Graco 309640A Owner's manual

Graco
Brand
Graco
Model
309640A
Category
Paint Sprayer
Type
Owner's manual

This manual is also suitable for

Graco 309640A RACX Handtite Guard is a patented aerodynamically designed guard that virtually eliminates paint buildup. It can be hand tightened on the gun without requiring any tools and fits all Graco airless spray guns, but it is recommended to be used with RACX series SwitchTips only. It helps to prevent the undirected spray of fluid into the eyes or on the skin of the operator, as the spray tip should always be kept clear to avoid any fluid injection or splashing. The maximum working pressure of the Graco 309640A RACX Handtite Guard is 4050 psi (280 bar, 28 MPa).

Graco 309640A RACX Handtite Guard is a patented aerodynamically designed guard that virtually eliminates paint buildup. It can be hand tightened on the gun without requiring any tools and fits all Graco airless spray guns, but it is recommended to be used with RACX series SwitchTips only. It helps to prevent the undirected spray of fluid into the eyes or on the skin of the operator, as the spray tip should always be kept clear to avoid any fluid injection or splashing. The maximum working pressure of the Graco 309640A RACX Handtite Guard is 4050 psi (280 bar, 28 MPa).

WARNING
To reduce the risk of fluid injection or splashing in the eyes or on the skin, relieve air and fluid pressure in the system before installing, cleaning or
changing tips. See Pressure Relief Procedure in gun or sprayer manual.
S Keep clear of spray tip. High-pressure spray or leaks can inject fluid into the body, resulting in serious injury which may
require amputation. Never spray without a tip guard (D).
S Do not exceed 4050 psi (280 bar, 28 MPa) maximum working pressure.
Failure to install or use the RACt tip guard assembly correctly may result in an undirected spray of fluid into the eyes or on the skin of the operator.
Be sure you:
S Fully insert SwitchTip (A) into tip bore (C) in guard
S Do not trigger gun with SwitchTip handle between Spray and Clear positions
S Replace OneSealt when replacing worn SwitchTip
B
A
C
D
Insert SwitchTip in tip bore and firmly thread
assembly onto gun
Use SwitchTip handle to remove OneSeal
from tip guard
Clearing a Clogged SwitchTip
Disassembling
Engage gun safety and rotate
SwitchTip handle to Clear posi-
tion
12 34
12
Disengage gun safety and trigger
gun into pail to clear SwitchTip
Engage gun safety and rotate
SwitchTip handle to Spray posi-
tion
Disengage gun safety and trigger gun
into pail to verify SwitchTip is clear
Note:If SwitchTip is still clogged, follow Pressure Relief Procedure in gun or sprayer manual, and remove SwitchTip for
cleaning.
Clear
position
Spray
position
Use end of SwitchTip (A) to press OneSeal
(B) into tip guard (D), with curve matching tip
bore (C)
Installing
ti2508a
Instructions
RACX HandTitet Guard
Model 246215, Series A, 7/8 in. Guard
4050 psi (280 bar) Maximum Working Pressure
Model 246437, Series A, 11/16 in. Guard
4050 psi (280 bar) Maximum Working Pressure
D Patented aerodynamic design virtually eliminates paint buildup.
D Hand tighten on gun–no tools required.
D Fits all Graco airless spray guns.
D Use with RACX series SwitchTips only.
D Graco RACX SwitchTip sold separately.
309640A
2 309641
Graco Phone Number
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to
you: 1-800-690-2894 Toll Free
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
ECOPYRIGHT 2002, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
Printed in USA 309641 October 2002
  • Page 1 1
  • Page 2 2

Graco 309640A Owner's manual

Graco
Brand
Graco
Model
309640A
Category
Paint Sprayer
Type
Owner's manual
This manual is also suitable for

Graco 309640A RACX Handtite Guard is a patented aerodynamically designed guard that virtually eliminates paint buildup. It can be hand tightened on the gun without requiring any tools and fits all Graco airless spray guns, but it is recommended to be used with RACX series SwitchTips only. It helps to prevent the undirected spray of fluid into the eyes or on the skin of the operator, as the spray tip should always be kept clear to avoid any fluid injection or splashing. The maximum working pressure of the Graco 309640A RACX Handtite Guard is 4050 psi (280 bar, 28 MPa).

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents