Bosch SE64A631GB/01 Brief description

Type
Brief description
Brief Instructions: Dishwasher
Short and handy: everything
your dishwasher needs...
Before using for the first
time, read the Installation
and Operating Instructions!
Switch appliance ON, off we go...
Press main switch, choose programme.
Close door.
Signal sounds, open door. End-of-programme
indicator flashes, press main switch.
Switch appliance OFF, everything OK...
Add rinse-aid.
Add detergent.
Select programme.
Add salt.
5600 053 469  
en
Setting the water softening system *
Quickly sorted
Find out the water
hardness at your water
utility company and
enter below
* only before using the
dishwasher for the first
time or if the water hard-
ness changes
Read off the setting
SettingdH fH Clarke mmol/l
and then select a setting
– Hold down programme button B and switch on the main
switch, then release the buttons. The . display flashes and
buttons A and B illuminate (water hardness setting was set
to 2 at the factory).
– Each time button B is depressed, the setting increases by
one (0-3). If buttons A, B and C illuminate, the maximum
water hardness setting has been reached. If the water
hardness setting is now increased again, the lights go out
and the water hardness setting is set to 0.
– Switch off the main switch. The selected setting has been
stored in the appliance.
0
1
2
3
Reset
ABC
22–35
0–6
7–16
17–21
0–1,1
1,2–2,9
3,0–3,7
3,8–6,2
9–20
0–11
12–29
30–37
38–60
0–8
21–26
27–44
Dissolves limescale (not required for set value 0!)
Unscrew
the lid.
Only before using
the dishwasher
for the first time
pour approx. 1 l /
1 1/4 pt water into
the salt opening.
Pour in max.
1.5 kg / 3 lb 5 oz
salt (never deter-
gent!)
Screw on the
lid. Switch on
dishwasher
immediately.
Everything is sparkling clean ... Refill whenever level indicator is light!
Press mark 1,
lift up lid 2.
Pour in
rinse aid.
Close the
lid. CLICK!
Very dirty dishes, a lot of detergent ...
If required, open
the lid (press the
pin).
Warning,
combination
products are not
suitable for all
programmes,
follow manufac-
turers instructions.
Pour in
detergent.
Push the lid
shut, press.
PLOP!
Quick, economical or intensive ...
This overview indicates the max. possible number of
programmes. The programmes which correspond to your
appliance can be found on your appliance fascia.
The programme data are values measured in the
laboratory in compliance with Standard EN 50242.
Deviations is practice are possible.
Overview of programmes
120
1,70
20
125
1,24
18
90
0,90
16
35
0,70
12
15
0,10
5
35 50 70 65 40
Duration in minutes
Power consumption in kWh
Water consumption in litres
Intensive
Normal Eco Gentle
Quick Prerinse
125
1,45
19,5
Maintenance and care
For perfect rinsing results
Filters
Check and,
if required,
clean:
Rotate filter cylinder,
remove filter system
Rinse under
running water
Insert Screw on filter
system.
NOTE MARK!
Spray arms
Remove blockages/
deposits
Pull up lower arm Unscrew upper arm Clean under running
water (if required, use
a toothpick)
Insert lower arm Screw on upper arm
Breakdown and assistance
The correct procedure
Problem Possible causes Remedy
Water left in the appliance
Appliance not working/
stopst ...
Appliance not working/
stops ...
The crockery is
not clean ...
There are powdery or
greasy residues on the
crockery ...
The appliance was opened
during the programme ...
No / too little water
check whether ...
Crockery is stacked too closely
together/on top of each other ...
Too little cleaning agent ...
Wrong programme ...
The spray arms are obstructed
The filter is loose ...
The filter is dirty ...
The spray arm nozzles are
blocked ...
Too little water ...
Close the appliance and switch
it on, or stop the programme
(see Stopping the programme).
the water supply is turned on.
the supply fittings are not
obstructed or furred up.
the supply hose is not bent.
Reload according to the
instructions.
Refer to the manufacturer’s
instructions.
Select the appropriate
programme.
Rearrange items causing a
blockage (e.g. large spoons).
Clean the filter (see above)
secure the filter correctly
(MARKING).
Clean the filter (see above).
Clean the spray arms (see above).
See “Appliance is no longer
working”.
Problem Possible causes Remedy
Plastic parts/crockery
discoloured ...
Use a milder cleaning agent ...
Too little cleaning agent ...
Use a cleaning agent containing
chlorine bleach.
Refer to the manufacturer’s
instructions.
Milky deposits on
the crockery
(removable) ...
Glasses
cloudy/dull ...
Rust on the
cutlery ...
Rinsing agent dose too high
(streaks visible) ...
Rinsing agent dose too
low ...
Water too hard ...
Glasses not dishwasher-proof ...
Unsuitable cleaning agent ...
Cutlery not
rustproof ...
Reduce or increase the dosage
according to the instructions.
Refill the special salt/
adjust water softening system.
Use dishwasher-proof
glasses.
Use a glass-enhancing
cleaning agent.
Use dishwasher-proof cutlery.
You will find further information in the instructions for use ...
you may be able to solve the problem yourself.
Interrupting the programme ... Terminating the programme ...
Arranging dishes correctly ...
Open the door.
Press the two RESET
buttons simultaneously
(approx. 3 seconds)
(RESET).
Close the door.
Open the door.
Press the START/STOP
button.
To continue, press the
START/STOP button again.
Close the door.
Switch off the
appliance.
After 1 minute the
programme ends.
The ”signal
sounds and the
standby indicator
illuminates”.
Arrange dishwasher-proof dishes in accordance with the operating manual
(without residual ash, wax, lubricating grease, ink, sticky labels; remove any
large remnants of jam, milk products or food) and check that the spray arms
can rotate freely.
  • Page 1 1
  • Page 2 2

Bosch SE64A631GB/01 Brief description

Type
Brief description

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI