Cooper Lighting CT Circuit T Installation guide

Risk of Fire and Electrical Shock- MWS must

be installed by qualified personnel. If not

qualified, consult an electrician.

Risk of Electric Shock- Disconnect power at

fuse or circuit breaker before installing or

servicing.

Ensure both latches are securely fastened-

Unlatched connections can separate causing

arcing and overheating of the connectors.

WARNING

IMPORTANT: Read, understand and follow all MWS

safety and installation instructions. Retain for future

reference.

NOTICE: Installation must comply with all applicable

national and local codes. Manufactured wiring systems

covered by Article 604 of the National Electrical Code.

NOTICE: Do not use any MWS component for other

than it’s intended purpose.

NOTICE: Do not tamper with the internal wiring of any

MWS component or physically modify in any way.

NOTICE: Starter fitting/starter fixture cable is

the starting point of the MWS system. All MWS

components attached to the system will be energized.

Cap all unused connector openings.

Installation Instructions – MWS 0-10V Dimming

Instructions d’installation–Système de câblage modulaire de

gradation0 à 10V

Instrucciones de instalación – Atenuación MWS 0-10V

IMPORTANT: Save installation instructions for future changes.

IB519111EN

MWS

Failure to comply with these instructions may result in

death, serious bodily injury and property damage.

DISCLAIMER OF LIABILITY: Eaton assumes no liability

for damages or losses of any kind that may arise

from the improper, careless, or negligent installation,

handling or use of this product.

INSTALLATION

1. Standard carton size 14”W x 14”L x 12”H

Half carton size 14”W x 14”L x 6”H.

2. Each carton label list component cat. no. quantity,

length voltage with photograph.

3. Standard pallet size: 32”W x 46”L x 42”H

Max. 18 cartons per pallet. Pallets are shrink

wrapped by Cooper.

120V/277V/347V

Grey

Purple

Black

White/Neutral

Green

0-10V Dimming

5

4

3

2

1

5

4

3

2

1

MWS Standard Contact Configuration

CAUTION

Only use with compatible MWS 0-10V

components.

0-10V Dimming

12/2G

10/2G

2

Consult MWS Installation, Application and Specification Manual for

additional comprehensive system information.

Starter Fitting/Starter Cable

MWS IB519111EN Installation instructions

Installation Instructions – MWS 0-10V Dimming

System View (not to scale)

Dimensional and Mounting Details

Starter (ST)

Converts conventional wiring to MWS. Branch circuits are fed from the panel to a junction box with conduit and wire. The Starter is

mounted to the junction box with a 1/2” threaded lock nut connector. Circuits are then connected to the appropriate leads of the Starter.

Starter Cables have 9’, 15’ or 21’ of MC cable.

Fixture Cable

System View (not to scale)Dimensional and Mounting Details

Fixture Cable (FC)

Feeds power to fixtures and allows circuits to be carried through to other fixtures. Locks into 1/2” KO of access plate, fixture body or

J-box. The unit adds 7/8” to overall height of the fixture.

Typical MWS Wiring System Application shown utilizing Fixture Cable (FC).

Extender Cables

System View (not to scale)Dimensional and Mounting Details

Extender Cable (EC)

Supplies power between MWS components. Cables connect together without use of couplers.

Typical MWS Wiring System Application shown utilizing Extender Cable (EC).

STARTER FITTING STARTER CABLE

Unit with no cable

Starter

Starter Cable

Fixture Cable

Extender or Fixture Cable

Front

3/4”

[19mm]

3/4”

[19mm]

4-3/8”

[112mm]

1-7/8”

[47mm]

4-3/8”[112mm] 4-3/8”[112mm]

3/4”

[19mm]

5/8”

[16mm]

4-3/8”

[112mm]

5/8”

[16mm]

1-7/8”

[47mm]

4-3/8”

[112mm]

3/4”

[19mm]

4-3/8”

[112mm]

Front

To p

Front

Fixture Cable Fixture Cable Fixture Cable

Quick Connect

Front

Front Front

Starter

Circuit T

Extender Cable

Switch Drop

Fixture Cable

Fixture

Cable

Fixture

Cable

Fixture Cable

Extender

Cable

Extender Cable

Drop SO Cord

Switch

Drop

To p

Side

To p

Side

To p

Side Side

3

MWS IB519111EN Installation instructions

Installation Instructions – MWS 0-10V Dimming

Circuit T

System View (not to scale)Dimensional and Mounting Details

Circuit T (CT)

Feeds power through and taps desired circuit to other fixtures.

Typical MWS Wiring System Application shown utilizing Circuit T (CT).

T Cable

System View (not to scale)Dimensional and Mounting Details

T Cable (TC)

Consult MWS Installation, Application and Specification Manual for

additional comprehensive system information.

Drop Cable

System View (not to scale)Dimensional and Mounting Details

Drop Cable (DC)

Supplies power to out of system units. (Fixtures, J-boxes, etc.).

Typical MWS Wiring System Application shown utilizing Drop Cable (DC).

Front

Side

Extender Cable Extender CableT Cable

To p

Side

Drop Cable

Extender Cable

Junction Box

or any Out of

System Unit

supplied by

others.

Splitter or

Circuit T

To p

Right

2-1/4”

[57mm]

2-1/4”

[57mm]

2-1/4”

[57mm]

5-5/16”

[136mm]

5-5/16”

[136mm]

5/8”

[16mm]

1-7/8”

[47mm]

4-3/8”

[112mm]

1-13/16”

[45mm]

Circuit T

Extender Cable

Drop SO Cord Drop SO Cord

4

Consult MWS Installation, Application and Specification Manual for

additional comprehensive system information.

MWS IB519111EN Installation instructions

Installation Instructions – MWS 0-10V Dimming

Starter Fixture Cable

Dimensional and Mounting Details

Starter Fixture Cable (SF)

Fixture Fitting

System View (not to scale)Dimensional and Mounting Details

Fixture Fitting (FF)

Feeds power to fixture and allows circuits to be carried through to other fixture.

Locks into 1/2” KO of access plate, fixture body or J-box. The FF adds only 7/8”

to overall height of the fixture.

Typical MWS Wiring System Application shown utilizing (FF).

3/4” [19mm]

4-3/8”

[112mm]

Front

Side

To p

Quick Connect

Extender Cable Extender CableFixture Fitting

5-5/16”

[136mm]

2-1/4”

[57mm]

Front

Side

To p

Page is loading ...

Eaton

1121 Highway 74 South

Peachtree City, GA 30269

P: 770-486-4800

www.eaton.com/lighting

Canada Sales

5925 McLaughlin Road

Mississauga, Ontario L5R 1B8

P: 905-501-3000

F: 905-501-3172

Printed in USA

Imprimé aux États-Unis

Impreso en los EE. UU.

Publication No. IB519111EN

September 5, 2019

Eaton is a registered trademark.

All trademarks are property

of their respective owners.

Eaton est une marque de commerce

déposée. Toutes les autres marques

de commerce sont la propriété de leur

propriétaire respectif.

Eaton es una marca comercial

registrada. Todas las marcas

comerciales son propiedad de sus

respectivos propietarios.

Product availability, specifications,

and compliances are subject to

change without notice

La disponibilité du produit, les

spécifications et les conformités

peuvent être modifiées sans préavis

La disponibilidad de productos, las

especificaciones y los cumplimientos

están sujetos a cambio sin previo aviso

Conector de la luminaria

Vista del sistema (no a escala)Detalles dimensionales y de montaje

Conector de la luminaria (FF)

Alimenta a las luminarias y permite que los circuitos se transporten a otras

luminarias. Se bloquea en un orificio ciego de 1/2” de la placa de acceso, el

cuerpo de la luminaria o la caja de conexiones. El conector de la luminaria (FF)

agrega solo 7/8” a la altura total de la luminaria.

Aplicación típica del sistema de cableado MWS que se muestra utilizando el

conector de la luminaria (FF).

Conexión rápida

Cable de extensión Cable de extensión

Conector de la

luminaria

5-5/16"

[136 mm]

2-1/4"

[57 mm]

Frente

Lado

Parte superior

Warranties and Limitation of Liability

Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions.

Garanties et limitation de responsabilité

Veuillez consulter le site www.eaton.com/LightingWarrantyTerms pour obtenir les conditions générales.

Garantías y Limitación de Responsabilidad

Visite www.eaton.com/LightingWarrantyTerms para conocer nuestros términos y condiciones.

FCC Statement

Note: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Declaración de la FCC

Nota: Este equipo ha sido probado y cumple con los límites para un

dispositivo digital de Clase A, de conformidad con la parte 15 de las

Normas de la FCC. Estos límites están diseñados para proporcionar

una protección razonable contra interferencias perjudiciales cuando el

equipo se opera en un entorno comercial. Este equipo genera, utiliza y

puede emitir energía de radiofrecuencia y, si no se instala y utiliza de

acuerdo con el manual de instrucciones, puede causar interferencias

perjudiciales en las comunicaciones de radio. El funcionamiento

de este equipo en un área residencial puede causar interferencias

perjudiciales, en cuyo caso el usuario deberá corregir las interferencias

por su cuenta.

Instrucciones de instalación – Atenuación MWS 0-10V

Cooper Lighting CT Circuit T Installation guide

Cooper Lighting CT Circuit T Installation guide

in other languages

Related papers

Other documents