Honey-Can-Do GAR-01506 Installation guide
- Category
- Computer desks
- Type
- Installation guide
ASSEMBLY INSTRUCTIONS
INSTRUCTIONS
honey-can-do international 5750 McDermott Drive, Berkeley, IL 60163 USA tele 877.242.2636 www.honeycando.com
(QTY) DESCRIPTION ILLUSTRATIONPART
DIMENSIONS
ITEM #
LIMITED LIFETIME WARRANTY
This product is warranted to be free of defects in material and workmanship for as long as the
consumer owns the product. At Honey-Can-Do’s option, defective product will be repaired,
replaced or substituted with a product of equal value. For warranty service, e-mail Honey-Can-Do
at [email protected] or call at (877) 242-2636. You may also contact Honey-Can-Do
at 5750 McDermott Drive, Berkeley, IL 60163. Do not dispose of the defective item until or unless
you are specifically asked to do so by Honey-Can-Do as we may require return of the defective
item. Honey-Can-Do shall in no event be liable for any incidental or consequential damages.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above exclusion may not apply to you. This warranty gives you specific legal rights, and you
may also have additional rights, which may vary from state to state.
heavy-duty
garment rack
GAR-01506
35.12-59.37 in H x 21 in W x 51.12-66.25 in D
(66 cm H x 66 cm W x 15.2 cm D)
©2013 honey-can-do international, llc | all rights reserved - 121226
IMPORTANT! Plead read prior to use. This chrome garment rack is
designed for indoor use. Please do not over-load. To prevent tipping,
we recommend that you evenly distribute the weight throughout
the unit.
Please do not use garment rack for anything other than its intended use.
Please do not allow children, spouses or pets to hang from or hide in
storage closet. Please keep away from heat sources such as heaters
and fireplaces.
For assistance, please contact us at [email protected] or 877.2.I.Can.Do.
Thank you for purchasing our chrome garment rack. Please follow these
step-by-step instructions. Please plan to spend about 10 minutes assembling
your new garment rack.
1. Position the side components (A) so that the adjustment holes are facing
each other. Attach the horizontal poles (B) to the side components (A) by
running screws (H) through the side components (A) and into the horizontal
poles (B). Tighten with the hex wrench (J).
2. Turn the unit on its side. Screw the casters (G) into the threaded holes
on the bottoms of the side components (A). Tighten with the wrench (J).
Return the unit to an upright position.
3. Press the spring pins on the vertical poles (C) and slide the ends into the
side components (A) until the spring pins pop through the upper adjusting
holes on the side components (A). To adjust the height of the rack, press
both spring pins and raise or lower the vertical poles (C) until the spring
pins pop through the holes at the desired height. Fit the expanding
hanging pole (D) onto the vertical poles.
4. Place the shelf (E) onto the base of the garment rack.
G
(2) side components
(2) horizontal poles
(2) vertical poles
(1) expanding
hanging pole
(1) shelf
F
(4) casters
G
(4) screws
H
(1) hex wrench
I
(1) wrench
D
H
I
adjustment hole
G
J
-
1
Honey-Can-Do GAR-01506 Installation guide
- Category
- Computer desks
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Honey-Can-Do SFT-01466 Operating instructions
-
-
-
-
-
-
-
-
Unbranded GAR-01119 User manual
-
