Ancona VECTIM365 User manual

Page is loading ...

ENGLISH

Installation Manual

3

Table of Contents

Page

Special Warnings ..............................................................

Product Dimensions and Cutout Requirements.............

Important Preparation Suggestions .....................................

Cooktop Installation..........................................................

Electrical Connections....................................................

General information...........................................................

3-Wire branch circuit ......................................................... 1

4-Wire branch circuit ......................................................... 1

Pay attention to these symbols present in this

manual

DANGER

You can be killed or seriously injured if you don't

IMMEDIATELY follow instructions.

WARNING

 This is the safety alert symbol. This symbol

alerts you to potential hazards that can kill or

hurt you and others.

 You can be killed or seriously injured if you

don't follow these instructions.

READ AND SAVE THESE INSTRUCTIONS.

To installer:

Leave these instructions with the appliance.

To customer:

Retain these instructions for future reference.

WARNING

 If the information in this manual is not followed

exactly, a fire or explosion may result in

personal injury or death.

 Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of

this or any other appliance.

WARNING

Special Warnings

Please read all instructions before using this appliance

Proper installation is your responsibility. Have a

qualified technician install this cooktop.

Important:

 Observe all governing codes and ordinances.

 Write down the model and serial numbers before

installing the cook top. Both numbers are on the

serial rating plate located on bottom of cooktop

box.

Before Starting Installation

WARNING

It is the customer's responsibility to contact a

qualified electrical installer. To assure that the

electrical installation is Adequate and in

conformity with national electrical code:

ANSI/NFPA 70-latest edition** or CSA standards

C22.1-94, Canadian Electrical Code, part No.0-

M91 - latest edition*** and all local codes and

ordinances.

Copies of the standards listed may be obtained from:

** National Fire Protection Association One Batterymarch Park

Quincy, Massachusetts 02269

*** CSA International 8501 East Pleasant Valley Rd. Cleveland,

OH 44131-5575

To eliminate the risk of burns by reaching over

heated surface units, cabinet storage space located

above the surface units should be avoided. If he

cabinet storage is to be provided, the risk can be

reduced by installing a range hood that projects

horizontally a minimum of 5" (12,7 cm) beyond the

bottom of cabinet.

IMPORTANT: Save these instructions for the local electrical inspector use.

INSTALLER: Please leave this manual with owner for future reference.

OWNER: Please keep this manual for future reference.

ENGLISH

Installation Manual

4

�



Figure �.

LENGTH OFF CUT

A

LENGTH OFF CUT

B

1-1/2” (3.8CM)

MIN CLEARANCE

SEE NOTE

R

FROM EDGE OF CUTOUT

AND FRONT EDGE OF

COUNTERTOP

2-1/2” (6.5 cm)

SLOT FOR

CABLE

ROUTING

3-1/2” (9 cm)

2-1/2” (6.5 cm)

1-1/4” (3,2 cm) Canadian

CUTOUT DIMENSION

2-1/4” (5,7cm) US

21” 3/16 (53,8cm)

30” 3/8 (77,1cm)

2” 7/8 (7,4)

1/4” (0,6cm)

3” 1/8 (8cm)

1” (2,5cm)

1/4” (0,6cm)

2” 7/8 (7,4)

36” 3/16 (91,9cm)

21” 3/16 (53,8cm)

3”1/8 (8cm)

1” (2,5cm)

Figure 1.

30’’

36’’

ENGLISH

Installation Manual

5

Important Preparation Suggestions

1. Chamfer all exposed edges of decorative laminate

to prevent damage from chipping.

2. Radius corners of cutout and file to Insure

smooth edges and prevent corner cracking.

Recommend 1/4“or 3/8“diameter drill In each

corner.

3. Rough edges, inside corners which have not been

rounded and forced fits can contribute to cracking

of the countertop laminate.

This cooktop has been designed with wide

tolerances of cut-out to cover possible

replacement with other brands. We recommend to

that you consider the minimum dimension of cut-

out size In the case of new Installation.

Some cut out sizes for possible replacements:

Figure 3. Cutout dimensions and requirements

D

G

C

E

F

CUTOUT REQUIREMENTS

WALL COVERING CABINETS,

AND COUNTERTOP MUST

WITHSTAND HEAT UP TO 93° C (200° F)

CUTOUT

WIDTH

A B C D E F G

30”

(76.2cm)

28-11/16”

(72.9 cm)

28- 15/16”

(73.5 cm)

19-1/4”

(49.0 cm)

19-5/8”

(49.8 cm)

30”

(76.2 cm) min

18” (45.7 cm)

min

Height from

countertop

to nearest

cabinet on

either side of

unit

30” (76.2 cm)

min.

(see note*)

Clearance

from

countertop to

unprotected

overhead

surface

2” (5 cm) min

Clearance

from cutout to

side wall on

the left and

right of the

unit

13” (33 cm)

Depth of

unprotected

overhead

cabinets

36”

(91.4cm)

34-1/16”

(86.5 cm)

34- 5/16”

(87.2 cm)

19-1/4”

(49.0 cm)

19-5/8”

(49.8 cm)

36”

(91.4 cm) min

IMPORTANT

Under the cooktop it is necessary to install a partition,

as shown in gure 2-3.

* NOTE

24” (61 cm) min. clearance if bottom of wood or metal cabinets is

protected by not less than 1/4“ (0.6 cm) ame retardant millboard

covered with no less than No. 28 MSG sheet steel 0.015” (0.04 cm)

stainless steel, or 0.024” (0.06 cm) aluminum or 0.020” (0.05cm)

copper. 30”(76.2 cm) min. clearance between top of cooking platform

and bottom of unprotected wood or metal cabinet

Dim. Inches cm

• 30” 28-15/16” x 19-5/8” 73,5 x 49,8

• 36” 34-5/16” x 19-5/8” 87,2 x 49,8

ENGLISH

Installation Manual

6

Cooktop Installation

WARNING

 Excessive Weight Hazard

Use two or more people to move and install

cooktop.

Failure to do so can result in back or other injury.

 Cut Hazard

Beware of sharp edges. Use the polystyrene ends

when carrying the product. Failure to use caution

could result in minor injury or cuts.

 Always consult the countertop manufacturer for

specific instructions.

 Ensure the countertop is square and level and

ensure no structural members interfere with space

requirements.

 Prepare the cut-out according to the instructions

(see cut-out dimensions).

 Make sure the wall coverings, countertop and

cabinets around the cooktop can withstand heat

(up to 200 °F / 93 °C).

Figure 4. Tools you will need

Step 1

Remove packaging materials and literature package

from the cooktop before beginning installation.

Remove Installation Manual from literature pack and

read them carefully before you begin.

Figure 5. Parts

Step 2

Place a towel or table cloth onto the counter top. Lay

the cooktop upside down onto the protected surface.

COOKTOP

CARDBOARD

TOP-CARDBOARD

MANUAL

TOP PACKAGING

GASKET

SCRAPER

BOTTOM PACKAGING

BURNER BOX

TABLE CLOTH

Figure 6.

ENGLISH

Installation Manual

7

Step 3

A foam tape is provided to seal the cooktop edges to the

countertop. Apply tape approximately 1/16” (1.5 mm)

from the glass edge to the underside of the cooktop

glass. Use tape around the entire glass perimeter. Cut

off excess where tape ends butt.

Remove the two screws from burner box, then place

the bafe as showed below xing it by the screws

removed previously.

BURNER BOX

COOKTOP GLASS

FOAM TAPE

SEAL

Figure 7.

SCREWS

BAFFLE

Figure 7b.

Step 4

Insert the cooktop centered into the cutout opening.

Make sure the front edge of the counter top is parallel

to the cooktop. Make nal check that all required

clearances are met.

Figure 8.

Step 5

Four clamp brackets are provided to clamp the cooktop

to the countertop. Tighten screws just enough to hold

brackets in place when cooktop is put into cutout.

Tighten screws securely.

Figure 9.

ENGLISH

Installation Manual

8

Figure 1.

Figure 1.

WARNING

THE CONDUIT IS 3 FEET LONG

The junction box, must be located where it will

allow considerable slack in the conduit for

serviceability.

Important:

 For solid surface material installations such as

Surel™ and Corian

®

, consult with solid surface

manufacturer. Apply heat reflective tape such as

Scotch® Aluminum Foil Tape #425 or #427

around the cutout so that it folds over on the top

and sides.

 Do not wrap the tape underneath the cooktop.

Be sure the tape extends beyond the outermost

flange of the cooktop. All corners should be

covered with tape.

ENGLISH

Installation Manual

9

Electrical Connections

DANGER

Disconnect power before servicing the product.

Failure to do so could result in death or

electrical shock .

General information

WARNING

The models may be powered at 240V or

208V.

This cooktop does not require a neutral connection. If

the cooktop is to be completely enclosed in a cabinet,

feed the cooktop cable through the opening in the

cabinet. Make the electrical connection following the

appropriate steps for your installation.

Your cooktop must be connected to the proper

electrical voltage and frequency as specied in the

table on the right.

Figure 12. Location of serial tag

Connect with copper wire only

If the house has aluminum wiring, follow the

procedure below:

1. Connect the aluminum wiring to the copper wire

by using special connectors designed and

Underwriters Laboratories-listed for joining copper

to aluminum. Follow the electrical connector

manufact

urer's recommended procedure.

2. Aluminum/copper connection must conform with

local codes and industry- accepted wiring

practices.

The exible conduit (supplied) 3 feet long (100 cm)

located at the right rear of the cooktop bottom box

should be connected directly to junction box. Do not

cut the conduit. A U.L - or CSA - listed conduit

connector must be provided at each end of the power

supply cable (at the cooktop and at the junction box.)

A time delay fuse or circuit breaker is recommended.

Do not ground to a gas pipe. Do not have a fuse in the

grounding or neutral circuit.

Fuse both supply (phase) lines.

WARNING

Improper connection of aluminum house wiring to

the copper leads can result in a serious problem.

National Fire Protection Association

Batter/march Park Quincy, Massachusetts 02269

A three-wire, single phase, 240 Volt 60 cycle electrical

system (properly circuit protected to meet Local

Codes of NFPA No.70) must be provided. Unit must

be properly grounded in accordance with local wiring

code. The chart below recommends the minimum

circuit protector and wire size if the appliance is the

only unit on the circuit. If smaller sizes of wire are

used, the unit eciency will be reduced and a re

hazard may be created. It is advisable that the

electrical wiring and hookup be accomplished by a

competent electrician.

Model

Power Supply

240 V 60 Hz 208 V 60 Hz

Approval

code

30”

AN-2400

7,2kW 30A 6,2kW 29,8A 812T40IP

WARNING

This touch control works using optical light sensing

after a power failure, any direct strong light over the

sensor area may affect the touch control functionality.

When powering on the unit make sure that no strong

light is shining direct over the touch control zone,

it can compromise the start-up sensor calibration

resulting in an unresponsive touch control.

ENGLISH

Installation Manual

10

Recommended Minimum

kW Rating on

serial plate

Circuit protection

in amperes

Wire size

(AWG)

0-4.8

20 12

4.9-6.9

30 10

7.0-9.9

40 8

10.0-11.9

50 8

12.0-14.9

60 6

Be sure your appliance is properly installed and

grounded by a qualified technician. Ask your

dealer to recommend a qualified technician or an

authorized repair service. This cooktop does not

require a neutral connection. If the cooktop Is to

be completely enclosed In a cabinet, feed the

cooktop cable through the opening in the cabinet.

Make the electrical connection following the

appropriate steps for your installation.

This appliance is manufactured with a green ground

wire connected to the cooktop chassis. After making

sure that the power has been turned off, connect the

flexible conduit from the cooktop to the junction box

using a U.L. listed conduit connector. Figures 13 and

14 and the instructions provided below present the

most common way of connecting the cooktops. Your

local codes and ordinances, of course, take

precedence over these instructions. Complete

electrical connections according to local codes and

ordinances

DANGER

Risk of Electric Shock, frame grounded to

neutral of appliance through a link.

Grounding through the neutral conductor is prohibited

for new branch-circuit installations (1996 NEC);

mobile homes; and recreational vehicles, or in an area

where local codes prohibit grounding through the

neutral conductor.

3-Wire branch circuit

Where local codes allow the connection of ground

wire from the cooktop to the branch circuit neutral wire

(gray or white colored wire) proceed as follows (see

figure 13).

1. If local codes permit, connect the green GROUND

wire from the cooktop to the branch circuit neutral

wire (gray or white colored wire).

2. Connect the red and black leads from the cooktop

to the corresponding leads in the junction box.

Figure 1.

4-Wire branch circuit

Refer to figure 14:

1. Connect the green ground wire from the cooktop

to the ground wire in the junction box (bare or

green colored wire).

2. Connect the red and black leads from the cooktop

to the corresponding leads in the junction box.

3. Connect the white wire from the cooktop to the

neutral (gray or white) wire in the junction box.

4. Terminate and insulate the neutral (gray or white

colored wire) in the junction box.

Figure 1.

Page is loading ...

ESPAÑOL

Manual de Instalación

20

�



Figura 2.

LONGUITUD DEL CORTE

A

LONGUITUD DEL CORTE

B

1-1/2” (3.8CM)

ESPACIO MINIMO

VER NOTA

R

DESDE EL BORDE DEL

CORTE AL BORDE FRONTAL

DE LA ENCIMINERA

2-1/2” (6.5 cm)

SLOT PARA

CABLE

3-1/2” (9 cm)

2-1/2” (6.5 cm)

DIMENSIONES DEL HUECO DE ENCASTRE

1-1/4” (3,2 cm) Canada

2-1/4” (5,7cm) US

Figura 1.

21” 3/16 (53,8cm)

30” 3/8 (77,1cm)

2” 7/8 (7,4)

1/4” (0,6cm)

3” 1/8 (8cm)

1” (2,5cm)

1/4” (0,6cm)

2” 7/8 (7,4)

36” 3/16 (91,9cm)

21” 3/16 (53,8cm)

3”1/8 (8cm)

1” (2,5cm)

30’’

36’’

Page is loading ...

Ancona VECTIM365 User manual

This manual is also suitable for

Ancona VECTIM365 User manual

in other languages

Related papers

Other documents