Haier HWR06XC3 Owner's manual

Page is loading ...

Thank You Forbuying a dependable, energy saving and easy to operate

HAJERroom air conditioner This manuaJcontains useful information for

you to maintain, operate, install and safely useyour room air condifianer_

Your air conditioner deans, coals and dehumidifies the air in your room to

provide you with the ultimate bvel of comfort.

Pleaseread instructions carefully before using the producL Also, do not

forget to fiHout and mail the Product Registration Card.

Record Your ModeUand SeHaUNumber°

For all your service calls during the warranty period the bHowing

information will be needed. Affach the sales receipt to this guide and keep

for future reference. This information can be obtained from the serial pJate,

which is on your air conditioner: This is either on the cabinet (side or back)

or you may have to remove the front grille to Jocateit.

1) Air conditioner mustbe connectedto proper electrical outlet with the

correct electrical supply. (seetabJe)

_. 2) Proper grounding mustbe ensuredto reducethe risk of shockand fire.

DO NOT CUTOR REMOVETHEGROUNDING PRONG. If you do

not have a three-prong electricreceptacleoutlet in thewall, have a certified

electrician install the proper receptacle. Thewall receptacleMUSTbe

properly grounded.

3) Do not use if power cord isfrayed or otherwise damaged. Also avoid

using it ifthere are cracks or abrasion damage along the length, plug or

connector.

4) DO NOT USEAN ADAPTEROR AN EXTENSIONCORD.

5) When installing your air conditioner in a window, make surethewindow

is strong enough to hold the weight of the air conditioner. Youalso want to

secureand correctly install your air conditioner properly to prevent it from

falling. Extra bracketsand or support may be required depending

on your window.

6) Do not block airflow inside or outside the air conditioner with blinds,

drapes, protective covers,shrubs or bushes.

7) Becareful of sharp edgeson thefront and rear fins of the unit that could

cut and cause seriousinjury.

8) Becareful when lifting the air conditioner to install or remove the unit.

Always usetwo or more people for this.

9) Always unplug theair conditioner before servicing it or moving it.

PAGE

A Word From Haler 1

P_duct Registration 1

Safely/Precautions 2

Warnings 4

ElectricaJSafely/ 4

Tips 5

Energy Saving Guide 5

FeQtures 6- 7

@peratlng Gulde 8-13

Normal Operating Sounds 8

Operating instructions 8-13

JnstaJJatians 14-18

Parts 15

Tools 1g

Installing Unit into A Window 1(3-18

Clean and Care Guide 19-20

TroubUeshaoting 20- 21

Warran_ Jnfarmatian 22

3

Following the safety messagesis very important.

Thesemessagescan save you from being iniured or killed.

Warning symbols alert you to be carefd and meansDanger. Always

follow instructions to be safe and reduce chancesof iniury or death.

Warning and Danger signswill precede safety messages.

Grounding: This room air conditioner must be grounded.

Grounding reduces the risk of enectricshock by

providing an escape wire for the eJectriccurrent,

The power cord has a grounding wire with a

grounding pJug PJugit into an outJetthat is

propernyinstaJJedand grounded.

WARNHNG: Improperuseof the grounding

pJugcan resuJtin a risk of dectric shock.

CaJJa qualified eJectricianif you don't understand

the grounding instructions or if you are not

sureif theair conditioner is properly grounded.

ifthe waJJdectrid outJetis not grounded, please contact an

eJectridan to have it repJacedwith a properly

grounded outJet.

DO nOtr Under Qny ¢_rcu_$t_n¢esr CUt or re_ove t_e

thlrd (gr@und) prong from the power cord.

Adapter PUug: We strongly advise against using an adapter plug,

4

o This Air Conditioner isdesigned for use in a douUe hung window.

Whine installing unit be sureto flit air conditioner _/4 inch oubvard to

havethe water drip outside the house,

s_k '_mnstalJthe unit on the north side as normally that is the shaded side. This

will enhance the operation of your unit.

Window has to be strong for installation. Extra brackets and or support

may be required depending on your window.

Measure the window before installing, if the window is too big for the

unit you may require professional installation,

s_k _ Usecorrect eJectricvoltage and proper ampere for the unit to run

effectively

_ Only Jeta certified eJectrician do any modifications to your eJectrical

outJet,

When installing your air conditioner make sure to seal aHareas where

there is a possibiJih/of air Jeakage.

Airflow should not be bbcked inside either by curtains, drapes or

furniture or outside by shrubs or bushes

Do not needJessJyuse an dectricd Jightor other appliances that

produce heat

Keep the ventdosed on the air conditioner when in the cooling function,

Keep the blinds and the drapes drawn on aJlthe other windows.

o While cooking usean exhaust fan in the kitchen to remove the excess

heat produced.

Always usethe correct BTUsize air conditioner to cool the room to

attain optimum efficiency.

5

iii[iiiiiiiii

iiiiiiiiiiiii

/

easy access

filters

electro_ic

touch pad

Electronic touch pad

TEMP/T[MER

displa}

Signal receiving j

window

COOL

button --

FAN

button

TIMER

button

ENERGY SAVER

btdton

@

@ ÷ @ .--

low m_

@r_a_ _n sp_d

€,

L TEMPorTIMER

button

-- POWERON/OFF

button

@

high

f_n a_d

6

t oThermostat

This amlowsyou to adiust the temperature of the air

The lower the setting the cooler the air temperature

w_th this you can set the temperature to your

desired comfort level You can set_e temperature

between 61 _F and 86" F

2. fall Speed

You hove 3 lards of Fen Speed to set e_your

d_fr_d comfort level. HIGH, MED and LOW.

In COOL mode: press COOL buffon, for each

press, COOL speed will changes as f_llows:

@

@ @

@ ÷ @ ÷ @

lowcod & low r_edceoU&mad f_ns_ed

highcool&high

_n sp_ fanspeed

In FAN mode: press FAN button, br each press,

FAN speed will changes as follows:

@

@ @

@ _ @ -'* @

l¢_v mad high

_n _p_ _n _peed _n _pe_

,3. Fund'ion.

Your air conditioner has 2 Functions

a) COOL

Here the air conditioner will operate the compressor

and the desired fan speed setto give you chilled

cold air for your comfort

b} Fen

You can run the fan only on not so hot days. The

fen con be setto run at 3 speeds (HUGH fan,

MED fan end LOW fen ) as desired by you

4, Energy Saver

When turned "ON" the fan will shut off 3 minutes

after the compressor cycle off This will not onJy

save you electrical and energy costs but aRsoshuts

off the unnecessary noise of the fan motor running

In the "OFF" position the fen will not shut off when

the compressor cycles off The fan wilJ keep running

at the set level

5. Ti_er

Your air conditioner con be set to go on or off at

your desire This can be done up to 24 hours in

advance

6, 2 Wc_y Air FJ_w

These air directional louvers let you control the

direction of the airflow in your required direction

The airflow can be directed right side - left side

7. Window mnstaJ| Kit

Enables you to install the air conditioner in a

double hung window Extra brackets or support

may be needed depending on your window

8_ Re_@te ¢@n_ro|

This full functional wireless remote allows you to

operate your air conditioner from a distance You

need not have to get up to change the settings, the

functions or to turn the unit on or off

ll@r l @!e " tlHg 5@ Hds

The folowing sounds are normally heard during the operation of an air conditioner.

®Cool airflow movementas didated by the set fan spee&

Water sounds. This is normal as your air conditioner acts as a

dehumidifier aJso.Thusyou wil hear water sounds from water drops

faling on the condenser

oAs the refrigerant tows through the inner seaJedtubing a rushing noise

may be heard.

Raffling or vibrating noises may be heard due to poor wal

or window instalafion.

High pitch compressor sound may be heard.

@pe ethsg Ins tru¢lieHs

Folowing are the operating instructionsof your electronic air conditioner.

After instaling your air conditioner pJug it in to the proper dedricaJ outJet

in the wal Keepthe vent in the closed position. Now set the air

conditioner at your comfort bye[ This ful functional wireJessremote alows

you to operate your air conditioner without having to get up and go to the

unit. The ful function feature alows you to change the settings and turn the

unit on or off from the remote itseJf.This controJpad works the same as

the control pad on the air conditioner.

(See Fig # ])

Fig. # 1

Remote ¢@ntr@J

After you pJugin the unit it will perbrm a senttest. All the display Jights

will turn on for 3 seconds The LEDdisplay will read "88". If any dispnay

Jight fails to turn on you may need service on the unit. After the 3 seconds

seJftest the unit winJautomatically go to the stand by mode. Now aUJJights

will be off and you wiJnhave to turn "ON" by pressing the On/Off key

After pressing "On/Oft/', the unit starts to work and enters the statusof

"Fan OnJy" with low setting.

You wiJnhave to pressthe (,_)or (_) key on the TempiTime to set the

temperature at your desired comfort. You can choose between

61°F and 86°F. Once the temperature is setyou can raise or Jowerit

by pressing the (,_)or (T)keys (Only when the unit is cooJing,

can the temperature setting be adjusted.) (See Fig. # 2)

Fig. # 2

¢ontroU PameU.

ff you want to cool the room press the COOL function. If you just need

to use the fan onJy, press the Fan function. (See Fig.# 3)

Fig.#3

¢on_roJ Panel

Once the function mode is decided you wdl hove to set the fan speed. If

you choose the COOL mode you con run the Fan in one of fhe 3 speeds

HmGH,MED and LOW. (See Fig. # 4)

Fig, # 4

¢ontroj Panel _

low cod & low

fan speed

@

reed cool & rned

fan speed

10

For cool days you may want to run the " Fan Only " funcfion_ Here the fan

can runsat HGH, MED or LOW. (See Fig. #5 )

Fig. # 5

Control Panel

@

@ @

low rned high

Timeron or Timeroff mode is used to pre_startor shutoff your unit in

advance.You can program this up to 24 hoursin advance. Youcan use

the Timerin 2 functions ke Cod or FanOnly.

_TimerOn. (SeeFig. # 6)

Unit mustbe on to setthe timer: Unit wiUJshutdown automaticdJy after it

acceptsthe settingsin 5 seconds.Usethismode to presserthe starttime of

the unit 24 hours inadvance.

a) PressOn, LEDdlsplay wiJUshow"XX" (timesetUasttime)when power

is connectedfirst time, LEDdispJaywilJshow "01" .

b) Setdesired numberof hours by pressingthe (A) pad of theTemp/Time

buttons,one for each houn If you passedthe desired time usethe(_r)pad

key to lower the seJection.

c} After set Timer On, LED display will show the time° This time

displayed: unit will starts after X hours.

11

Fig. # 6

¢ontro_

_TimerOff (See Fig.# 6}

Unit mustbe running to setthe timer off. Usethis to presetthe time you

would like the unit to shutoff

a) PressOff, LEDdisplay wiHIshow "XX" (time setlost time)when power

is connectedfirst time, LEDdispJaywiHIshow "01" .

b) Setdesired number by pressingthe (A)pad oFtheTemp!Timebuttons

One Foreach hour. mfyou passedthe desiredtime, usethe(_) pad keyto

lower the seJecflon.

c) After set Timer Off, LED dispHaywiHHshow the room temperature

about 5 seconds Ha_er_

When using the timer the unit wiHI use!revert to the last Cod and fan

settings when activated. The timer must be reset every time you choose to

use it.

P_ne_

T[M[ERON -=_ TIMEROFF -=_ CANCELLED

Re_o_e Con_rom:

a) Pressing the TIMERON buffon one time, the seffing of TIMER ON can be done.

Pressingthe buffon for e second time, the seffing is cancdHed.

b) Pressing the TIMEROFF buffon one time, the seffing of TIMER OFF can be done.

Pressingthe burton for e second time, the se_ing is cancelled.

E|ectrgnlc _ogch pad

PressTIMERbunion, for each press, THMERmode will changes as foHIows:

T[M[ERON -=_ T[M[ER()FF -=_ (ANCELLED

t ]

12

EnergySaver: By pressing this keyyou will activate the unit to go in the

energy saver mode. The fan will be off 3 minutes after the compressor

cycle off By deactivating it the fan keepsrunning at the set speedeven if

the compressor shutsoff. (SeeFig # 7) (Thisfunction isavaiJabJein the

coding function only)

Fig. # 7

¢ontroJ PaneJ

i

When unit is in "Energy Saver" mode theLEDdisplay wiJl show

room temperature, Pressthe (A), (_) keyto get settemperature.

13

Beforeyou install your air conditioner check the fdbwing:

1) The unit is free of aHobstructions inside and outside the room e.g. drapes,

curtains, furniture, plants, shrubs, bushes,trees, other structures like building,

garage etc. Air conditioner must have dear unobstructed airflow through the

condenser to removethe heat

2) Thewindow is strong enough to hold the weight of the air condifionen

Extra brackets or supports may be needed depending on your windows

3) Thewindow siJland track are strong enough to hoJdthe weight of the

air conditioner.

4) ThewdJ is strong enough to hdd the unit Extra brackets or supports may be

needed depending on the wall

5) There is adequate and proper power suppJy near the air conditioner.

_j_6) DO NOT use adapter pJugs.

_j_7) DO NOT use extensioncords_

_.8) DO NOT cut or remove the ground prong.

_j_ 9) DO NOT modify the pJug or the eJectricd wdJ outbt in any way_

mfpJugdoes not fit the dectricd outJethave a certified eJectriciando the

necessarychange.

_10) DO NOT connect eJectricd power to the unit before installation

_11 ) DO NOT use if power cord is worn out, frayed or otherwise damaged.

Avoid using if there are cracks or abrasion damage dang the bngth,

pJugor connection.

14

Parts SuppUied

short scre_s 13/32"

basepan angle

wood sclews 31/32"

r,_

top rail

window sea[ gasket

"CR2025" bat ery lef_ and right

"_'_z_. Remote side curt....

control

You will need to have the following rods to hdp you in the installation of

your air conditioner_

_Sdssors

•PhiHipsScrewdriver

_Standard Screwdriver

®Pliers

_Wrench

oDrill and Drill Bits

•TapeMeasure

oGIoves

®Level

_Sockets

15

nstdJing Unit intoA Window

Window Opening Requirements

Theair conditioner is designedto fit into double or single hung sashtypewindows Eachof the

units comeswith an installation kit that provides adjustabb mounting louvers, to filUthe gaps

between the sidesof theunit, and the window Frame,Thechart below reflectsthe dimensions

of theunitswith, and without installationkits. Measureyourwindow opening width and compare

itto thechartbebw to ensurethatit meetsthe minimumand maximumwindowwidth requirements.

Afinch)

B(inch)

C(inch}

Dfinch)Max

D(inch)Min

CaseHigh

Casewidth

CaseDepth

1"4 D _1

HWR05XC3,HWROGXC,3

ASSEMBLE

CURTAINS/TOPRAIL

16

PREPARE

WINDOW FOR

iNSTALLATiON

I This Imi_ is design_ d _r inslal[alkm ill slandaM double hun_._ x_indo_a

_h actual opening _dt[ls of 22" Io 30" • The upper and lower sash

m_ls[ opell stll_cien_[y [(i allow a (?[ea_ _!rl]c_t] (ip_ll[n 2 (if 1'4.1from [lie

bofl(ll_l of [lie s_t_[l kl IlK! w]nd(iw sRio]

2 If slorm window presents i_l_erlemnce, _s_en a 2" wide wood strill01ol

i_lcluded) (()lITER SIK) _o lhe inner _ndow sill across I[le l_l[l wklfil of

file sill¸ The wood s_rip shoukt be Ihick enot@l _o raise file hei2[ll of

lhe window _,ill_,(i IhaI file unil can be insiaHed _Ihou_ i!lle_!r_mce by

(()L3T])()()RS) I(_help condensalion _(_dlain properly l(_ I[le outskle

3 hlslall a second wood s_rip (a[l_lr(_xiI_la_e[y 6" lon 2 by 3/2" _de and

same fl_ickness as firs_ s_rip) ill Ihe cen_er of I[le ot_lel ¸sill flush againsl

file back oil file inner sill¸ This will raise basepan allgle •

4 If Ihe distance I/e_en STORM WINDOW H_AME and WO()D ST_P

M()_JNTED ON TOP OF INNER SILLis more fllan 1" . _o of wood

s[rip ar_ i1o[ necessary

INNER

SIIt

WORK) STRIP

o

u

T

D

O

R

S

P'MAX

S S

LOCATINGUNIT IN

WINDOW

()jKn ilk willdo_ alld mtFk c_ ll{er lill( Oll {h(

(:_!nK!r (if I]le ii111(!1' si[]

INNER%ILL

ATTACHBASEPAN

ANGLE

lnsiMl file basep m angle behind file ironer x_indow sill. _dfll

file shor_ side of basepan angle as s[lown Use file 2 shorl

screwsl 3/32" prodded

The basepan aligle helps _o hold unit securely in place¸

l_e sure l(_ place basepan angle edge flush agains_ back

of inner sill¸

INNERSILl_

S[tORT SCREVvq 3/32'

CENTER LINE

[NS[DI

SHORT SI])E

()UTS[I)II

BASEPANANGLE

17

_5 INSTALLTHEAIRCONDITIONER

IN THEWINDOW

Carefully lill file air / ondi{ionei uld slide i{ il_lo the opell

window¸ M_tk_ 5tlr_ IJl(!bo_lom _llide (if _he ai_ c(lildi_ioller

drops [I1{(¸1I]1_ _(llches of Ih_ b_tsel)a_l a11_[e

While s_ea@ing _he air clmditioner carehllly bring _he

_ndow sash down be[lind the upper guide of Ihe air

condil_onel

ABOUT l,'M _'

INSTALLTHESEALCASKET

ANDSASHLOCK

Exlend the sid{ curlai_ls I(} fill die

31/32 _'_o secure Ihem

Cu_ _he seal gaskel Io Ihe wi_ldow

mdlh SItiff die sash seal belween the

glass a_d lhe window Io p_ew_n_ air

all(] [IIS_CIS[Iota _{_!llill_]II[(i [he _l_ll

Fallen Ihe basepan angle, using a

shorl screw 13/32",

BASEPAN :\N(;LI!

S| [()RT SCRE\_ 13/32"

_INI)()W SEAl_(;ASKET

18

TABAIRFILTER

] r

@

Always unplug your air conditioner befk)re cleaning,

Air filter needs to be cleaned at least once a mouth fi.)r your

unit to operate at optimum efficiency. The filter can be slid out from

the side by pulling on the tab located on the middle left side of the lmnl mask.

The filter may be washed or vacuumed. Remove the excess water [rom

the fiJter by gentJy shaking the fiJter.This wiJ[ remove dust and particles

trapped in the filter. After cleaning, reinstall the filter.

DO NOT use yore" air conditioner without the air filter in place.

To clean the fl'ont panels or the cabinet DO NOT use harsh

chemicals, abrasives, ammonia, chlorine, bleach, concentrated

detergents, solvents or metal scouring pads.

Someo[ thesechemicals may dissolve, damage and!or discolor your

air conditioner.

Always use a soft cloth dampened with water or mild soap

and water solution to wipe the fl'ont if the cabinet.

Wipe dry with a softcloth.

19

Tostore your air conditioner, after the season, remove the unit from the

window as per the instdJation guide. Repack the unit in its original box

and store away. if your unit is instdJed in a wahlor you do not intend to

remove it from the window then cover the outside with a winter cover,

This can be purchased from the retaiJerwhere you purchased your

air conditioner or from your JocaJhardware store.

Before putting away your unit make sure any water Jeffin the pan is

removed and drained away. Water Heftin the pan couHdHeadto Rusting

or damage to the dectricd connections.

Hfa_r conditioner does not operate:

Check if unit is pJuggedin. The pHugmay have come Hoose.

Check if the unit is in "Off" mode.

Air fro_ air conditioner is warm:

TheA/C setting may need to be raised

Joe formation @n co@UingcolJs:

o Outside temperature too coJd.Set the unit on fan only

setting to defrost ice.

bwer temperature setting. Temperature setting may be too cold.

Unit BTUmay be too high for the room.

20

Page is loading ...

Haier HWR06XC3 Owner's manual

This manual is also suitable for

Haier HWR06XC3 Owner's manual

in other languages

Related papers

Other documents