Sunbox CT-2005 User manual

Brand
Sunbox
Model
CT-2005
Type
User manual

Sunbox CT-2005

The Sunbox CT-2005 Fiber Checker is a versatile tool for inspecting fiber optic cables and identifying faults or defects. It emits a 650nm red laser light that travels through the cable, and any breaks or damage will cause the light to refract and create a visible glow. The universal connector allows for testing of various fiber interfaces, including ST, SC, FC, and FDDA, and with an optional adapter, even 1.25mm fiber cables can be tested.

The CT-2005 features adjustable output modes, including continuous wave (CW) and pulse, providing different visual effects for fault detection. The range of visibility extends up to 5 kilometers, making it suitable for long-distance cable inspections. Additionally, the device incorporates a power circuit to ensure stable laser output even when the battery is low, and a dustproof cover prevents dust accumulation and accidental laser exposure.

Sunbox CT-2005

The Sunbox CT-2005 Fiber Checker is a versatile tool for inspecting fiber optic cables and identifying faults or defects. It emits a 650nm red laser light that travels through the cable, and any breaks or damage will cause the light to refract and create a visible glow. The universal connector allows for testing of various fiber interfaces, including ST, SC, FC, and FDDA, and with an optional adapter, even 1.25mm fiber cables can be tested.

The CT-2005 features adjustable output modes, including continuous wave (CW) and pulse, providing different visual effects for fault detection. The range of visibility extends up to 5 kilometers, making it suitable for long-distance cable inspections. Additionally, the device incorporates a power circuit to ensure stable laser output even when the battery is low, and a dustproof cover prevents dust accumulation and accidental laser exposure.

USER MANUAL
Rev 1.00
CT-2005
http://www.sunbox.com.tw
Tel: 886-2-82218189 Fax:886-2-82218190
CT-2005
- 1 -
Features
The CT–2005 Fiber Checker is used for checking the defects of a fiber cable. It sends a visible 650nm
wavelength red laser light through fiber optic cables, the breaks or faults in the fiber will refract the light,
creating a bright glow around the faulty area.
The universal connector can be used for the most common fiber interfaces such as ST/SC/FC/FDDA. It is
suitable to test both single–mode and multi–mode cables. With an optional 2.5mm to 1.25mm adapter,
users can even test for 1.25mm fiber cables.
The visibility is up to 5 kilometers. There is also a specially designed power circuit included; it
provides steady power which avoids unstable laser output when the battery is low.
The output signal can be switched between CW or Pulse mode to get different visual effects.
There is a dustproof cover which will prevent dust from getting into the inside of the interface.
The cover also helps avoid incidental exposure of the laser to your eyes.
APPEARANCES
1. Dustproof cover (a universal type fiber connector inside)
2. 3 Sections slide switch: CW/Pulse/Power Off
3. Power indicator
4. Pen–clip
CT-2005
- 2 -
SPECIFICATIONS
‧ Laser class: Class 2 laser product DIN EN 60825–1: 2007
‧ Wavelength: 650nm±10nm@25ºC
‧ Spectral width: <10nm
‧ Output Power:
>600µW@25ºC into 9µm fiber
‧ Mode: CW/Pulse
‧ Battery: AAA 1.5V X 2
‧ Indicator: Power/Battery low
‧ Output power reliable: +/– 0.2mW
‧ Spectral width: <10nm
‧ Range: Visibility to 5km
‧ Operating temp: 0 to 50ºC
‧ Storage temp: 0 to 70ºC
OPERATION
‧ Powered by two 1.5V AAA batteries.
‧ Lift the front dustproof up and insert the fiber cable to the universal connecter. Switch the slide
switch to CW or Pulse position, the power indicator LED lights green. (Red light represents power
low, please replace the batteries).
‧ A visible 650nm wavelength red laser is visible through the fiber optic cable, the breaks or faults in
the fiber will refract the light and create a bright glow around the faulty area.
‧ This product has been passed through FDA Laser safety certifications, but we still highly
recommend that you avoid any exposure to your eyes.
CAUTIONS
‧ Attention if the device is used for different fields of application as suggested, it may cause severe
harm through laser rays.
‧ Keep the device safely stored and out of the reach of children
‧ Never point the laser beam directed at persons
‧ Do not stare into the laser beam or the reflected laser beam
‧ If laser radiation enters the eye, the eyes are deliberately to be close and you＇re your immediately
away from beam
‧ Any manipulations (changes) to the laser device are prohibited
‧ These instructions are to be kept and to give forward when passing the laser device to another user
  • Page 1 1
  • Page 2 2
  • Page 3 3

Sunbox CT-2005 User manual

Brand
Sunbox
Model
CT-2005
Type
User manual

Sunbox CT-2005

The Sunbox CT-2005 Fiber Checker is a versatile tool for inspecting fiber optic cables and identifying faults or defects. It emits a 650nm red laser light that travels through the cable, and any breaks or damage will cause the light to refract and create a visible glow. The universal connector allows for testing of various fiber interfaces, including ST, SC, FC, and FDDA, and with an optional adapter, even 1.25mm fiber cables can be tested.

The CT-2005 features adjustable output modes, including continuous wave (CW) and pulse, providing different visual effects for fault detection. The range of visibility extends up to 5 kilometers, making it suitable for long-distance cable inspections. Additionally, the device incorporates a power circuit to ensure stable laser output even when the battery is low, and a dustproof cover prevents dust accumulation and accidental laser exposure.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents