever (B) to "Choke" position.

NOTE:Fora warm engine, be surethe choke lever is in the

"Run" position.

IMPORTANT:Beforestarting the )ressure washer, be sure

you are wearing adequatesafetygoggles.

WARHIHG

Riskof eyeinjury.

_Spray cansplash back or propel objects.

Alwayswearsafetygoggleswhenusingthis equipmentor in

vicinityof whereequipmentisin use.

Beforestartingthe pressurewasher,besureyouarewearing

adequatesafetygoggles.

NEVERsubstitutesafetyglassesfor safetygoggles.

10. Whenstarting engine, position yourself as

recommended, grasp handle and pull recoil starter

lightly until you feel some resistance,then pull briskly.

11. Return recoil starter slowly. DONOTlet rope "snap

back" against starter.

12. Whenengine starts, slowly move choke leverto "Run"

position, asengine warms, if engine falters, move choke

leverto "Choke" position, then to "Run" position.

13. After eachstarting attempt, where engine fails to run,

alwayspoint gun in safe direction and squeezespray

gun trigger to releasehigh pressure. Movechoke lever

to "Choke" position, and repeatsteps 10through 12.

WARHIHG

Starter cord kickback(rapid retraction) can result

in bodily injury. Kickbackwill pull handand arm

_ toward enginefaster thanyou canlet go.

Brokenbones, fractures, bruises, or sprains

could result.

* NEVERpullstartercordwithoutfirst relievingspraygun

pressure.

Whenstartingengine,pullcordslowlyuntilresistanceisfelt

andthenpullrapidlyto avoidkickback.

Aftereachstartingattempt,whereenginefailsto run,always

pointspraygunin safedirectionpressredbuttonandsqueeze

sprayguntriggerto releasehighpressure.

Firmlygraspspraygunwith bothhandswhenusinghigh

pressuresprayto avoidinjurywhenspraygunkicksback.

14. If enginefails to start after six pulls, movechoke leverto

"Run" position, and repeatsteps 10 through 12.

NOTE:Always keepthe throttle lever in the "Fast" position

when operatingthe pressure washer.

WARHIHG

Thehigh pressurestream of water that this

equipment produces cancut through skin and its

,p_ underlyingtissues, leadingto serious injury and

)ossible amputation.

Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected,

which can cause injury.

, DONOTallowCHILDRENtooperatepressurewasher.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• NEVERaimspraygunatpeople,animals,or plants.

, DONOTsecurespraygun inopenposition.

• DONOTleavespraygununattendedwhilemachineis running.

, NEVERusea spraygunwhichdoesnothaveatriggerlockor

triggerguardin placeandinworkingorder.

• Alwaysbecertainspraygun,nozzlesandaccessoriesare

correctlyattached.

WARHIHG

_ Contact with muffler result in serious

area can

burns.

,_ Exhaustheat/gases can ignite combustibles,structures or damagefuel tank causing a fire.

DONOTtouchhotpartsandAVOIDhotexhaustgases.

* Allowequipmenttocoolbeforetouching.

Keepatleast5 feet(152cm) ofclearanceonall sidesof

pressurewasherincludingoverhead.

* Codeof FederalRegulation(CFR)Title36Parks,Forests,and

PublicPropertyrequireequipmentpoweredbyaninternal

combustionengineto haveasparkarrester,maintainedin

effectiveworkingorder,complyingto USDAForestservice

standard5100-1Cor laterrevision.IntheStateof Californiaa

sparkarresterisrequiredundersection4442oftheCalifornia

Publicresourcescode.Otherstatesmayhavesimilarlaws.

How to Stop Your Pressure Washer

1. Releasespray gun trigger and letengine idle for two

minutes.

2. Movethrottle to SLOWposition,then STOPposition.

3. ALWAYSpoint spray gun in a safe direction, push red

button and squeezespray gun trigger to releaseretained

high water pressure.

iMPORTANT:Spraygun traps high water pressure,even

when engine is stopped and water is disconnected.

WARHIHG

The high pressure stream of water that this

equipment produces cancut through skin and its

_ nderlying tissues, leadingto serious injury and

_ossibleamputation.

Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected,

which can cause injury.

. Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirectionpressredbuttonand

squeezesprayguntrigger,to releasehighpressure,everytime

you stopengine.

Howto UseAccessoryTray

The unit is equipped with an accessorytray with placesto

store your spray gun, nozzleextensionand quick connect

PrecisionSprayTM nozzles.Thereis also a detachablehose

wrap at the back of the accessorytray to hold your high

pressure hose.

1. Placenozzleextensioninclip on backof accessorytray.

2. Placespray gun through hole on accessorytray on right

side of unit.

3. Insert multi-colored nozzlesin spacesprovided in

accessorytray.

4. Wrap high pressure hose on hose wrap then attach hose

wrap to back of accessorytray.

5. Hook provided on back of accessorytray for safely

storing safety goggles.

How to Use PrecisionSprayTM Nozzle System

Thequick-connect on the nozzleextensionallows you to

switch between five different PrecisionSprayTM system

nozzles. PrecisionSprayTM nozzlescan be changedwhile

pressure washer is running oncespray gun trigger lock is

engaged.

Feflowthese instructionsto changePrecisionSprayTM

flozzJes:

1. Pull backcollar on quick-connect and pull current

PrecisionSprayTM nozzleoff. Store PrecisionSprayTM

nozzlesin holder provided on the accessorytray.

WARHIHG

Thehigh pressure stream of water that this

_ equipment produces can cut through skin and itsiundery ng tissues, leadingto serious injury and

jpossible amputation.

* NEVERexchangenozzleswithoutthetriggerlockedonthe

spraygun.

* DONOTtwist nozzleswhilespraying.

2. Select desired PrecisionSprayTM nozzle:

. Selectorange general PrecisionSprayTM nozzlefor all

purpose cleaning. Cleansvinyl siding, brick patios,

concrete driveways and other surfaces.

• Selectred max PrecisionSprayTM nozzlefor maximum

cleaning.Greatfor cleaningstubbornstains, including

grease,tar, wax,and otherhardto removestains.

Selectcyan jet flush PrecisionSprayTM nozzlefor

quick high flow clean up and long reachcleaning of

second story siding and windows.

JET FLUSH

* Select magentajet soap PrecisionSprayTM nozzleto

launch soapto second story siding and windows.

Select black fan soap PrecisionSprayTM nozzlefor

generalcleaning. Greatfor applying soapto

vehicles, boats, driveways, decks,and patios.

FAN SOAP

3. Pull backon collar,insert newPrecisionSprayTM nozzle

and releasecollar.Tug on nozzleto makesureit is securely

in place.

UsageTips

* Formost effective cleaning, keepPrecisionSprayTM nozzle

from 8 to 24 inches (20 to 61 cm) awayfrom cleaning

surface.

* If you get PrecisionSprayTM nozzletoo close, especially

usinga high pressure nozzle,you may damagesurface

being cleaned.

, DONOTget closer than 6 inches (15 cm) when cleaning

tires.

2-IN-1 SIPHONSYSTEM

Cleaning and Applying Detergent with

the Project Pro®PerfectMix TM Siphon

CAUTIOH

Chemicalscan causebodily injury, and/or property

damage.

NEVERusecausticliquidwith pressurewasher.

UseONLYpressurewashersafedetergents/soaps.Followall

manufacturersinstructions.

To apply undiluteddetergent using

the blue PerfectMixTM siphen,

felJow thesesteps:

1. Reviewuse of PrecisionSprayTM nozzles.

2. Attach PerfectMixTM siphon hoseto

pump and PerfectMixTM concentrate

bottle.

3. Make sure fan soap (black) or jet soap

nozzle(magenta)is installed.

NOTE:Detergentcannot be applied with the

high pressure nozzles(Cyan,Orangeor Red).

4. Makesure garden hose is connectedto water inlet.

Checkthat high pressure hose is connectedto spray gun

and pump. Turn on water.

NOTICE

You must attachall hosesbefore you start the engine.

Startingtheenginewithoutallthehosesconnectedandwithout

thewaterturnedONwill damagethepump.

Damageto equipmentresultingfrom failureto followthis

instructionwillvoidwarranty.

5. Start engine following instructions How to Start Your

Pressure Washer.

6. Placethreadedend of detergent siphoning tube into

detergentcontainer. Tighten by hand.

7. Apply detergentto a dry surface, starting at lower

portion of areato be washed and work upward, using

long, even, overlappingstrokes.

8. Allow detergentto "soak in" for 3-5 minutes before

washing and rinsing. Reapplyas neededto prevent

surface from drying. DONOTallow detergent to dry on

(preventsstreaking).

Cleaning and Applying Detergent with

the Standard Clear Siphon

To apply diluted detergentusingthe

standard cJearsiphontube,

felJew these steps:

1. Reviewuseof

PrecisionSprayTM nozzles.

2. Attach clear siphon hoseto pump.

3. Mix detergent solution as required by job.

4. Placesmall filter end of clear siphoning tube into

container with diluted solution as described above.

NOTICE

Contact with the hot muffler can damagedetergent

siphoning tube.

Wheninsertingthesiphonintoa detergentsolutionbottle,

routethetubesoasto keepit from inadvertentlycontactingthe

hotmuffler.

NOTE:Makesure the filter is fully submerged in fluid while

applying solution.

5. Makesure fan soap (black) or jet soap nozzle(magenta)

is installed.

NOTE:Detergentcannot be applied with the high pressure

nozzles(Cyan,Orangeor Red).

6. Makesure garden hose is connectedto water inlet.

Checkthat high pressure hose is connectedto spray gun

and pump. Turn on water.

7. Start engine following instructions How to Start Your

Pressure Washer.

8. Applydetergenttoadrysurface,startingatlower

portionofareatobewashedandworkupward,using

long,even,overlappingstrokes.

9. Allowdetergentto"soakin"for3-5minutesbefore

washingandrinsing.Reapplyasneededtoprevent

surfacefromdrying.DONOTallowdetergenttodryon

(preventsstreaking).

IMPORTANT:Youmustflushthedetergentsiphoningsystem

aftereachusebyplacingthefilterintoabucketofclean

water,thenrunthepressurewasherinlowpressurefor1-2

minutes.

PressureWasherRinsing

ForRinsing:

1. Removesoap nozzlefrom nozzleextension.

2. Selectand install desiredhigh pressure nozzlefollowing

instructions How to Use Precision SprayNozzleSystem.

3. Keepthe spray gun a safe distance from the areayou

plan to spray.

WARHIHG

spray gun can cause you

Kickbackfrom to fall.

, Operatepressurewasherfrom astablesurface.

• Beextremelycarefulif youmustusethepressurewasherfrom

a ladder,scaffolding,or anyothersimilarlocation.

, Firmlygraspspraygunwith bothhandswhenusinghigh

pressuresprayto avoidinjurywhenspraygunkicksback.

4. Apply a high pressure spray to a small area,then check

the surfacefor damage.If no damageis found, it is okay

to continue cleaning.

Start at the top of the areato be rinsed, working down

with same overlapping strokes asyou usedfor washing

and applying detergent.

Cleaning DetergentSiphoning Tube

If you usedthe clear detergent siphoning tube, you must

flush it with cleanwater beforestopping the engine.

1. Placedetergent siphoning tube/filter in a bucketfull of

clean water.

2. Removehigh pressure nozzlefrom nozzleextension.

3. Selectand install a soap nozzlefollowing instructions

How to Use PrecisionSpray'_NozzleSystem.

4. Flushfor 1-2 minutes.

5. Shut off engine following instructions How to Stop

Pressure Washerand turn off water supply.

6. ALWAYSpoint spray gun in a safe direction push red

button and squeezespray gun trigger to releaseretained

high water pressure.

WARHIHG

Thehigh pressure stream of water that this

,p_ jequipment produces can cut through skin and its

iunderlying tissues, leadingto serious injury and

ipossible amputation.

, NEVERexchangenozzleswithoutthetriggerlockedonthe

spraygun.

, DONOTtwist nozzleswhilespraying.

iMPORTANT:Spraygun traps high water pressure,even

when engine is stopped and water is disconnected.

Automatic Cool Down System (Thermal ReJief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun,

circulating water in the pump can reachtemperatures above

125°F.Thesystem engagesto cool the pump by discharging

the warmwater ontothe ground.

EHGINETECHNICALJNFORMATIOH PRODUCTSPECIFICATiOHS

This is a single cylinder, overheadvalve (OHV),air cooled

engine, it is a low emissions engine.

Inthe Stateof California, Model 120000 enginesare certified

by the California Air Resources Boardto meet emissions

standardsfor 125 hours. Such certification does not grant

the purchaser, owner or operator of this engine any

additional warranties with respectto the performance or

operational life of this engine.Theengine is warranted solely

according to the product and emissions warranties stated

elsewherein this manual.

Power Ratings

Thegross power rating for individual gas engine models is

labeledin accordancewith SAE(Societyof Automotive

Engineers)codeJ1940 (Small Engine Power & Torque

Rating Procedure),and rating performance hasbeen

obtained andcorrected in accordancewith SAEJ1995

(Revision2002-05). Torquevalues are derived at3060 RPM;

horsepower values are derivedat 3600 RPM.Actual gross

engine power will be lower and is affected by, among other

things, ambient operating conditions and engine-to-engine

variability. Givenboth the wide array of products on which

enginesare placedand the variety of environmental issues

applicableto operatingthe equipment, the gas engine will not

developthe ratedgross power when used in a given pieceof

power equipment (actual "on-site"or net power). This

difference is due to a variety of factors including, but not

limited to, accessories (air cleaner, exhaust,charging,

cooling, carburetor, fuel pump, etc.), application limitations,

ambient operating conditions (temperature,humidity,

altitude), and engine-to-engine variability. Dueto

manufacturing and capacity limitations, Briggs & Stratton

maysubstitute an engine of higher ratedpower for this

Seriesengine.

This pressurewasher is rated in accordanceto the Pressure

Washer Manufacture Association (PWMA) standard PW101

(Testingand Rating Performanceof PressureWashers).

Pressure Washer Specifications

Max Outlet Pressure ....................... 2,700 PSi

Max Flow Rate............................. 2.3 GPM

DetergentMix ........................ Useasdirected

Water SupplyTemperature .......... Not to exceed IO0°F

Shipping Weight ............................. 71 Ibs.

Engine Specifications

Bore ................................. 2.69 in. (68mm)

Stroke ............................... 2.04 in. (52mm)

Displacement ........................ 11.57in. (190 cc)

SparkPlug

Type:..................... Briggs & Stratton 491055S

SetGapTo: ...................... O.020inch(0.50ram)

ArmatureAir Gap: ........... 0.006-0.014in.(O.15-O.36mm)

Valveclearancewithvalvespringsinstalledand piston1/4in.

(6 ram)pasttopdeadcenter(checkwhenengineiscold).

Intake.................... 0.004-0.006in.(0.10-0.15mm)

Exhaust .................. 0.004-0.008in.(0.10-0.20mm)

FuelCapacity............................... 1.6Quarts

OilCapacity....................... 22 Ounces(0.65liter)

NOTE:Forpractical operation, the engine load should not

exceed 85% of rated power. Enginepower will decrease

3-1/2% for each1,000 feet (300 meters) abovesea leveland

1% for each 10° F(5.6° C) above77° F(25° C). It should

operatesatisfactorily at an angle up to 15°.

OWHER'SRESPOHSIBILiTIES

Followthe hourly or calendarintervals, whichever occurs

first. More frequent service is required when operating in

adverseconditions noted below.

• Changeengineoil

• Check/clean water inlet screen1

• Checkhigh pressure hose

• Checkdetergentsiphoning hose

• Checkspray gun and assembly for leaks

• Cleandebris

• Checkengineoil level

• Service engineair cleaner2

• Changeengineoil2

• Service spark arrester

_ _ LLLLLL

Service spark plug

• Cleancooling system2

' Clean if clogged. Replaceif perforated or torn.

Service more often under dirty or dusty conditions.

General Recommendations

Regularmaintenancewill improve the performanceand

extend the life of the pressure washer. Seeany Searsor

other qualified service dealerfor service.

The pressure washer warranty does not cover items that

havebeensubjectedto operator abuse or negligence. To

receivefull valuefrom the warranty, the operator must

maintain pressure washer as instructed in this manual

including proper storage as detailedin Storage.

Someadjustments will needto be madeperiodically to

properly maintain your pressure washer.

All service and adjustments should be madeat least once

eachseason. Followthe requirements in the Maintenance

Schedulechart above.

NOTE:Oncea yearyou should clean or replacethe spark

plug and replacethe air filter. A newspark plug and cleanair

filter assure proper fuel-air mixture and help your engine run

better and last longer.

Pump Oil

DONOTattempt any oil maintenanceon this pump. The

pump is pro-lubricated and sealedfrom the factory, requiring

no additional maintenancefor the life of the pump.

EmissionsControl

Maintenance, replacement, or repair of the emissions

control devicesand systemsmay be performedby any non-

road engine repair establishmentor individual. However,

to obtain "no charge" emissions control service, the work

must be performed by a factory authorized dealer.Seethe

Emissions Warranty.

Before Each Use

1. Checkengine oil level.

2. Cleandebris.

3. Checkwater inlet screen for damage.

4. Checkhigh pressure hose for leaks.

5. Checkgun and nozzleextension assembly for leaks.

6. Purge pump of air and contaminants.

PRESSUREWASHERMAINTENANCE

Clean Debris

Daily or before use, cleanaccumulated debris from pressure

washer. Keeplinkage, spring and controls clean. Keeparea

around and behind muffler free from any combustible debris.

Inspect cooling air slots and openings on the pressure

washer.These openings must be kept cleanand

unobstructed.

Pressurewasher parts should be kept cleanto reducethe

risk of overheatingand ignition of accumulated debris.

• Usea damp cloth to wipe exterior surfaces clean.

• Usea soft bristle brush to loosen cakedon dirt, oil, etc.

• Usea vacuum cleanerto pick up loose dirt and debris.

[ NOTICE

Improper treatment of pressure washer candamageit and

_shorten ts fe.

__DO NOTinsertanyobjectsthroughcoolingslots.

Check and Clean Inlet Screen

Examinegarden hose inlet screen.Cleanif it is clogged or

replaceif it is torn.

Check High Pressure Hose

High pressure hoses can developleaks from wear, kinking,

or abuse. Inspect hose beforeeach use. Checkfor cuts,

leaks,abrasions, bulging of cover, or damageor movement

of couplings. If any of these conditions exist, replacehose

immediately.

WARHIHG

The high pressure stream of water that this

_ quipment produces cancut through skin and itsunderlyingtissues, leadingto serious injury and

)ossible amputation.

. NEVERrepairhighpressurehose.Replaceit.

• ReplacementhoseratingMUSTexceedmaximumpressure

ratingof unit.

Check Gun and Nozzle Extension

Examinehoseconnectionto spraygun and makesureit is

secure.Testtrigger bypressingit and makingsureit springs

backinto placewhenyou releaseit. Donotdepressred button

andtesttrigger.Youshouldnot beableto presstrigger. Replace

spraygun immediatelyif it failsanyofthesetests.

Hozzle Maintenance

A pulsing sensation felt while squeezingthe spray gun trigger

may be caused by excessivepump pressure.The principal

cause of excessivepump pressure is a nozzleclogged or

restricted with foreign materials,such as dirt, etc. To correct

the problem, immediately cleanthe nozzlefollowing these

instructions:

1. Shut off engine andturn off water supply.

2. ALWAYSpoint spray gun in a safe direction press red

button and and squeezespray gun trigger to release

retainedhigh water pressure.

WARHIHG

Thehigh pressure stream of water that this

equipment produces can cut through skin and its

_ nderlying tissues, leading to serious injury and

)ossible amputation.

Spraygun traps high water pressure, evenwhen

engine is stopped and water is disconnected,

which cancause injury.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

. ALWAYSpointspraygunin safedirectionpressred buttonand

squeezesprayguntrigger,to releasehighpressure,everytime

youstopengine.

3. Removenozzlefrom end of nozzleextension.

4. Usea small paperclip to free any foreign material

clogging or restricting nozzle (A).

Removenozzleextension from spray gun.

Using a garden hose, removeadditional debris by back

flushing water through nozzleextension. Backflush

between30 to 60 seconds.

7. Reinstallnozzleinto nozzleextension.

8. Reconnectnozzleextensionto spray gun.

9. Makesure garden hose is connectedto water inlet.

Checkthat high pressure hose is connectedto spray gun

and pump. Turn on water.

10. Start engine following instructions How to Start Your

Pressure Washer.

11. Test pressure washer by operating with eachquick

connect nozzle.

O-Ring Maintenance

Purchasean O-Ring RepairKitatyour localSearsor by calling

1-O80-4-MY-HONIE(469-4663} or onlineat www.sears.com.It

is notincludedwith thepressurewasher.This kit includes

replacemento-rings, rubberwasherandwaterinletfilter.Referto

theinstructionsheetprovidedinthekit to serviceyour unit's

o-rings.

WARHIHG

The high pressure stream of water that this

_ quipment produces cancut through skin and itsunderlyingtissues, leadingto serious injury and

)ossible amputation.

. NEVERrepairleakingconnectionswith sealantof anykind.

Replaceo-ringor seal.

ENGJHEMAINTENANCE

WARNING

_"_ Unintentionalsparking can result in fire or

_¢ electric shock.

WHENADJUSTINGORMAKINGREPAIRSTOYOUR

PRESSUREWASHER

. Disconnectthesparkplugwirefromthesparkplugandplace

thewirewhereit cannotcontactsparkplug.

WHENTESTINGFORENGINESPARK

• Useapprovedsparkplugtester.

. DONOTcheckfor sparkwith sparkplugremoved.

Oil

OilRecommendations

We recommendthe useof Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptableif classified for service SF,SG,

SH, SJ or higher. Do not usespecialadditives.

Outdoortemperatures determine the proper oil viscosity for

the engine. Usethe chart to selectthe best viscosity for the

outdoor temperature rangeexpected.

52 __ 0

.22 ..........................................................................

* Below40%(4°C)theuseofSAE30will resultin hardstarting.

** Above8O°F(27°0)theuseoflOW3Omaycauseincreasedoil

consumption.Checkoil levelmorefrequently.

_ OTE:Synthetic oil meeting iLSACGF-2,API

certification mark and APIservi,cesymbol with

"SJ/CF ENERGYCONSERVINGor higher, is an

acceptableoil atall temperatures. Use of synthetic oil

does not alter required oil changeintervals.

CheckingOilLevel

Oil levelshould be checkedprior to each useor at least every

8 hours of operation. Keepoil level maintained.

1. Makesure pressure washer is on a levelsurface.

2. Removeoil dipstick and wipe dipstick with cleancloth.

Replaceand tighten dipstick. Removeand and check oil

level.

3. Verify oil is at "Full" mark on dipstick. Replaceand

tighten dipstick.

AddingEngineOil

1. Makesure pressure washer is on a levelsurface.

2. Checkoil level as described in CheckingOil Level

3. If needed,slowly pour oil into oil fill openingto the

"Full" mark on dipstick. DONOToverfill.

4. Replaceand tighten dipstick.

ChangingEngineOil

Changeengine oil after the first 5 hours and every 50 hours

thereafter. If you are using your pressure washer under

extremely dirty or dusty conditions, or in extremely hot

weather, changeoil more often.

NOTICE

Overfilling with oil may causethe engineto not start, or

hard starting.

DONOToverfill.

Ifoverthe FULLmarkondipstick,drainoilto reduceoil levelto

FULLmarkondipstick.

CAUTION

Avoid prolonged or repeatedskin contact with usedmotor

oil.

Usedmotoroil hasbeenshownto causeskincancerin certain

laboratoryanimals.

Thoroughlywashexposedareaswith soapandwater.

KEEPOUTOFREACHOFCHILDREN.DON'T

POLLUTE.CONSERVERESOURCES.RETURN

USEDOILTOCOLLECTIONCENTERS.

Changeoil whiJeengineisstiffwarmfromrunning,asfoflows:

1. Drain fueltank by running pressure washer until fuel

tank is empty.

2. Disconnectspark plug wire and keepit away from spark

plug.

3. Cleanarea around oil fill, remove oil fill cap/dipstick.

Wipe dipstick clean.

4. Tipyour pressure washer to drain oil from oil fill into a

suitable container making sure you tip your unit away

from spark plug. When crankcaseis empty, return

pressure washer to upright position.

5. Slowly pour recommended oil (about 20 oz.) into oil fill

opening. Pauseto permit oil to settle. Fillto "Full" mark

on dipstick.

6. Wipe dipstick cleaneachtime oil levelis checked. DO

NOToverfill.

7. Replaceand tighten dipstick.

8. Wipe up any remaining oil.

9. Reconnectspark plug wire to spark plug.

Service Air Cleaner

Your enginewill not run properly and may be damagedif you

run it with a dirty air cleaner.

Servicethe air cleaneronce every 25 hours of operation or

once eachyear, whichever comes first. Service more often if

operating under dirty or dusty conditions. Replacementsare

availableatyour local Searsservicecenter.

Toservicetheair cleaner,followthesesteps:

1. Loosentwo screws (A) and lift off cover (B).

2. Carefully removeair cleaner (C)from base(B).

3. Install clean (or new) air cleanerin base.Air cleaner

must fit securelyin base.

4. Placecover over air cleanerand tighten screws.

NOTE:You canpurchase new air filter elements bycalling

1-SOO-4-NIY-NOIVIE(469-4663).

Service Spark Plug

Servicethe spark plug every 100 hours of operation or

yearly, whichever occurs first.

1. Cleanareaaround spark plug.

2. Removeand inspect spark plug.

3. Replacespark plug if electrodesare pitted, burned or

porcelainis cracked. Usethe recommended replacement

plug. See Specifications.

4. Checkelectrode gap with wire feelergauge and set spark

plug gap to 0.020 inch (0.50 mm) if necessary.

5. install spark plug and tighten firmly.

NOTE:You canpurchase a new spark plug bycalling

f-800-4-MY-NOME (469-4663).

Spark Arrester Service

Your engine is not factory-equipped with a spark arrester. In

some areas,it is illegal to operatean engine without a spark

arrester. Checklocal laws and regulations. A spark arrester is

availablefrom your nearest Searsservicecenter. If you need

to order a spark arrester, pleasecall f-OOO-4-MY-NOME

(469-4663).

Thespark arrester must be serviced every50 hours to keepit

functioning asdesigned.

If the engine hasbeen running, the muffler will be very hot.

Allow the muffler to cool before servicingthe spark arrester.

WARHJHG

_,_,_ Contactwith muffler resultin serious

area can

burns.

f_ Exhaustheat/gases can ignite combustibles,structures or damagefuel tank causing a fire.

DO NOTtouch hot parts and AVOIDhot exhaust gases.

Allow equipment to cool beforetouching.

Keepat least 5 feet (152 cm) of clearanceon all sides of

pressure washer including overhead.

Codeof FederalRegulation (CFR)Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engineto havea spark arrester, maintained in

effective working order, complying to USDAForestservice

standard 5100-1C or later revision. Inthe Stateof California a

spark arrester is required undersection 4442 of the California

Public resources code. Other statesmay have similar laws.

Page is loading ...

Craftsman 580.752200 Owner's manual

Brand: Craftsman

Model: 580.752200

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

580752200

Download PDF

report

in other languages

español: Craftsman 580.752200 El manual del propietario

Craftsman 580.752200 Owner's manual

This manual is also suitable for

Craftsman 580.752200 Owner's manual

in other languages

Related papers

Other documents