2. B-K lighting
  3. Tree Strap - MB2

B-K lighting Tree Strap - MB2 Installation guide

  • I'm a chat assistant, and I've reviewed the installation instructions for the B-K Lighting MB2 Tree Strap. This document provides safety guidelines and step-by-step instructions for installing the fixture, including wiring and mounting, designed for use in wet locations and when mounted close to the ground. I'm here to help with your questions about this product.
  • What is the suitable mounting location for this product?
    What kind of wire connectors should I use?
    What should be done before wiring?
    What should I do if I need to replace the lamp?
TOOLS
NEEDED:
By Others
MB2
Tree Strap Installation
Warning Hot Surface
Installation Instructions
Waterproof Wire Connectors
High Voltage
RELEASED
4-14-15
REFERENCE NUMBER
INS-2137-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
NationalElectricalCode,CanadianElectricalCode,andallLocal
andProvincialCodes.
• Followproductlabelinformationandinstructions.
• QualifiedPersonnel mustperform allservicing orrelamping of
thisproduct.
• Beforewiringtopowersupplyandduringservicingorrelamping,
turnoffpoweratfuseorcircuitbreakerbeforeservice.
• The use of accessory equipment not recommended by the
manufacturerorinstalledcontrarytoinstructionsmaycausean
unsafecondition.Theuseofdamagedcomponentsmaycause
anunsafeconditionandvoidproductwarranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Donotblocklightemanatingfromproductinwholeorpart,
asthismaycauseanunsafecondition.
• Never operate the fixture with missing or damaged lens.
Lensmustbecleanedonregularbasis.
• Entire fixture may become extremely hot. Do not touch hot
lensorfixturebody.Donottouchthelampatanytime.Use
aclean,dry,softclothtohandlethelamp.Oilfromskinmay
damagethelampandcauseittorupture.
• Replace lamp only with correct wattage and type of lamp
markedonfixturelabel.
• All gaskets, o-rings and sealing surfaces must be kept clean
duringinstallationandservice;failuretodothismaycausean
unsafeconditionandvoidproductwarranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
LightedlampisHOT!
WARNING-ToreducetheriskofFIREORINJURYTOPERSONS:
Turnoff/unplugandallowtocoolbeforereplacinglamp.
LampgetsHOTquickly!Contactonlyswitch/plugwhen
turningon.
Donottouchhotlens,guard,orenclosure(seediagram/
picture).
Keeplampawayfrommaterialsthatmayburn.
Donotouchthelampatanytime.Useasoftcloth.Oil
fromskinmaydamagelamp.
Donotoperatetheluminairefittingwithamissingor
damagedshield.
SAVE THESE INSTRUCTIONS
· Suitable for wet location · Additionally suitable for mounting within 4 ft. of the ground
IMPORTANT LISTINGS AND CERTIFICATIONS
MB2
 Canopy
(Specify Canopy,
Cover and/or Fixture
Separately)
Tree Strap
(Specify Strap Length
Separately)
Installation Instructions
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
4-14-15
REFERENCE NUMBER
INS-2137-00
Installation
2. Runconduit(ByOthers)toMB2boxlocation.
MB2boxhasfour(4) 1/2” NPStappedholes.
Ensure unused tapped holes are plugged.
Plugsareprovided.
1. Remove canopy and/or fixture from MB2
housing. Use adjustable strap provided to attach
MB2 housing to tree. Tighten by pulling on the
adjustablestrapuntilsecure.
GroundHotNeutral
4. Place wire connectors and/or power supply inside
MB2box,thensecurecanopyand/orfixturetoMB2.
3. PullwiringtoMB2boxlocation.Usewaterproof
wire connectors to connect incoming primary
wiring to power supply. Connect incoming
groundwiringtogroundconductorinhousing.
See wiring diagram.
WIRING DIAGRAM
LINE (+)
FIXTURE
COM
WIRING DIAGRAM
POWER
SUPPLY
(-)
GROUND GROUND
MB2
Tree Strap Installation
/