Hotpoint WM1510W Owner's manual

Page is loading ...

33502009GB.fm Page 15 Tuesday, October 27, 2009 12:58 PM

BEFORE USING THE APPLIANCE

• This appliance is intended to be used in

household and similar applications such as

- staff kitchen areas in shops, offices and other

working environments;

- farm houses and by clients in hotels, motels and

other residential type environments;

- bed and breakfast type environments.

To ensure best use of your appliance, carefully

read the operating instructions which contain

a description of the product and useful advice.

Keep these instructions for future reference.

1. After unpacking the appliance, make sure it is

not damaged and that the door closes properly.

Any damage must be reported to the dealer

within 24 hours of delivery of the appliance.

2. Wait at least two hours before switching the

appliance on, to ensure that the refrigerant

circuit is fully efficient.

3. Installation and the electrical connection must be

carried out by a qualified technician according to

the manufacturer’s instructions and in

compliance with the local safety regulations.

4. Clean the inside of the appliance before using it.

1. Packing

The packing material is 100% recyclable and bears

the recycling symbol . For disposal, comply with

the local regulations. Keep the packing materials

(plastic bags, polystyrene parts, etc.) out of the

reach of children, as they are a potential source of

danger.

2.

Scrapping/Disposal

The

appliance is manufactured using recyclable

material.

This appliance is marked in compliance with

European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE). By

ensuring the correct disposal of this appliance, you

can help prevent potentially negative consequences

for the environment and the health of persons.

The symbol on the appliance, or on the

accompanying documents, indicates that this

appliance should not be treated as domestic waste

but must be taken to a special collection centre for

the recycling of electrical and electronic equipment.

When scrapping the appliance, make it unusable by

cutting off the power cable and removing the doors

and shelves so that children cannot easily climb

inside and become trapped.

Scrap the appliance in compliance with local

regulations on waste disposal, taking it to a special

collection centre; do not leave the appliance

unattended even for a few days, since it is a

potential source of danger for children.

For further information on the treatment, recovery

and recycling of this product, contact your

competent local office, the household waste

collection service or the shop where you

purchased the appliance.

Information:

This appliance does not contain CFCs. The

refrigerant circuit contains R134a (HFC) or R600a

(HC) (see the rating plate inside the appliance).

Appliances with Isobutane (R600a): isobutane is a

natural gas

without environmental impact, but is

flammable.

Therefore, make sure the refrigerant

circuit pipes are not damaged.

This product may contain Fluorinated Greenhouse

Gases covered by the Kyoto Protocol; the

refrigerant gas is inside a hermetically sealed

system.

Refrigerant gas: R134a has a Global Warming

Potential of (GWP) 1300.

Declaration of conformity

• This appliance has been designed for preserving

food and is manufactured in compliance with

Regulation (CE) No. 1935/2004.

• This appliance has been designed, manufactured

and marketed in compliance with:

- safety objectives of the “Low Voltage”

Directive 2006/95/CE (which replaces

73/23/CEE and subsequent amendments);

- the protection requirements of Directive

“EMC” 2004/108/EC.

Electrical safety of the appliance can only be

guaranteed if it is correctly connected to an

approved earthing system.

SAFEGUARDING THE ENVIRONMENT

13

33502009GB.fm Page 16 Tuesday, October 27, 2009 12:58 PM

INSTALLATION

• The appliance must be handled and installed by

two or more persons.

• Be careful not to damage the floors (e.g.

parquet) when moving the appliance.

• During installation, make sure the appliance does

not damage the power cable.

• Make sure the appliance is not near a heat

source.

• To guarantee adequate ventilation, leave a space

on both sides and above the appliance and follow

the installation instructions.

• Keep the appliance ventilation openings free.

• Do not damage the appliance refrigerant circuit

pipes.

• Install and level the appliance on a floor strong

enough to take its weight and in a place suitable

for its size and use.

• Install the appliance in a dry and well-ventilated

place. The appliance is arranged for operation in

places where the temperature comes within the

following ranges, according to the climatic class

given on the rating plate. The appliance may not

work properly if it is left for a long time at a

temperature outside the specified range.

• Make sure the voltage specified on the rating

plate corresponds to that of your home.

• Do not use single/multi adapters or extension

cords.

• For the water connection, use the pipe supplied

with the new appliance; do not reuse that of the

previous appliance.

• Power cable

modification or

replacement must

only be carried out by qualified personnel or by

After-sales Service.

• It must be possible to disconnect the appliance

from the power supply by unplugging it or by

means of a mains two-pole switch installed

upstream of the socket.

SAFETY

• Do not store explosive substances such as

aerosol cans with a flammable propellant in this

appliance.

• Do not store or use petrol, flammable liquids or

gas in the vicinity of this or other electrical

appliances. The fumes can cause fires or

explosions.

• Do not use mechanical, electric or chemical

means other than those recommended by the

Manufacturer to speed up the defrost process.

• Do not use or place electrical devices inside the

appliance compartments if they are not of the

type expressly authorised by the Manufacturer.

• This appliance is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety.

• To avoid the risk of children becoming trapped

and suffocating, do not allow them to play or

hide inside the appliance.

• Do not swallow the contents (non-toxic) of the

ice packs (in some models).

• Do not eat ice cubes or ice lollies immediately

after

taking them out of the freezer since they

may cause cold burns.

USE

• Before carrying out any maintenance or cleaning

operation, unplug the appliance or disconnect it

from the power supply.

• All appliances equipped with an automatic ice-

maker and water dispenser must be connected

to a water supply that only delivers drinking

water (with mains water pressure of between

0.17 and 0.81 Mpa (1.7 and 8.1 bar)). Automatic

ice-makers and/or water dispensers not directly

connected to the water supply must be filled

with drinking water only.

• Use the refrigerator compartment only for

storing fresh food and the freezer compartment

only for storing frozen food, freezing fresh food

and making ice cubes.

• Do not store glass containers with liquids in the

freezer compartment since they may break.

• Avoid storing unwrapped food in direct contact

with internal surfaces of the refrigerator or

freezer compartments.

• "The bulb used inside the appliance is specifically

designed for domestic appliances and is not

suitable for general room lighting within the

home (EC Regulation 244/2009)".

The Manufacturer declines any liability if the

above advice and precautions are not

respected.

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

Climatic Class Amb. T. (°C) Amb. T. (°F)

SN From 10 to 32 From 50 to 90

N From 16 to 32 From 61 to 90

ST From 16 to 38 From 61 to 100

T From 16 to 43 From 61 to 110

14

HOW TO USE THE FREEZER

Control unit

Adjustable feet

Control unit

33502009GB.fm Page 17 Tuesday, October 27, 2009 12:58 PM

15

The freezer can be used for storing already frozen food

and for freezing fresh food.

Switching on the freezer for the first time

• There is no need to set the freezer temperature on the

thermostat because the appliance is already factory set.

• Plug in the appliance.

• Only place food in the freezer 2 hours after switching on.

Adjusting temperature

From MIN to MAX: make the internal temperature colder.

• Thermostat setting indicator:

MIN - for storing food for short periods;

NORMAL - for storing food for longer periods;

MAX - for storing food for long periods.

Note:

Ambient air temperature, the frequency of door opening and the

position of the appliance can affect the freezer internal

temperature.

Take these factors into consideration when setting the

thermostat knob.

Freezing

Place the amount of fresh food indicated on the rating

plate in the middle compartment. Take care not to place

the food directly in contact with food already frozen.

It is advisable to maintain the thermostat position used

in normal operation.

Important:

When freezing only small amounts of food, the food can be

placed in any compartment, with the exception of the bottom

drawer.

NORMAL

MAX

MIN

Tips for freezing and storing fresh food.

• Before freezing, wrap and seal fresh food in:

aluminium foil, cling film, air and water-tight plastic bags,

polythene containers with lids or freezer containers suitable for

freezing fresh food.

• Food must be fresh and of prime quality.

• Fresh vegetables and fruit should preferably be frozen as soon

as they are picked to maintain the full original nutritional value,

consistency, colour and flavour.

Note:

• Always leave hot food to cool before placing in the freezer.

• Eat fully or partially defrosted foods immediately. Do not

refreeze unless the food is cooked after it has thawed. Once

cooked, the thawed food can be refrozen.

Important:

The table alongside shows the recommended maximum

storage time for frozen fresh foods.

Classification of frozen foods

Put the frozen products into the freezer and classify them.

The storage date should be indicated on the packs, to allow use

within expiry dates.

Advice for storing frozen food

When purchasing frozen food products:

• Ensure that the packaging is not damaged (frozen food in

damaged packaging may have deteriorated). If the package is

swollen or has damp patches, it may not have been stored under

optimal conditions and defrosting may have already begun.

• When shopping, leave frozen food purchases until last and

transport the products in a thermally insulated cool bag.

• Once at home, place the frozen foods immediately in the

freezer.

• If food has defrosted even partially, do not re-freeze it.

Consume within 24 hours.

• Avoid, or reduce temperature variations to the minimum.

Respect the best-before date on the package.

• Always observe the storage guidelines on the frozen food

packages.

MONTHS FOOD

33502009GB.fm Page 18 Tuesday, October 27, 2009 12:58 PM

16

HOW TO DEFROST AND CLEAN THE

FREEZER

Removing the baskets

• Pull the baskets out fully, then lift them up slightly in order to

remove.

Note:

Drawers may be removed in order to obtain increased storage

space.

Ensure that the load does not exceed the limit (if present)

indicated on the side walls of the appliance.

Making ice cubes

• Fill the ice cube tray 2/3 full and place it in the special freezer

compartment.

• Do not use sharp or pointed instruments to detach the tray if it

is stuck to the bottom of the freezer.

• Bend the ice tray slightly to remove the cubes.

Note:

The freezer door will not re-open easily immediately after closing.

Wait a few minutes before opening again in order to allow for

compensation of the vacuum created.

Before any cleaning or maintenance operation, always

unplug the appliance or disconnect it from the power

supply.

Defrost the freezer once or twice a year, or when the

formation of ice on the refrigeration grilles is excessive.

It is perfectly normal for ice to form on the grilles. The

amount of ice which forms and the rate at which it

accumulates will depends on room temperature and

humidity, and on the frequency with which the door is

opened.

If possible, defrost the freezer when it is nearly empty.

• Remove the food from the freezer, wrap in newspaper and

group together in a cool place or in a portable cooler.

• Leave the freezer door open to allow the frost to melt.

• Clean the interior of the freezer with a sponge and warm

water and/or neutral detergent. Do not use abrasive

substances.

• Rinse the interior and dry thoroughly.

• Put the food back into the freezer.

• Close the freezer door.

• Plug in the appliance once again.

• Switch on the freezer.

Fig. 1

33502009GB.fm Page 19 Tuesday, October 27, 2009 12:58 PM

17

CLEANING AND MAINTENANCE

TROUBLESHOOTING GUIDE

1. The appliance is not working.

•Is there a power failure?

•Is the main power switch on?

•Do the household electrical system

protection devices work correctly?

•Is the thermostat setting correct?

•Was the appliance switched on correctly?

2. Excessive frost build-up.

•Has the defrost water drain been positioned

correctly?

•Is the door shut properly?

Attention:

• The front edge of the appliance may be hot.

This prevents the formation of condensation

and is not a defect.

• Gurgling and hissing noises due to

expansion in the refrigerant circuit are

normal.

AFTER-SALES SERVICE

Before contacting the After-Sales Service:

1. See if you can solve the problem yourself (see

“Troubleshooting guide”).

2. Switch the appliance off and then on again to

see if the problem has been solved. If it has not,

switch off the appliance again and repeat the

operation after one hour.

3. If the problem persists after this course of

action, contact After-sales Service.

Specify:

•the nature of the fault,

•the model,

•The Service number (the number after the

word SERVICE on the rating plate inside the

appliance),

•Your full address,

•Your telephone number and area code.

Note:

The direction of door opening can be changed.

If this operation is performed by After-sales

Service it is not covered by the warranty.

The door cannot be reversed on models with

front handle.

Periodically clean the condenser at the rear of the appliance

with a vacuum cleaner or brush.

Prolonged disuse

• Empty the freezer.

• Disconnect the freezer from the mains power supply.

• Defrost and clean.

• Leave the door open to prevent formation of

unpleasant odours and to eliminate any dampness.

33502009GB.fm Page 20 Tuesday, October 27, 2009 12:58 PM

18

INSTALLATION

• Install the appliance away from heat sources. Installation in a

hot environment, direct exposure to the sun or installation

near heat sources (heaters, radiators, cookers) will increase

power consumption and should therefore be avoided.

• If this is not possible, the following minimum distances must

be respected:

•30 cm from coal or paraffin stoves;

•3 cm from electric and/or gas stoves.

• To optimize appliance efficiency, leave a 5 cm gap above the

appliance and make sure that adjacent kitchen units are

sufficiently distanced to allow air circulation.

• Install the appliance in a dry, well-ventilated place, and ensure

it is level, using the front adjustment feet if necessary.

• Clean the interior.

• Fit the accessories.

Electrical connection

• Electrical connections must be made in accordance

with local regulations.

• Voltage and power consumption are indicated on the rating

plate inside the appliance.

• Regulations require that the appliance be

earthed.

The manufacturer declines all liability for injury to

persons or animals and for damage to property

resulting from failure to observe the above procedures

and reminders.

• If the plug and socket are not of the same type, have the

socket replaced by a qualified electrician.

• Do not use extension leads or adapters.

Disconnecting the appliance

It must be possible to disconnect the appliance by unplugging it

or by means of a two-pole switch fitted upline of the socket.

33502009GB.fm Page 21 Tuesday, October 27, 2009 12:58 PM

19

DOOR REVERSIBILITY

The direction of door opening of your freezer can be

changed.

• Make sure that the freezer is not connected to the power

supply and that it is empty.

• Reversing the direction of door opening is a task which

requires two people.

Tools required

• Phillips style screwdriver

• Flat bladed screwdriver

• 8 mm and 10 mm socket or spanner.

Lay the fridge/freezer on its back in order to gain access to the

base, being careful not to tip it back by more than 45º. Rest it

on the soft foam packaging or similar material to avoid

damaging the cooling pipes at the rear of the appliance.

Remove the two screws on the rear of the fridge/freezer.

Lift the top off the fridge/freezer.

Use the 8 mm socket or spanner to remove the 2 hinge bolts.

Remove the 2 bolts from the opposite side.

Remove the bracket and plastic surround.

Remove and replace the pin in the bracket.

Refit on the opposite side of the fridge/freezer cabinet.

Remove the blanking plug from the new hinge side and refit it

on the opposite side.

33502009GB.fm Page 22 Tuesday, October 27, 2009 12:58 PM

20

Remove the levelling feet by unscrewing.

Remove the bottom bracket using an 8 mm socket or spanner.

Remove and replace the pin, using a 10 mm socket to unscrew the

nut and a flat bladed screwdriver to remove the pin. You may

need to push the pin through from the underside to remove fully.

Remove the screw on the base and refit it on the other side.

Remove the blanking plates from the unused side of the fridge/

freezer and refit them in the holes left by the brackets.

Replace the door and brackets in reverse order.

When replacing the feet take care to ensure the larger foot is on

the side without the bracket.

Check the door is aligned horizontally and vertically and that the

seal fits properly all around before tightening the bottom hinge.

Note:

The direction of door opening can be changed. If this

operation is performed by After-sales Service it is not

covered by the warranty.

33502009GB.fm Page 23 Tuesday, October 27, 2009 12:58 PM

21

ELECTRICAL CONNECTION

1) For Great Britain only

Warning - this appliance must be earthed

Fuse replacement

If the mains lead of this appliance is fitted with a BS 1363A

13amp fused plug, to change a fuse in this type of plug use an

A.S.T.A. approved fuse to BS 1362 type and proceed as follows:

1.Remove the fuse cover (A) and fuse (B).

2.Fit replacement 13A fuse into fuse cover.

3.Refit both into plug.

Important:

The fuse cover must be refitted when changing a fuse and if the

fuse cover is lost the plug must not be used until a correct

replacement is fitted.

Correct replacement are identified by the colour insert or the

colour embossed in words on the base of the plug.

Replacement fuse covers are available from your local electrical

store.

2) For the Republic of Ireland only

The information given in respect of Great Britain will frequently

apply, but a third type of plug and socket is also used, the

2-pin, side earth type.

3) Socket outlet / plug (valid for both countries)

If the fitted plug is not suitable for your socket outlet, please

contact Whirlpool Service for further instruction. Please do not

attempt to change plug yourself. This procedure needs to be

carried out by a qualified Whirlpool technician in compliance

with the manufactures instructions and current standard safety

regulations.

33502009GB.fm Page 24 Tuesday, October 27, 2009 12:58 PM

22

Page is loading ...

Hotpoint WM1510W Owner's manual

Hotpoint WM1510W Owner's manual

in other languages

Related papers

Other documents