AMG Systems Ltd. reserves the right to make changes to this document without
notice. The information herein is believed to be accurate. No responsibility is
assumed by AMG for its use.
Page 1 of 5 AMG2743-SF Instruction
Sheet D15332-00
AMG2743-SF
Instruction Manual
Single Fibre Four Channel Video TX Unit with Bi-directional
Data
The AMG2743-SF is a standalone four channel video transmit unit designed to transmit four video
signals. It also provides one RS485/RS422.or RS232 bi-directional data channel. It is designed to be
powered from an AMG2002 power supply.
The AMG2743-SF is designed to operate with the AMG2744R-SF or AMG2744-SF four channel video
receivers and data transceiver requiring one fibre for operation of the video and bi-directional data.
Connections
Video Input Connection
Connector ..........................................75 ohm BNC Socket.
Input Impedance.................................75 ohm terminated.
Input Level..........................................1 volt p-p nominal
Frequency Response..........................10Hz to 5.75MHz min.
No of insert channels..........................4
Optical Connections
Connector...........................................FC/PC 1 off
OPTO OUT
Optical Launch Power.........................-5dBm
Wavelength.........................................1550nm
OPTO IN
Optical Sensitivity ...............................-22dBm
Wavelength.........................................1310nm
167mm Overall
155mm between mounting slot centres
(4mm slots)
122mm between
Slot Centres
132mm Overall
A
MG
2743-SF
4 CHANNEL VIDEO
TX
+
BI-DIRECTIONAL
DATA
TX O O RX
OPTO SYNC
FRONT PANEL INDICATORS
VIDEO PRESENT
CH1 O O CH2
CH3 O O CH4
POWER
O
GND
+12-16 Volts dc
OPTO IN →
VIDEO CH 1
VIDEO CH 2
VIDEO CH 3
VIDEO CH 4
OPTO OUT ←
GND
OUT-
OUT+
IN-
IN+
DATA
CONNECTIONS
INTERNAL
RS422/485
SWITCHABLE
*
TX O O RX
DATA PRESENT
AMG Systems Ltd. reserves the right to make changes to this document without
notice. The information herein is believed to be accurate. No responsibility is
assumed by AMG for its use.
Page 2 of 5 AMG2743-SF Instruction
Sheet D15332-00
Power Connection
Connector...........................................removable screw terminal connector (3.5mm spacing)
Manufacturers Part No. Phoenix/Combicom MC1-5/2-ST-3.5
AMG Part No.G00047-00
Power requirement .............................12 volts to 16 volt DC @
700mA (1 amp turn on
current)
Connections........................................See schematic
+12 – 16 Volts on lower pin
0 Volts on upper pin
Data Connections
Data Connector...................................5 way removable spring terminal connector (2.5mm spacing)
Manufacturers Part No. Phoenix/Combicom FK-MC-0.5/5-ST-
2.5
AMG Part No G15098-00
SW1 used to select between RS232 and RS485/422, SW2 is used to select between RS422 and
RS485.
NOTE: The unit is shipped from the factory as RS485 unless otherwise requested.
Connections RS422 4 wire .................See schematic
Connections RS485 4 wire .................See schematic
Connections RS232............................See schematic
•
•
•
•
•
OPTO IN D
A
T
A
CH 4 Channels 1 to 4
Pin 5 – Ground
Pin 4 – No Connection
Pin 3 – Data Out
Pin 2 – No Connection –
Pin 1 – Data In
•
•
•
•
•
•
•
OPTO IN D
A
T
A
CH 4
Power
Ground
+12 – 16 Volts dc
•
•
•
•
•
•
•
OPTO IN D
A
T
A
CH 4
Pin 5 – Ground
Pin 4 – Data Out –
Pin 3 – Data Out +
Pin 2 – Data In –
Pin 1 – Data In +
•
•
•
•
•
•
•
OPTO IN D
A
T
A
CH 4
Pin 5 – Ground
Pin 4 – No Connection
Pin 3 – No Connection
Pin 2 – Data In/Out –
Pin 1 – Data In/Out +
•
•
AMG Systems Ltd. reserves the right to make changes to this document without
notice. The information herein is believed to be accurate. No responsibility is
assumed by AMG for its use.
Page 3 of 5 AMG2743-SF Instruction
Sheet D15332-00
Protocol ..............................................RS232
SW1 switch position 9 on, switch position 10 on
SW2 all off
RS485 2wire
SW1 switch position 9 off, switch position 10 off
SW2 see below
RS422 4 wire Bus’ed or point to point
SW1 switch position 9 off, switch position 10 off
SW2 see below
See below for Configuration of the RS485 / RS422 data channel and description of tristate
operation
Each of the two data channels can be set up independently.
Indicators
Power.................................................Green – unit powered
Off – no power applied to unit
Opto Sync TX.....................................Green - optical channel transmitting
Off - optical channel not transmitting
Opto Sync RX.....................................Green - optical channel receiving
Off - optical channel not receiving
Video Present CH1.............................Green – video signal present on video CH1 input BNC
Off – no video present on video CH1 input BNC
Video Present CH2.............................Green – video signal present on video CH2 input BNC
Off – no video present on video CH2 input BNC
Video Present CH3.............................Green – video signal present on video CH3 input BNC
Off – no video present on video CH3 input BNC
Video Present CH4.............................Green – video signal present on video CH4 input BNC
Off – no video present on video CH4 input BNC
Data Present TX.................................Green – logic one present on the data input
Red – logic zero present on the data input
Off – tri-state off or no connection on the data input
This represents the data signals being transmitted on the optical fibre
Data Present RX.................................Green – logic one present on the corresponding data
output
Red – logic zero present on the data output
Off – tri-state off on the data output
This represents the data signals being received on the optical fibre
Physical Information
Dimensions
Height.................................................122mm
Width ..................................................167mm
Depth..................................................70mm
Weight ................................................800grams
AMG Systems Ltd. reserves the right to make changes to this document without
notice. The information herein is believed to be accurate. No responsibility is
assumed by AMG for its use.
Page 4 of 5 AMG2743-SF Instruction
Sheet D15332-00
Mounting Details
The unit is designed to mount into a panel via the four mounting slots of 4.5mm x 10mm.
Configuration of the RS422/485 Data Channel
The RS422/485 data channel can operate in two modes that are set by SW2 on the main PCB. (See
below for removal of the PCB and access to SW2)
Mode 1 – RS485 two wire half duplex transmission.
Mode 2 – RS422 four wire full duplex transmission. In this mode the RS422 output will transmit a
tristate condition as well as logic high and logic low for systems which require bus-ing of
the RS422 four-wire connection.
MODE Configuration Details SW2
position 1 SW2
position 2 SW2
position 3 SW2
position 4
1 RS-422 4 wire Point-to-Point -
and RS-422 BUS system OFF OFF OFF OFF
2 RS-485 2 wire BUS systems OFF ON ON ON
The data input for both the RS485 and the RS422 modes detects a tri-state input condition by
monitoring the differential voltage level across the input. A differential level below 500mV positive or
negative will be detected as a tristate condition. A level above 500mV positive or negative will be
detected as a logic 1 or logic zero respectively. It is important therefore to terminate the RS485
bus or the RS422 input bus using 120ohms if a pre-bias is present on the RS485 or RS422 bus.
A large number of third party equipment manufacturers apply a pre-bias on their RS485 bus. This pre-
bias is applied by pulling one arm of the RS485 bus high (+5 volts) and the other arm low (0 volts)
using high value resistors within the third party equipment. In order to ensure that a tri-state condition
is detected by the AMG2700 equipment, then these resistors should have a value above 1kohm.
SW1 Switch Settings
All SW1 switch settings are set at the factory as follows:
Switch
Position Description Setting
1 Video channel configuration OFF
2 Video channel configuration OFF
3 Video channel configuration OFF
4 Primary / Secondary Board Setting ON
5 Dual Redundant / Not dual redundant OFF
6 Not Used OFF
7 Not Used OFF
8 On board data / Separate data card ON
9 RS232 or RS422/485 OFF for
RS485/422
10 RS232 or RS422/485 OFF for
RS485/422
Removal From the Case
Note: - The 2700 PCB’s are static sensitive. Handle with proper care and use normal electrostatic
discharge (ESD) procedures. Use properly grounded protection (for example, wrist stamps) when
handling the PCB.
In order to remove the case (to access SW1 and SW2)
AMG Systems Ltd. reserves the right to make changes to this document without
notice. The information herein is believed to be accurate. No responsibility is
assumed by AMG for its use.
Page 5 of 5 AMG2743-SF Instruction
Sheet D15332-00
1.1. Loosen and remove the four screws on the top and bottom of the unit’s rear panel.
1.2. Slide the PCB assembly connected to the rear panel out of the case.
1.3. Ensure that the optical fibre is not trapped.
SW1 and SW2 can be found on the bottom right hand corner of each board and are labelled, close to
the rear panel. The switch position are labelled on the switch, switch position 1 is always the furthest
from the edge of the PCB.
When re-inserting the main PCB into the housing take care not to trap the optical fibre or the board
interconnection cables.
Fasten the rear panel with the screws.
Safety
The 2700 series of products uses a Class 1 laser system in accordance with EN 60825-2:2000.
However it is always advisable to follow good practice when working with optical fibre systems. This
includes:
Do not stare with unprotected eyes or with any unapproved collimating device at fibre ends or
connector faces, or point them at other people.
Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice associated with the optical fibres systems see EN
60825-2:2000 or your local safety officer.
Maintenance
There are no user serviceable parts within the AMG2700 products.
In case of problem or failure contact your local support centre or AMG Systems Ltd, Technical Support
Department on tel. +44 (0) 1767 600777.
See unit data sheet for full specification.
-
1
-
2
-
3
-
4
-
5
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
AMG AMG2644 Instruction Sheet
-
-
-
-
-
-
-
-
-
