DKS 1812 Quick start guide

DKS
Brand
DKS
Model
1812
Type
Quick start guide
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
1
CENTRAL
OFFICE
EARTH
GND
PHONE
IN
PHONE
OUT
HOME
2345678
SW1
ENTRY BY-PASS
1875-010
1
CENTRAL
OFFICE
EARTH
GND
PHONE
IN
PHONE
OUT
HOME
2345678
SW1
ENTRY BY-PASS
1875-010
It is highly recommended that you consult the Installation/Owner’s manual for complete instructions on all the different types of installations. The 1812 Classic Telephone
Entry System involves the installation of the 1812 Classic cabinet, the by-pass board for the incoming telephone line, and wiring of these components (On reverse side). Be
sure that all dirt, metal or wood debris is removed from inside cabinet after mounting it. This could damage the control board and cause a malfunction during operation.
Remove Control Board from Cabinet
Flush Mount Cabinet in a Pilaster, Wall or Kiosk
The control board removal is the same for all models.
1. Unlock and open the 1812 Classic door.
2. Disconnect the keypad plug and door accessories
plug from the control board.
3. Remove the 4 screws. Carefully remove control board.
CAUTION Keep the control board in a protected area
during the installation.
Use existing 4 holes in cabinet box to bolt the surface or wall mount models on a DoorKing
mounting post (there are several different styles available). Use the hardware that is supplied with
the mounting post. Run all necessary wires through the post to the cabinet (See reverse side).
Mount Cabinet on a Mounting Post
Use the 4 existing holes in the cabinet box to screw the surface or wall mount models to
the wall. Run conduit inside or outside of wall or pilaster if desired. Use appropriate
hardware to mount the cabinet (Not supplied). Be sure that the mounting hardware does
not protrude into the cabinet where it could cause a short. Run all necessary wires through
the conduit to the cabinet (See reverse side).
Mount Cabinet Directly to a Wall or Pilaster
Install the By-Pass Board
The 1812 Classic by-pass board provides a method to by-pass the 1812 Classic and route the incoming
telephone line directly to the homeowner’s phone. It must be installed as part of the 1812 Classic
system. All telephone wires for the 1812 Classic must pass through the by-pass board.
Mount the by-pass board in a location that is easily accessible by the homeowner. In case of 1812 trouble
or maintenance, the homeowner will use the by-pass switch on the board to route the incoming telephone
line directly to their home phone. If the by-pass board is installed outdoors, it must be installed in a NEMA
Type 4 enclosure (not supplied) with conduit to protect the board and wires from direct exposure to
landscape sprinklers, rain, snow, and other elements.
NEMA Type 4
enclosure for
outdoor
installation.
(Not Supplied)
Use only twisted pair telephone wire that is rated for direct
underground burial (Cat5e Gel Filled (flooded) UV resistant
direct burial cable in conduit is recommended).
DO NOT use wire that is rated for indoor application use.
DO NOT run telephone wires in the same conduit as high
voltage AC wire.
It is recommended to run all necessary wires to the by-pass
board (See reverse side) in a “dedicated” telephone wire
conduit.
Ground by-pass board.
Minimum 12 AWG wire
(Not supplied).
If installed
outdoors.
Plastic screw anchors for
masonry if required.
(Not supplied)
Dedicated
Telephone
Wire Conduit
“Entry” switch position:
Routes incoming phone line through 1812 Classic
and then to the home phone.
“By-Pass” switch position:
Routes incoming phone line directly to the
home phone, bypassing 1812 Classic.
From
Incoming
Telephone
Line
From
1812
Classic
18-Pin
Main Terminal
Surface
Mount
Cabinet
Wall
Mount
Cabinet
Flush
Mount
Cabinet
7
8
9
4
5
6
1
2
3
0
7
8
9
4
5
6
1
2
3
0
7
8
9
4
5
6
1
2
3
0
Mount rough-in box into the pilaster, wall or kiosk. Run conduit inside wall into bottom of rough-in
box if desired. Use appropriate hardware (Not supplied) to secure the rough-in box in place. Run all
necessary wires through the conduit in to the rough-in box (See reverse side).
Bolt flush mount box
into the rough-in box
with 4 supplied bolts.
Rough-In Box
Flush
Mount
Box
7
8
9
4
5
6
0
Conduit
(Shown inside wall)
Conduit
(Shown inside wall)
IMPORTANT The 1812 Classic and
by-pass board MUST be properly
grounded! A gooseneck mounting
post anchored in concrete does not
make a good ground.
1
CENTRAL
OFFICE
EARTH
GND
PHONE
IN
PHONE
OUT
HOME
2 3 4 5 6 7 8
SW1
ENTRY BY-PASS
1875-010
2
3
4
5
6
7
8
1
From
Home
Phone
Incoming
Phone Line
Home Phone
Incoming
Phone Line
Home Phone
7 8 9
4 5 6
1 2 3
0
1
1
1
1
2
2
2
2
3
3
3
3
7 8 9
4 5 6
0
Remove the 18-pin main terminal
connector from the control board by
gently pulling it straight up. This will
make wiring to the control board
easier. Note the orientation and
numbering sequence of the
connector to correctly wire it.
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
QUICKSTART “BASIC” INSTALLATION GUIDELINES FOR AN 1812 CLASSIC CABINET AND BY-PASS BOARD
MIC
VOL
FB1
FB2
MASTER
CODE
ON
1871-010
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
EARTH
GND
SW1
ENTRY BY-PASS
1875-010
1
CENTRAL
OFFICE
PHONE
IN
PHONE
OUT
HOME
2345678
TIP
TIP
TIP
RING
RING
RING
TIP
RING
18
17
16
Com
15 N.C.
14 N.O.
13
Com
12 N.C.
11 N.O.
10
9
8
7
6
5
RING
4
TIP
3
GND
2 TIP
1 RING
24
VAC
It is highly recommended that you consult the Installation/Owner’
s manual for complete wiring instructions on all the different types of installations and programming.
By-Pass Board
Basic Programming for the 1812 Classic
Programming Momentary Access Codes
Control Board
The 1812 Classic has been programmed at the factory with many of the programming parameters (factory settings) set for a
typical residential application with a single 1812 Classic wired to an incoming phone line.
The 1812 is programmed from the factory with the last 4-digits of the control board serial
number as the “Master Code” which is used to program all advanced features.
If you are using more
than a single 1812 Classic in the system, or if you are using any of the advanced features of the 1812 Classic, such as Time
Zones, Do-Not-Disturb Schedules, Call Forward, Hold Open Schedules, Preprogrammed Phone Numbers, Access Codes, etc.,
you will need to download the complete Installation/Owner’s manual from our tech support web site.
The 1812 is programmed from the factory with the last 4-digits
of the control board serial number as the “Master Code”. It can
be reprogrammed if desired.
Programming Relay 1 and 2 Strike Time - (Factory setting is 1 second)
1. Press
*
0 3 and enter the MASTER CODE. [
*
0 3 _ _ _ _ (beep)]
2. Enter “1” for relay 1 or “2” for relay 2, then press
*
. [ _
*
(beep)]
3. Enter a two-digit strike time (00-99), then press
*
. [ _ _
*
(beep)]
Note: Strike time entered in seconds. 00 = ¼ sec., 06 = 6 seconds, etc.
4. Repeat steps 2 and 3 to set the other relay strike time if necessary.
5. Press “0 #” TOGETHER to end. [0 # (beeeeeep)]
This “Quickstart” guideline is designed for installing a single 1812
Classic in a typical single family home application using the factory
settings already programmed in the 1812 Classic. Complete
installation instructions manual is available on the enclosed CD AND
from our tech support web site.
CLICK HERE TO VISIT DOORKING’S TECHNICAL WEB SITE:
www.dkaccess.com/english/Telephone_Entry/telephone_entry.html.
1. Turn Master Code switch ON.
2. Enter a four digit Master Code number
then press “
*
”, “beep” will be heard.
[ _ _ _ _ (beep)] (Write down your master code).
3. Turn Master Code switch OFF.
Switch OFF - Normal operating mode positon (position shown).
Switch ON - After master code switch has been turned ON, system
will be in Master Code programming mode. (If master code switch
is turned ON and master code is not entered, the system will
sound a short tone after 30 seconds and continue every 30
seconds until master code is entered or switch is turned off).
Master Code Switch Description
“Normally Open”
Vehicular
Gate Operator
(Terminal 11 and 13)
INPUT
PHONE LINE
TIP RING
1877-010
OUTPUT
TIP RING GNDGND
LOW VOLTAGE LINE
OUTOUT
1878-010
ININGNDGND
INPUT
OUTPUT
Locate Homeowner’s
Phone Line Inside Device
To “Existing”
Alarm Control Panel
“Existing” Alarm System
Phone
Jack
Phone
Jack
Cat5e Cat5e
Cat5e Without Surge Board
Without
Surge
Board
Central Office (C.O.)
Demarcation Device
Cat5e
Cat5e
Recommended
Recommended
Recommended
Cat5e
Ground 12 AWG Min.
Ground 12 AWG Min.
Within 3 ft of Board
Ground 12 AWG Min.
Within 3 ft of Board
Ground 12 AWG Min.
Phone at
Home #12
Phone at
Home #11
Phone at
Home #13
Tip
Ring
Tip
Ring
Tip
Ring
Homeowner’s Phone(s)
“Normally Close” Pedestrian Gate/Door with Maglock
(Terminal 15 and 16)
“Normally Open” Pedestrian Gate/Door with Electric Strike
(Terminal 14 and 16)
Maglock
Electric
Strike
WARNING
MO
V
IN
G
G
A
TE C
AN
C
A
U
S
E
Op
er
at
e
ga
t
e
on
l
y
w
h
en
gat
e
ar
ea
i
s
i
n
si
gh
t
and
f
r
e
e
of
peopl
e
and
obst
r
uct
i
ons.
Do
not
a
l
l
ow
chi
l
d
r
en
t
o
pl
ay
i
n
g
at
e
ar
ea
or
oper
at
e
gat
e.
Do
not
s
t
and
i
n
gat
e
pat
h
or
wal
k
t
hr
ough
pat
h
whi
l
e
gat
e
i
s
m
ovi
n
g.
Read
owner
’
s
m
anu
a
l
a
nd
saf
e
t
y
i
n
st
r
uct
i
ons.
SE
RIOUS INJURY OR DE
AT
H
C
LA
S
S
C
ER
TI
FIED TO
C
A
N/
C
S
A
C
22.2
NO
. 2
47
C
ONFORMS
TO
A
NS
I/UL-325
V
EHIC
ULA
R GA
TE OP
E
RATOR
HP
5
33
8
2
MOD
E
L
S
ERIA
L
V
OLTS
P
HA
S
E
A
MP
S
60
Hz
MA
X
GA
T
E LOA
D
D
o
o
r
K
in
g
,
In
c.
,
I
n
g
le
w
o
o
d
,
C
A
TIP (
+
):
White/blue mark
RING (-):
Blue/white mark
Magnetic locks or electric strikes must be powered from a
separate UL Listed power transformer. DO NOT power electric
strikes or magnetic locks from the 1812 Classic power
transformer. keep power wire runs as short as possible.
Adjust feedback from phone lines if necessary.
Refer to Installation/Owner’s manual for more
information.
Use common electrical safety practices when connecting
telephone wires. You can receive a substantial jolt if the
phone rings while handling these wires.“RING” terminal
voltage varies and can be between -48 to -130 Volts AC,
depending on the distance to the central office.“TIP”
terminal is always positive with respect to RING terminal.
The By-Pass board is required.
Phone Line Surge Suppressor
Optional P/N 1877-010
Low Voltage
Surge Suppressor
Optional P/N 1878-010
Separate UL
Listed Power
Transformer
Check Polarity of Telephone Line
Check for polarity on the incoming telephone line to each board and maintain polarity
throughout the telephone line (TIP (+), RING (-).
Cat5e Gel Filled (flooded) UV resistant direct burial cable run in conduit recommended.
DO NOT run telephone wires in the same conduit as high voltage AC wire.
Main
Terminal
TIP
Older Lines
Green Wire (+)
Older Lines
Red Wire (-)
RING
Ground
Ground
Ground
Ground
Phone In
(1-2)
MAS
MAS
CO
Relay 1
(11-13)
SPEAKER
VOL
MIC VOL
Do Not Adjust
Resident Phone Line Feedback
Outside Phone Line Feedback
Wire Size Max Distance
24 AWG
22 AWG
20 AWG
18 AWG
800 ft
1600 ft
2200 ft
3600 ft
Telephone Wire Run (Cat5e) Table
Wire Size Max Distance
18 AWG
16 AWG
100 ft
200 ft
24 VAC Power Transformer and
Access Control Device(s)
Wire Run Table
Supplied 24 VAC Power
Transformer
Polarity does not matter.
Programming the “Master Code”
ReProgram MASTER CODE
Access Control Devices
RJ31x
Phone Jack
installed
Before 1812
System
Telephone Company
Demarcation Point
Complete Instructions
Programming Momentary Access Code(s) to Operate Relay 1 and/or 2 on a 24/7 Basis - (Maximum of 14 codes per relay)
1. Press
*
0 2 and enter the MASTER CODE. [
*
0 2 _ _ _ _ (beep)]
2. Enter a two-digit “location code” to determine which relay will be activated, (01-14) - relay 1’s location OR (26-39) - relay 2’s location, then press
*
. [ _ _
*
(beep)]
3. Choose and enter a four-digit momentary access code, then press
*
. [ _ _ _ _
*
(beep)]
4. Repeat steps 2 and 3 to enter additional momentary access codes for each relay, do not duplicate or go beyond “location code” number limits for each relay.
5. Press “0 #” TOGETHER to end programming. [0 # (beeeeeep)] (Write down all your access codes on log sheets in back of Installation/Owner’s manual).
Cat5 Wire
Four Conductor
Wire
Tip (+)
1st Line
Wire
Conversion
2nd Line
3rd Line
4th Line
Green
Red
Black
Yellow
Blue Pair
Orange Pair
Green Pair
Brown Pair
Ring (-)
(+) Tip
(-) Ring
(+) Tip
(-) Ring
(+) Tip
(-) Ring
Older
Residential
Homes
Modern
Residential
Homes
Phone Wiring
Basics “101”
Relay 2
(14-16)
Power
(17-18)
Phone Out
(4-5)
IMPORTANT All boards
MUST be properly
grounded or the system
will NOT function correctly!
Orange Pair
Orange
Pair
Green
Pair
Green Pair
Note: Each relay can control a
normally open OR normally close
access control device. Relay
contacts are rated for 3 amps @
30 VAC maximum.
Output
24 VAC
20 VA
ON
OFF
QUICKSTART “BASIC” WIRING GUIDELINES FOR AN 1812 CLASSIC SYSTEM WITH TWO ACCESS CONTROL DEVICES
Copyright 2012 DoorKing, Inc. All rights reserved.
1812-163-K-8-12
  • Page 1 1
  • Page 2 2

DKS 1812 Quick start guide

DKS
Brand
DKS
Model
1812
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents