Da-Lite 27963 is a versatile panoramic projection screen system designed to deliver stunning visuals for various applications. With its three-panel design, it offers a wide viewing area and accommodates different screen sizes. The screen features a sturdy frame construction, ensuring stability and durability during installation and use. The included seam brace helps maintain optimal alignment between the panels, resulting in a seamless viewing experience. The screen's adaptability allows for mounting on various wall types using the provided wall brackets.
Da-Lite 27963 is a versatile panoramic projection screen system designed to deliver stunning visuals for various applications. With its three-panel design, it offers a wide viewing area and accommodates different screen sizes. The screen features a sturdy frame construction, ensuring stability and durability during installation and use. The included seam brace helps maintain optimal alignment between the panels, resulting in a seamless viewing experience. The screen's adaptability allows for mounting on various wall types using the provided wall brackets.
INSTRUCTION BOOK FOR
IDEA™ Panoramic
2
Preparation
Note: It requires at least four people to assemble an IDEA
Panoramic. To maintain optimal projected image geometry and
screen alignment, a lat and straight wall free from obstructions
and angular distortions should be used.
Tools Required For Assembly
Phillips Screwdriver
Level
Rubber Mallet
Measuring Tape ⅜” Open Wrench
or Socket Driver
Hardware Provided
#8 x ½” Screws
Number of supplied screws
varies by screen size
44” Wall Bracket
Number of supplied brackets varies by screen size. See Table 1.
28” Wall Bracket
Number of supplied brackets varies by screen size. See Table 1.
18” Wall Bracket
Number of supplied brackets varies by screen size. See Table 1.
(2) Seam Brace
(6) LBrackets (8) 1032 Nuts
Choose a clean work area for assembly using padded material or
other soft, clean materials. The work area should be larger than
the overall screen size and directly in front of the location where
the screen is to be installed.
3
Wall Brackets Included
Item Number Overall Dimensions
Center Panel Viewing Area
(H x W)
Center Panel Wall Brackets Side Panel Wall Brackets
27966 36¾" x 144¾" 36" x 64" (2) 28" (2) 28"
27981 36¾" x 144¾" 36" x 57½" (2) 28" (2) 28"
27963 46¾" x 144¾" 46" x 81¾" (2) 28" (2) 28"
27978 46¾" x 144¾" 46" x 73½" (2) 28" (2) 28"
27960 50¾" x 144¾" 50" x 89" (2) 44" (2) 18"
27975 50¾" x 144¾" 50" x 80" (2) 28" (2) 28"
27957 53¾" x 144¾" 53" x 94¼" (2) 44" (2) 18"
27972 53¾" x 144¾" 53" x 84¾" (2) 28" (2) 28"
27954 60¼" x 144¾" 59½" x 106" (2) 44" (2) 18"
27969 60¼" x 144¾" 59½" x 95¼" (2) 44" (2) 18"
27965 36¾" x 168¾" 36" x 64" (2) 28" (2) 44"
27980 36¾" x 168¾" 36" x 57½" (2) 28" (2) 44"
27962 46¾" x 168¾" 46" x 81¾" (2) 28" (2) 28"
27977 46¾" x 168¾" 46" x 73½" (2) 28" (2) 44"
27959 50¾" x 168¾" 50" x 89" (2) 44" (2) 28"
27974 50¾" x 168¾" 50" x 80" (2) 28" (2) 44"
27956 53¾" x 168¾" 53" x 94¼" (2) 44" (2) 28"
27971 53¾" x 168¾" 53" x 84¾" (2) 28" (2) 28"
27953 60¼" x 168¾" 59½" x 106" (2) 44" (2) 28"
27968 60¼" x 168¾" 59½" x 95¼" (2) 44" (2) 28"
27964 36¾" x 192¾" 36" x 64" (2) 28" (2) 44"
27979 36¾" x 192¾" 36" x 57½" (2) 28" (2) 44"
27961 46¾" x 192¾" 46" x 81¾" (2) 28" (2) 44"
27976 46¾" x 192¾" 46" x 73½" (2) 28" (2) 44"
27958 50¾" x 192¾" 50" x 89" (2) 44" (2) 44"
27973 50¾" x 192¾" 50" x 80" (2) 28" (2) 44"
27955 53¾" x 192¾" 53" x 94¼" (2) 44" (2) 44"
27970 53¾" x 192¾" 53" x 84¾" (2) 28" (2) 44"
27952 60¼" x 192¾" 59½" x 106" (2) 44" (2) 28"
27967 60¼" x 192¾" 59½" x 95¼" (2) 44" (2) 44"
Table 1
Hardware Provided
4
Assembly Instructions for Panoramics with 24” Marker Tray
1. Carefully unpack unit and place all panels on top of the clean
work area. The viewing surface of each panel must face down.
NOTE: For optimal seam alignment, use labels on the back side of
each panel to arrange for assembly.
2. Slide all three panels together, aligning the both the top and
bottom frames (Figure 1).
3. Find (1) seam brace and remove the release liner from both strips
of adhesive tape.
4. Ensuring that the panels are still in alignment, line up the seam
brace with one of the panel seams with adhesive side facing
down. Do not press adhesive into panels yet. Maintain at least a
small gap between the adhesive and the panel.
Figure 1
Figure 2
5. Use ⅜” open wrench or socket driver and (4) 1032 nuts to attach
seam brace onto the studs on the top and bottom of screen
frame at the panel seam. Tighten all four nuts once attached to
the frame (Figure 2).
NOTE: For optimal seam alignment, hold the panels together
tightly while the seam brace is being adhered and the lock nuts
are being tightened.
6. Press adhesive into panels. Apply steady pressure along the
length of the seam brace to attach irmly.
7. Repeat Steps 36 to attach the other seam brace.
1032 Nuts
Seam Braces
5
Wall Mounting for Panoramics with 24” Marker Tray
NOTE: The screen is shipped with four wall brackets and lengths
shipped vary by screen size. Two brackets will be used on the
center panel and one bracket on each of the side panels.
Measure gap on each side panel to determine which two
brackets will be used with these panels. These brackets will be of
an equal length. The remaining two brackets (also of an equal
length) will be used to hold the weight of the center panel. Use
appropriate mounting hardware for the wall type and to
accommodate for the screen’s total hanging weight.
1. Secure the two center panel wall brackets to wall studs at the
desired height. The outside edge of each wall bracket must be
no greater than 5” away from the left or right panel seams. You
will need at least 1” clearance above the drilled holes to hang the
screen.
2. Secure the two side panel wall brackets to wall studs at the height
selected in Step 1. Each side panel wall bracket should be
centered between the seam brace and left or right outside edge
of the frame when mounted to the wall (Figure 3).
NOTE: Do not proceed if all four brackets are not level with each
other or a gap may appear between each of the panels when
mounted.
3. To install the (2) center panel L-brackets, you must measure the
overall height of the screen frame and subtract 1 1/8”. Using that
dimension, measure down from the top edge of each of the
center wall brackets and mark the wall for two screw holes. The
outside edge of each center panel L-bracket must be no greater
than 5” away from the left or right panel seams (Figure 3).
4. Secure the two center panel L-brackets to the wall at the marked
locations. The longest side of the two center panel L-brackets
should be pointing upwards when secured in order to hide the
L-brackets behind the screen frame once the screen is installed
(Figure 3).
Wall Brackets
LBracket
No More
than 5”
No More
than 5”
No More
than 5”
Screws (Not Supplied)
Tray Installed in Step 8
Figure 3
6
Wall Mounting Instructions for Screens with 24” Marker Tray (continued)
5. Repeat Steps 34 to install the (4) remaining L-brackets for the side
panels.
NOTE: At this point, all six L-brackets will be mounted on the wall;
two L-brackets for each panel. Do not proceed if all six-L brackets
are not level with each other on the wall.
Steps 67 require at least four people. Place one person on the
far left end of the screen, one person at the left panel seam,
one person at the right panel seam and one person on the far
right end of the screen. More people can be utilized as
needed. When lifting the screen of of the clean work area to
the wall and then onto the wall, it is crucial that the screen
remain coplanar and does not bend at the seams.
CAUTION: Any bend between the three panels at the seams
may damage the screen or result in a permanent gap
between the seams.
6. Using all four people, carefully lift the fully assembled three panel
screen to an upright position and place underneath the mounted
wall and L-brackets. The screen will be parallel to the wall at the
end of this step.
7. Using all four people, carefully and in a smooth motion lift the
screen to hang it on the four installed wall brackets. There is a lip
on the back of the frame that wedges itself into the four wall
brackets once full installed. Ensure that the screen clears the six
L-brackets and that the screen weight is on the four wall brackets,
not the six L-brackets.
8. Center the aluminum tray to the bottom of the center panel
frame and attach with (3) of the provided #8 x ½” screws. Insert
screws through the tray into the groove (Figure 4).
9. Tap the bottom of the six L-brackets with the rubber mallet until
they make contact with the frame. Secure the six L-brackets to the
frame with the remaining (12) #8 x 1/2” screws (Figure 4).
Figure 4
#8 X ½" Screws
#8 X ½" Screws
7
Assembly Instructions for Panoramics with Full Length Marker Tray
1. Carefully unpack unit and place all panels on top of the clean
work area. The viewing surface of each panel must face down.
NOTE: For optimal seam alignment, use labels on the back side
of each panel to arrange for assembly.
2. Slide all three panels together, aligning the both the top and
bottom frames (Figure 5).
3. Find (1) seam brace and remove the release liner from both strips
of adhesive tape.
4. Ensuring that the panels are still in alignment, line up the seam
brace with one of the panel seams with adhesive side facing
down. Do not press adhesive into panels yet. Maintain at least a
small gap between the adhesive and the panel.
5. Use ⅜” open wrench or socket driver and (4) 1032 nuts to attach
seam brace onto the studs on the top and bottom of screen
frame at the panel seam. Tighten all four nuts once attached to
the frame (Figure 6).
NOTE: For optimal seam alignment, hold the panels together
tightly while the seam brace is being adhered and the lock nuts
are being tightened.
`6. Press adhesive into panels. Apply steady pressure along the
length of the seam brace to attach irmly.
7. Repeat Steps 36 to attach the other seam brace.
Figure 5
Figure 6
1032 Nuts
Seam Braces
8
Figure 7
Wall Mounting for Panoramics with Full Length Marker Tray
NOTE: The screen is shipped with four wall brackets and lengths
shipped vary by screen size. Two brackets will be used on the
center panel and one bracket on each of the side panels.
Measure gap on each side panel to determine which two
brackets will be used with these panels. These brackets will be of
an equal length. The remaining two brackets (also of an equal
length) will be used to hold the weight of the center panel. Use
appropriate mounting hardware for the wall type and to
accommodate for the screen’s total hanging weight.
1. Secure the two center panel wall brackets to wall studs at the
desired height. The outside edge of each wall bracket must be no
greater than 5” away from the left or right panel seams. You will
need at least 1” clearance above the drilled holes to hang the
screen.
2. Secure the two side panel wall brackets to wall studs at the
height selected in Step 1. Each side panel wall bracket should be
centered between the seam brace and left or right outside edge
of the frame when mounted to the wall (Figure 7).
NOTE: Do not proceed if all four brackets are not level with each
other or a gap may appear between each of the panels when
mounted.
Wall Brackets
No More
than 5”
No More
than 5”
Screws (Not Supplied)
9
Steps 38 require at least four people. Place one person on the
far left end of the screen, one person at the left panel seam,
one person at the right panel seam and one person on the far
right end of the screen. More people can be utilized as
needed. When lifting the screen of of the clean work area to
the wall and then onto the wall, it is crucial that the screen
remain coplanar and does not bend at the seams.
CAUTION: Any bend between the three panels at the seams
may damage the screen or result in a permanent gap
between the seams.
3. Using all four people, carefully lift the fully assembled three panel
screen to an upright position and then place back on the clean
work area with the viewing surface of each panel facing up.
4. Align the center panel tray section with the center panel ensuring
the tray edges align with the panel seams.
5. Secure the center panel tray section to the center panel with the
provided #8 x ½” screws (Figure 8).
6. Repeat Steps 45 to attach the left and right tray sections to the
left and right panels.
NOTE: Straight and even alignment of the tray sections will
maintain rigidity of the screen assembly when installed on the
wall.
Wall Mounting for Panoramics with Full Length Marker Tray (continued)
Viewing Surface
Aluminum Tray
#8 X ½" Screws
Figure 8
10
Wall Mounting for Panoramics with Full Length Marker Tray (continued)
7. Using all four people, carefully lift the fully assembled three panel
screen with the marker trays to an upright position and briely
place underneath the mounted wall brackets. The screen will be
parallel to the wall at the end of this step.
8. Using all four people, carefully and in a smooth motion lift the
screen to hang it on the four installed wall brackets. There is a lip
on the back of the frame that wedges itself into the four wall
brackets once full installed. Ensure that the screen weight is on
the four wall brackets.
9. To complete your installation, secure the screen to the wall
through the holes in the marker trays (Figure 9).
Figure 9
Screws
(Not Supplied)
11
Cleaning
The supplied cleaning cloth can be used to clean marks on the screen surface made by everyday dry erase marker usage. Use clean or
dry sections of the microiber cloth when erasing the screen. This is important to prevent smearing on the screen while cleaning. To
clean persistent marks from dry erase markers, use the supplied Da-Lite spray cleaner and cleaning cloth. Windex Original spray cleaner
can be used to remove tough to clean or smeared areas. To clean permanent markers and other unintentional marks on the surface,
use the supplied Da-Lite spray cleaner and cleaning cloth or a melamine foam cleaning pad.
LIMITED ONE YEAR WARRANTY ON DALITE PRESENTATION PRODUCTS
Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects
in materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are
properly operated according to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment
from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered
with or repaired by a person other than authorized Da-Lite personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.
Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,
transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.
To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of
itness for use, or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period.
This warranty gives you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM
EXTENT PERMITTED BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM
INTERRUPTION IN OPERATION OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137,
Warsaw, IN 465810137, (574) 2678101, (800) 6223737.
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DALITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS
WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DALITE WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.
28408
A Milestone AV Technologies Brand
3100 North Detroit Street
Warsaw, Indiana 46582
P: 574.267.8101 or 800.622.3737
F: 574.267.7804 or 877.325.4832
www.da-lite.com
DL–0489 (Rev 4) 02.15
© 2015 Milestone AV Technologies LLC. Printed in U.S.A.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Da-Lite 27963 User manual
- Category
- Projection screens
- Type
- User manual
Da-Lite 27963 is a versatile panoramic projection screen system designed to deliver stunning visuals for various applications. With its three-panel design, it offers a wide viewing area and accommodates different screen sizes. The screen features a sturdy frame construction, ensuring stability and durability during installation and use. The included seam brace helps maintain optimal alignment between the panels, resulting in a seamless viewing experience. The screen's adaptability allows for mounting on various wall types using the provided wall brackets.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Epson 100in. Da-Lite IDEA Screen for Projection and Dry-erase Installation guide
-
Fletcher-Terry 09-208 User manual
-
SIG SIGRC65 User manual
-
-
Winflo IR002B30GF Installation guide
-
-
Winflo IR002B30GF Installation guide
-
AeroWorks .90-1.20 YAK 54 ARF-QB Assembly Manual
-
Procolor 095020 Datasheet
-
Winflo IR001C36SRF User manual
