Insignia NS-LT500P-1 Quick setup guide

Brand: Insignia

Model: NS-LT500P-1

Type: Quick setup guide

This manual is also suitable for

NS-LT500P-1 Refrigerator Filter

The Insignia NS-LT500P-1 refrigerator filter is designed to reduce chlorine, taste, and odor from your drinking water, providing you with clean and refreshing water straight from your fridge. It effectively removes impurities, ensuring that your water is safe to drink and tastes great. To maintain its effectiveness, the filter should be replaced every three to six months. Installation is simple: soak the new filter for 15 minutes, remove the old filter, insert the new one, and run about two to three gallons of water through the dispenser to remove air and carbon pieces.

GENERAL INSTALLATION GUIDELINES

• It is normal for black carbon nes (particles) to appear on the outside of

your lter. This happens when the lter is jarred in shipping. It is safe,

simply wipe it o.

• Connections on our lters are larger in size to prevent leakage. This

might require more hand leverage to install.

INSTALLING THE WATER FILTER

Carefully remove the plastic cap from the new lter before installation.

1 YOU MUST SOAK your new lter in water for 15 minutes prior to

installing it in your refrigerator to remove air from the carbon block.

2 Twist the old lter a quarter-turn counter-clockwise.

3 Pull the lter straight down and discard.

4 Push the new lter up into the refrigerator until it stops.

5 Twist the lter a quarter-turn clockwise.

6 Run about two to three gallons of water through your refrigerator’s water

dispenser to remove air and loose carbon pieces. The water may be

cloudy and sputter until the air is removed.

7 Reset your “change lter” indicator (if your refrigerator has one). See

below.

RESETTING YOUR CHANGE FILTER INDICATOR

Note: These are the most common lter reset instructions. If the instructions don’t

work for your refrigerator brand, see the documentation that came with your

refrigerator.

Before using your new product, please read these instructions to prevent any damage.

PACKAGE CONTENTS

• Refrigerator lter(s) (1 pack)

• Quick Setup Guide

REFRIGERATOR BRAND

INSTRUCTIONS

Press and hold the reset button for three seconds.

QUICK SETUP GUIDE

Refrigerator Filter

NS-LT500P-1

TROUBLESHOOTING STORAGE AND MAINTENANCE

• Replace your lter every three to six months to prevent bacteria and

fungus growth in your lter, supply lines, and storage tank.

• Stored lters do not expire. Keep your unused lters in a cool, dark, and

dry place until you need them.

• If you do not use your water dispenser for more than four days, run two

gallons of water before using it to prevent bad tasting water.

ONE-YEAR LIMITED WARRANTY

For complete warranty, visit www.insigniaproducts.com.

CONTACT INSIGNIA

1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)

www.insigniaproducts.com

CERTIFICATIONS:

INSIGNIA is a trademark of Best Buy and its aliated companies.

Distributed by Best Buy Purchasing, LLC

7601 Penn Ave South, RichWeld, MN 55423 U.S.A.

Made in China

V2 ENGLISH 18-0534

PROBLEM

My refrigerator is not

dispensing water

My water dispenser is

dripping

My water is cloudy or

contains black carbon

pieces

My new lter is making

noises or sputtering

My water tastes bad

SOLUTION

• Make sure that you soaked your lter in water

for 15 minutes before installing.

• Make sure that the lter is securely connected

to the receiver. Do not use tools to tighten the

lter in place.

• Make sure that the water line to the refrigerator

is turned on. The valve must be completely

open for the refrigerator to receive water.

• Make sure that the refrigerator door is closed or

the dispenser will not work.

• A few drops are normal. If the water is dripping

constantly, have a service technician check your

refrigerator’s water valve.

• Cloudy water is caused by microscopic air

bubbles. Run two to three gallons of water from

your dispenser to clear the air bubbles out.

• Black carbon pieces in the water are normal and

appear with all carbon lters. Run two to three

gallons of water through your dispenser to

remove loose carbon pieces.

• Make sure that you soaked your lter in water

for 15 minutes before installing.

• Noises and sputtering are caused by trapped air

pockets. Run two to three gallons of water from

your dispenser to push the air out.

• If you do not use your water dispenser for more

than four days, run two gallons of water

through the dispenser before using it.

• Make sure that you replace your lter every

three to six months to prevent bacteria growth.

Tested and Certied by NSF International in Model

EFF-6005S against NSF/ANSI Standard 42 for the

reduction of chlorine, taste and odor.

REPLACEMENT

ELEMENT

Insignia NS-LT500P-1 Quick setup guide

Brand: Insignia

Model: NS-LT500P-1

Type: Quick setup guide

This manual is also suitable for

NS-LT500P-1 Refrigerator Filter

Download PDF

report

Insignia NS-LT500P-1 Quick setup guide

This manual is also suitable for

Insignia NS-LT500P-1 Quick setup guide

Related papers

Other documents