Void INFINITE QX 4 Owner's manual

Type
Owner's manual

This manual is also suitable for

Void INFINITE QX 4 is a weight-carrying hitch designed for use with Infiniti QX4 and Nissan Pathfinder vehicles. It has a gross load capacity of 3,500 lbs. and a tongue weight of 300 lbs. The hitch is easy to install and does not require any drilling. It comes with all the necessary hardware and instructions. The hitch is also backed by a warranty from Curt Manufacturing Inc. Some possible use cases for the Void INFINITE QX 4 include:

  • Towing a trailer
  • Carrying a bike rack
  • Transporting cargo in a cargo carrier
  • Mounting a snowplow

Void INFINITE QX 4 is a weight-carrying hitch designed for use with Infiniti QX4 and Nissan Pathfinder vehicles. It has a gross load capacity of 3,500 lbs. and a tongue weight of 300 lbs. The hitch is easy to install and does not require any drilling. It comes with all the necessary hardware and instructions. The hitch is also backed by a warranty from Curt Manufacturing Inc. Some possible use cases for the Void INFINITE QX 4 include:

  • Towing a trailer
  • Carrying a bike rack
  • Transporting cargo in a cargo carrier
  • Mounting a snowplow
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
3,500 300
34
30
97-04 INFINITI QX4, 96-04 NISSAN PATHFINDER
2/23/2011
12179
60
367221
Parts List DESCRIPTIONPART NUMBERQTYITEM HEX BOLT
M12 - 1.25 x 40 HEX61 LOCK WASHER1/2"
62
1. Remove both the driver and passenger side tie down brackets bolted to the outside surface of the frame rails.
Return all removed parts to the vehicle owner for reinstallation should the hitch ever be removed.
NOTE: Loosen the spare tire and slide it forward to ease installation of the hitch.
2. Slide the hitch into position, aligning mounting holes to the existing weld nuts in the frame. Install fasteners
as shown.
3. Torque all 12mm fasteners to 65 lb-ft.
- REMOVE TIE DOWN BRACKETS
- NO DRILLING REQUIRED
- LOWER SPARE TIRE
2
1
EXISTING WELDNUTS (BOTH SIDES)
DRIVER SIDE FRAME RAIL
PASSENGER SIDE FRAME RAIL
DESIGNED FOR USE WITH
BALLMOUNT #55001 / 45501
  • Page 1 1

Void INFINITE QX 4 Owner's manual

Type
Owner's manual
This manual is also suitable for

Void INFINITE QX 4 is a weight-carrying hitch designed for use with Infiniti QX4 and Nissan Pathfinder vehicles. It has a gross load capacity of 3,500 lbs. and a tongue weight of 300 lbs. The hitch is easy to install and does not require any drilling. It comes with all the necessary hardware and instructions. The hitch is also backed by a warranty from Curt Manufacturing Inc. Some possible use cases for the Void INFINITE QX 4 include:

  • Towing a trailer
  • Carrying a bike rack
  • Transporting cargo in a cargo carrier
  • Mounting a snowplow

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI