Rexel RSM1130 User manual

Category
Paper shredders
Type
User manual

This manual is also suitable for

English 4
Français 8
Deutsch 12
Italiano 16
Nederlands 20
Español 24
Português 28
Türkçe 32
Ελληνικά 36
Dansk 40
Suomi 44
Norsk 48
Svenska 52
Polski 56
Česky 60
Magyar 64
Pyccкий 68
Mercury
Specifications
RSS2030
20 sheets
(19 sheets @ 207V/50Hz)
4 mins on / 20 mins off
230V AC / 50Hz
1.5A
RSX1630
16 sheets
(15 sheets @ 207V/50Hz)
4 mins on / 20 mins off
230V AC / 50Hz
1.9A
RSM1130
11 sheets
10 sheets @ 207V/50Hz)
4 mins on / 20 mins off
230V AC / 50Hz
2.2A
RSX1632
16 sheets
(15 sheets @ 207V/50Hz)
4 min on / 30 min off
230V AC / 50Hz
2.9A
RSS2232
22 sheets
(21 sheets @ 207V/50Hz)
4 min on / 30 min off
230V AC / 50Hz
1.9A
RDS2250
22 sheets
(21 sheets @ 207V/50Hz)
Continuous
230V AC / 50Hz
1.2A
Models
Sheet Capacity
80gsm paper -
Duty Cycle -
Volts / Hz
Amperage
IMPORTANT: ONLY INSERT ONE CD OR ONE CREDIT CARD AT A TIME.
Models RDM1150, RDM1170, RDSM750, RDSM770 and RSM1130 cannot shred CDs, credit cards, paper clips or staples.
m
RDX1850
18 sheets
(17 sheets @ 207V/50Hz)
Continuous
230V AC / 50Hz
2.0A
Models
Sheet Capacity
80gsm paper -
Duty Cycle -
Volts / Hz
Amperage
RDM1150
11 sheets
(10 sheets @ 207V/50Hz)
Continuous
230V AC / 50Hz
3.5A
RDM1170
11 sheets
(10 sheets @ 207V/50Hz)
Continuous
230V AC / 50Hz
3.5A
RDSM770
7 sheets
(6 sheets @ 207V/50Hz)
Continuous
230V AC / 50Hz
3.5A
RDSM750
7 sheets
(6 sheets @ 207V/50Hz)
Continuous
230V AC / 50Hz
3.5A
RDS2270
22 sheets
(21 sheets @ 207V/50Hz)
Continuous
230V AC / 50Hz
1.2A
RDX2070
20 sheets
(19 sheets @ 207V/50Hz)
Continuous
230V AC / 50Hz
2.0A
4
Introduction
Thank you for choosing this shredder from Rexel. We are sure it will serve you well, but please take a little time to study these
instructions to ensure you get the best out of your machine.
a Important Safety Symbols
b RSX1632, RSS2232, RSS2030, RSX1630, RSM1130:
Pull Out Bin
RDS2250, RDX1850, RDS2270, RDX2070, RDM1150,
RDM1170, RDSM750, RDSM770: Door for Bin
c Wheels
d On/Off Button (Rear of machine)
e Auto Button
f Reverse Button
g Continuous Forward Function
h CD Guide (not fitted on RDM1150, RDM1170, RDSM750,
RDSM770, RSM1130)
i Oil Level
j Oiling in Operation
1 Bin Full (Red Light)
2 Door Open (Red Light)
3 Cool Down (Red Light)
4 Auto Oiling in Operation
5 Oil Level Indicator
Safety First
Shredders are safe to use as long as you take a few safety
precautions.
Ensure the machine is plugged into an easily accessible
power outlet, and ensure the cable is not likely to trip up a
passer by.
Any attempt to repair this unit by unqualified personnel will
invalidate the warranty. Please return to supplier.
Unplug your shredder before moving it or when it is not in
use for an extended period of time.
Do not operate with a damaged power supply cord or plug,
after it malfunctions, or after it has been damaged in any
manner.
Do not overload electrical outlets beyond capacity as this can
result in fire or electrical shock.
The socket-outlet should be installed near the equipment and
shall be easily accessible.
Do not alter the attachment plug. The plug is configured for
the appropriate electrical supply.
Do not use near water.
Do not use aerosol dusters or cleaners.
Do NOT spray anything into the shredder.
Although this shredder has been designed to be child safe, it is
not advised to operate the machine near children and pets.
m
Lights and Icons Explained
LEDs
1 2 3 4 5
Anti-Jam Indicator Auto Bin Full Door Open Cool Down* Oil Level Oiling/Auto
Colour of LED Red Green Blue Red Red Red Red Green
Power On/Off Switch
Auto Mode light light
Forward Mode light light
Reverse Mode light light
Mercury Anti-Jam Technology light light
Bin Full light light light
Door/Bin Open light light light
Cool Down Indicator light* light*
Self Cleaning of Cutters light light
Sleep Mode
Auto Oiling in Operation light light
Oil Level Indicator light light
* RSS2030, RSX1630, RSM1130, RSS2232, RSX1632 only
5
G
Mercury Anti-Jam Technology
Mercury Shredders will only shred stacks of paper that are
within the shredder’s sheet capacity. For example, a shredder
with a capacity of 22 sheets will not allow the shredding of
more sheets than this.
Sensors in the paper feed area measure the thickness of
paper about to be shredded. The ability to shred or not is
communicated through red and green lighting. Green means
that the stack of paper is within the shredders sheet capacity
and OK to shred. Red means that you have too much paper,
remove some sheets in order to shred.
Given that you are unable to shred more sheets of paper
than the shredder is capable of shredding, paper jams are
prevented.
This prevents time wasted through reversing paper and
unblocking jams not to mention the mess it can create.
Rare Occasions of Jamming
In the unlikely event of the shredder jamming, use the reverse
function to unblock the shredder (see Reverse function section).
Alternating between the reverse and continuous forward
functions will help unblock the feed area.
Door Open Safety Function
If the door is opened during shredding as a safety precaution
the shredder will instantly stop, and the door open symbol/
indicator will glow red.
Over Heating
If small office models (RSS2030, RSX1630, RSM1130,
RSS2232 and RSX1632) are used continuously for long
periods of time the shredder may overheat. If this occurs the
thermometer symbol on the indicator panel will illuminate.
When the shredder is ready to be used again the thermometer
symbol will not illuminate.
RSM1130, RDM1150 and RDSM750 only.
This means do not shred CDs.
This means do not shred credit cards.
This means do not shred staples.
This means do not shred paper clips.
Shredder Control Panel
ReverseForwardAuto
Safety First
This means you should be careful because long hair can become
entangled in the cutting head.
This means don’t reach into the feed opening of the cutting
head.
This means be careful of ties and other loose clothing which
could become entangled in the cutting head.
This means keep children away from shredder.
This means be careful of loose jewelry which could become
entangeld in the cutting head.
This means the door is open.
This means the bin is full.
This means no aerosols.
This means machine is cooling down.
This means oil level.
This means oiling in operation.
Initial Setup
The shredder is designed to automatically lubricate the cutting
mechanism as required to ensure the product continues to
work to its maximum performance and to extend the product
life. Before turning on the machine for the first time, please
open the oil reservoir cap on the head of the shredder (j) and
pour in the 60ml bottle of oil provided as standard. This is
sufficient to allow the shredder to start for the first time and
to operate continuously for approximately 1 hour shredding
before the reservoir will need refilling. Press and hold down the
Auto button (f) for 5 seconds to start the pump and prime the
system. This operation is only required the very first time the
shredder is used. When the ‘Oil Refill’ indicator is illuminated
, flip up the oil reservoir cap (j) and refill the oil reservoir
using a bottle of standard Rexel oil (1760049). The automatic
oiling operation lasts approximately 2 seconds and you
will hear the distribution pump during this time. Auto-oiling
operates after 15 minutes of shredding.
6
Reverse Function
1 Should you wish to reverse the shredding direction whilst
shredding a document, a reverse button (f) has been fitted
for your convenience.
2 By pressing the reverse button the shredding cutters will
change direction allowing the retrieval of the document
being shredded. The anti-jam indicator will turn to red.
3 The reverse function will only run whilst the button is being
pressed. When the reverse button has been released the
shredder will revert to stand by mode.
4 To turn back to auto mode, press the auto button (e).
CD and Credit Card Shredding
Models RSM1130, RDM1150, RDM1170, RDSM750 and
RDSM770 can not shred CD’s or credit cards, therefore this
section is not applicable to these three models. All other
Mercury models can shred CD’s and credit cards as follows:
1 A separate CD tray is provided to collect the shredded CD
shards. Ensure that this is correctly mounted onto the bin
rail or internal bin (small office models) before shredding
CDs or credit cards. CD and credit card shards should be
disposed of separately to paper.
2 Pull up the CD guide (h) located in the centre of the feed
area and flip it into position over the shredder mouth.
3 For credit card shredding, switch the shredder to auto mode
and insert the card in line with the arrow marked on the
shredder mouth. Only shred 1 credit card at a time.
4 For CD shredding, extend the sides of the CD guide, switch
the shredder to auto mode and place the CD into the centre
of the CD slot. Only shred 1 CD at a time.
5 Empty the CD tray after 8 credit cards or CD’s to avoid
waste spilling over into the paper waste bin. Remove the CD
tray before recommencing to shred paper.
Operation
1 After unpacking the product, pull out the shredder bin or
bag frame (depending on model) and remove the CD shard
tray, which sits on top of the bag frame on departmental
models or bin on small office models. Store this tray on the
external location points (i) and use when you shred CD’s or
credit cards to separate waste for recycling (not applicable
for RSM1130, RDM1150, RDM1170, RDSM750 and
RDSM770 models).
2 Connect shredder to mains supply.
3 Ensure the on/off button on the back of the machine is in
the on position (d).
4 To commence shredding, press the central Auto button (e).
This will illuminate the anti jam indicator.
This sets the shredder into auto mode and initiates the
Mercury anti jam mechanism. The standby symbol will
illuminate blue and the anti-jam indicator will glow green.
You are now able to shred.
5 Insert paper to be shredded into the feed area. The Mercury
anti jam mechanism will sense the thickness of the paper
being shredded.
If the paper thickness is within the shredder’s capacity,
the motor will start and your documents will be shredded.
Cutters will stop once the shredding process is complete.
If the paper thickness is greater than the shredder’s sheet
capacity, the anti-jam indicator will turn from green to red
and the motor will not run.
6 If this happens, remove some of the sheets from the paper
stack and re-try until the anti-jam indicator reverts back to
green, the shredder will then automatically start and allow
the paper to be shredded.
7 If the shredder is left in auto mode for more than 2 minutes
without being used, the shredder will automatically turn
back to standby mode in order to save power.
8 The shredder will automatically ‘wake up’ from sleep mode
when paper is inserted into the shredder mouth. There is no
need to press the Auto button (e).
7
G
Guarantee
ACCO Brands warrants its products and their parts against
defects in materials and workmanship under normal use for a
period of 24 months from the original date of purchase.
During this period we will repair or replace a defective product
or part subject to the following warranty conditions:
The warranty applies only to defects in materials and
workmanship under normal use and does not extend to
damage to the Product or parts which result from:-
alteration, repair, modification or service carried out by
anyone other than an authorised ACCO service centre.
accident, neglect, abuse or misuse owing to failure to
comply with the normal operating procedures for a product
of this type.
Nothing in this Warranty shall have the effect of excluding the
liability of ACCO in respect of death and personal injury caused
by the negligence of ACCO. This Warranty is offered (subject to
these terms and conditions) in addition to, and does not affect
your statutory rights.
Additional Guarantee
ACCO Brands guarantees the cutting blades of the shredder
to be free from defects in material and workmanship for
10 years on the RSS2030, RSX1630, RSM1130, RSS2232
and RSX1632 and for 20 years on the RDS2250, RDX1850,
RDM1150, RDM1170, RDSM750, RDSM770, RSS2270 and
RDX2070 from the date of purchase by the original consumer.
* Please note that the cutter blades will be progressively worn
down by shredding fastened sheets (staples and paperclips)
- this is not covered in the warranty. With regards to CD
shredding, Rexel departmental and small office shredders have
been designed to shred up to 500 and 300 CDs respectively
during the warranty period. Excessive cd shredding will wear
the cutters and is not covered within the warranty.
**Models RSM1130, RDM1150, RDM1170, RDSM750 and
RDSM770 have NOT been designed to shred CD’s, credit
cards, paper clips or staples. Any attempt to do so will
invalidate this warranty.
These conditions shall in all respects be governed and
construed in accordance with English Law and subject to the
exclusive jurisdiction of the English Courts.
Bin Full
When the bin is full the shredder will not function and the bin
full symbol will illuminate red.
When this happens you must empty the bin.
Pull open the bin to empty (RSS2030, RSX1630, RSM1130,
RSS2232, RSX1632)
Open the door and pull out the bag frame (RD2250,
RDX1850, RDM1150, RDM1170, RDSM750, RDSM770,
RDS2270, RDX2070)
Once the bin is empty, close the door/drawer and press the
auto button to resume shredding.
Note: RSX1630, RSX1632, RDX1850, RDX2070, RDM1150,
RDM1170, RDSM750, RDSM770 - Once the waste bag has
been reinserted and/or cabinet door has been closed, the
shredder will run in reverse for three seconds, stop for two
seconds and then forward for three seconds to clear away any
remaining paper from the cutter mechanism. This unique ‘self-
cleaning’ mechanism is additional jam prevention technology
from Rexel.
Shredder Accessories
We recommend that a paper waste sack for recycling shredded
paper is used on all models. Please see the table below for the
correct accessory code for your model.
Model Accessory Part Box
Description Number Qty
RSS2030 Recycling Waste Sack 2102063 20
RSX1630 Oil Sheets 2101949 20
RSM1130
RSS2232 Recycling Waste Sack 2102505 50
RSX1632 Oil Sheets 2101949 20
RDS2250 Recycling Waste Sack 2102441 50
RDX1850* AS1000 Plastic Waste Sack 40070 100
RDM1150*
Oil Sheets 2101949 20
RDSM750*
*Rexel Shredder Oil 1760049
RDS2270 Recycling Waste Sack 2102442 50
RDX2070* AS1000 Plastic Waste Sack 40070 100
RDM1170*
Oil Sheets 2101949 20
RDSM770*
*Rexel Shredder Oil 1760049
ACCO Brands Europe
Oxford House
Aylesbury HP21 8SZ
United Kingdom
www.accoeurope.com
Ref: CBT.6535
Issue: 2 (07/10)
G ACCO Service Division
Hereward Rise, Halesowen, West Midlands, B62 8AN
Tel: 0845 658 6000, Fax: 0870 421 5576
www.acco.co.uk/service
F ACCO France
Service Aprés-Vente
Tel: 0820 872 356, Fax: 03 80 68 60 49
D ACCO Deutschland
Arnoldstrasse 5, 73614 Schorndorf, Germany
Tel: +49 7181/887-420, Fax: +49 7181/887-498
E ACCO Iberia SL
P Isaac Peral 19, 28820 Coslada (Madrid)
Tel: 91 669 9391, Fax: 91 672 07 11
I ACCO Brands Italia Srl
Via Pietro Nenni 13, Settimo Torinese (TO)
Tel: +39 011 896 11 11, Fax: +39 011 896 11 13
B ACCO Brands Benelux B.V.
Peppelkade 64, 3992AK Houten, Nederland/Les Pays-Bas
Tel: 0800-73362, Fax: 02-4140784
[email protected], www.accobenelux.be
o ACCO Brands Benelux B.V.
Peppelkade 64, 3992AK Houten, Nederland/Les Pays-Bas
Tel: 0800-21132, Fax: 02-4140784
[email protected], www.accobenelux.be
O ACCO Brands Benelux B.V.
Peppelkade 64, 3992AK Houten, Nederland/Les Pays-Bas
Tel: 030-6346060, Fax: 030-6346070
[email protected], www.accobenelux.nl
S ACCO Brands Nordic AB
c Makadamgatan 5, 254 64 Helsingborg, Sweden
N Tel: +46 42 38 36 00, Fax: +46 42 38 36 10
o
o
o
o
XERTEC a.s.
o U Továren, 770/1b, 102 00, Praha 10, Ceska Republika
Tel: +420 271 741 800, Fax: +420 271 743 143
www.xertec.cz
Q SERWIS ACCO
05-300 Mińsk Mazowiecki, Ul. Grobelnego 4, Polska
Tel: +48 25 758 11 90, Fax: +48 25 758 11 90
H ACCO Hungária Kft
Budapest, Ócsai út 4., 1239, Hungária
Tel: +36 1 283 1645, Fax: +36 0 283 0928
o
Представительствокомпании
«АККОДойчландГМБХиКО.КГ»
Россия 105005, Москва, Денисовский пер., д.26
Тел: (495) 933-51-63, Факс: (495) 933-51-64
o
ПолиграфическиеСИСТЕМБ
03110 Киев, Украина, Пр.Червонозоряний, 51,
офис 216 лабораторного корпуса НИИ СП
Тел: (+38) 044 495-1293, Факс: (+38) 044 248-4923
o ACCO Australia Pty Ltd
Level 2, 8 Lord Street, Botany, NSW, Australia 2019
Tel: +61 2 9700 0180, Fax: +61 2 9700 0195
A ACCO Österreich
Sallmann Bürotechnik GmbH, Schumacherstr.13, 5020 Salzburg
Tel: 0662 4345 160, Fax: 0662 4345 164
C ACCO Schweiz
ABC Bürotechnik AG, Winkelbüel 4, 6043 Adligenswil
Tel: 041 375 6060, Fax: 041 375 6061
o ACCO-Rexel Ltd
Clonshaugh Business & Technology Park, Clonshaugh, Dublin 17, Ireland
Tel: 01 816 4300, Fax: 01 816 4302
[email protected], www.accorexel.ie
o GBC Asia Pte Ltd
o 47 Ayer Rajah Crescent, #05-08/17, Singapore 139947
o Tel: +65 6776 0195, Fax: +65 6779 1041
o GBC-Japan K.K.
14F Harmony Tower, 1-32-2 Honcho, Nakano-ku, Tokyo 164-8721
Tel: (81)-03-5351-1801, Fax: (81)-03-5351-1831
[email protected], www.gbc-japan.co.jp
IRL
RUS
AUS
Service
LUX
CZ
LV
EST
LT
SK
UR
JPN
IND
PAK
BD
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74

Rexel RSM1130 User manual

Category
Paper shredders
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI