Etac Turner Pro Operating instructions

Etac
Brand
Etac
Model
Turner Pro
Type
Operating instructions

Etac Turner Pro is a versatile and easy-to-use assistive device that helps users safely stand up from a sitting position. It features a rotating mechanism that enables smooth and controlled turns, making it ideal for users who have difficulty with balance or mobility. The Turner Pro also has a height-adjustable handle and a comfortable seat that can be positioned at different angles to accommodate various user needs. Additionally, it comes with a range of accessories, such as a back support and a tray, to enhance its functionality and comfort.

Etac Turner Pro is a versatile and easy-to-use assistive device that helps users safely stand up from a sitting position. It features a rotating mechanism that enables smooth and controlled turns, making it ideal for users who have difficulty with balance or mobility. The Turner Pro also has a height-adjustable handle and a comfortable seat that can be positioned at different angles to accommodate various user needs. Additionally, it comes with a range of accessories, such as a back support and a tray, to enhance its functionality and comfort.

Turner PRO
EN
Reconditioning
2.
SV
Rekonditionering
4.
NO
Rekondisjonering
6.
DA
Fornyelse
8.
FI
Kunnostus
10.
DE
Instandsetzung
12.
NL
Revisie
14.
FR
Reconditionnement
16.
IT
Reconditioning
18.
ES
Ajustes
20.
RE61099 rev C 2019-15-10
Reconditioning
Turner PRO
2
Wheels / Wheel axles
3
Rotating mechanism
2
If turner rotates porly:
• Unscrew bolt (5).
• Clean Low friction disc (2) and floor plate (1).
• If deep groves or damages in (1) or (2), replace
(1,2,3,4,5).
• Apply loctite 243 or simular on bolt (5), tighten bolt
firmly (approx 20Nm).
If antislip knobs are missing:
• Clean holes.
• Apply Loctite 460 and push in new knobs.
Washing
1
• Lay the Turner PRO on the floor in an angeled position
after washing, so the water runs out of the rotating
mechanism.
• You may also use copressed air to blow dry inside
rotating mechanism.
• Controls wheel and shaft for wear.
• Check if the wheels turn easily, remove hair and dirt.
If wheels are worn out, or still rotates porly after
cleaning:
3
1
5
4
2
• Use a solvent-free detergent with a pH level bet-
ween 5 and 9.
• Can be washed at 70° C for 10 minutes.
3
1
2
• Flip out starlock with
an screwdriver or
simular (1).
• Remove bolt and
wheel.
• Replace 1,2,3.
• Place wheel between
forks.
• Insert bolt and knock
.starlock in place.
EN
Reconditioning
Turner PRO
3
Leg Support
4
Main plate/outer pole
5
• Check bracket on leg support for cracks and
wear. If cracs, replace coplete leg support.
• Check cushion for wear, should be tight and firm
around the pipe. If loose or damaged, replace
coplete leg support.
Original spare parts from Etac should always be used.
Handle/inner pole
6
• Check for cracs and dents, if cracs or dents
replace inner pole.
If complete leg support needs to be replaced:
• Unscrew bolts and remove outer pole.
• Pull leg support out of pole.
• Insert leg support with kneepads pointing upwards
• Make sure both knobs are on the same side (1).
• Tighten knob by turning knob clockwise (2).
• Place the base plate on an even surface. Insert
pole with knee pads facing away from
the wheels.(1)
• Insert all three screws into holes in the base
plate. Use allen key to screw in bolts. Apply
loctite 243 or simular on bolts, tighten
bolt firmly, (approx 20Nm). (2)
1
2
1
2
• Check for cracks and wear on main plate and
outer pole. If cracks, replace complete Turner-
PRO.
• Check bolted conection between pole and
main plate (3 bolts), if loose bolts tighten all
bolts.
EN
Reconditioning
Reconditioning
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Etac AS
Etac Supply Gjøvik
Hadelandsveien 2, 2816 Gjøvik, Norway
Tel +47 4000 1004
molift@etac.com www.etac.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Etac Turner Pro Operating instructions

Etac
Brand
Etac
Model
Turner Pro
Type
Operating instructions

Etac Turner Pro is a versatile and easy-to-use assistive device that helps users safely stand up from a sitting position. It features a rotating mechanism that enables smooth and controlled turns, making it ideal for users who have difficulty with balance or mobility. The Turner Pro also has a height-adjustable handle and a comfortable seat that can be positioned at different angles to accommodate various user needs. Additionally, it comes with a range of accessories, such as a back support and a tray, to enhance its functionality and comfort.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents