Sloan Valve 3396075 Installation guide

Brand: Sloan Valve

Model: 3396075

Type: Installation guide

This manual is also suitable for

3396076

Code No. 0816188 – Rev. 4 (08/12)

ROYAL FLUSHOMETER MODELS

(Features High Back Pressure Vacuum

Breaker)

• VBF-72-A1

• VBF-73-A1with2”(50mm)Offset

REGAL FLUSHOMETER MODELS

• VBF-72-A2

• VBF-73-A2with2”(50mm)Offset

The Sloan vacuum breaker trap primer provides a constant

water seal in a floor drain. Each time the flushometer is

activated, a small amount of water is diverted to the floor

drain to maintain the water seal. This seal prevents

objectionable sewer gases from escaping into the air.

Perform the following functions using the rough-in guides illustrated in Figures A and B:

• Installflushometerfollowingtheinstructionsincludedwiththevalve.UsetheseinstructionstoreplaceONLYthe

instructions for a Vacuum Breaker Flush Connection.

• Installpipingfromconnectiononthefloordraintoadesiredlocationonthewall(determinedbyinstaller).(Sloan

doesnotsupplythepipingforthisconnection.)

Note:Besurethatapproximately1”(25mm)ofa½”(13mm)NPTmalepipeprotrudesfromthewall.

INSTALLATION INSTRUCTIONS VACUUM BREAKER

TRAP PRIMER

PRIOR TO INSTALLATION

TOOLS REQUIRED FOR INSTALLATION

INSTALLATION

TheseinstallationinstructionsreplaceONLYthestandardstepforaVacuumBreakerFlushConnectionInstallation.

• SmoothjawedspudwrenchorSloanA-50“Super-Wrench™”forcouplings

• TubeBender

• TubeCutter(ifnecessary)

• Threadsealant

LIMITED WARRANTY

Unlessotherwisenoted,SloanValveCompanywarrantsthisproduct,manufacturedandsoldforcommercialorindustrialuses,

tobefreefromdefectsinmaterialandworkmanshipforaperiodofthree(3)years(one(1)yearforspecialfinishes,SFfaucets,

PWTelectronicsand30daysforPWTsoftware)fromdateoffirstpurchase.Duringthisperiod,SloanValveCompanywill,atits

option,repair,replace,orrefundthepurchasepriceofanyproductwhichfailstoconformwiththiswarrantyundernormaluse

andservice.Thisshallbethesoleandexclusiveremedyunderthiswarranty.ProductsmustbereturnedtoSloanValveCom-

pany,atcustomer’scost.Noclaimswillbeallowedforlabor,transportationorothercosts.Thiswarrantyextendsonlytopersons

ororganizationswhopurchaseSloanValveCompany’sproductsdirectlyfromSloanValveCompanyforpurposeofresale.This

warrantydoesnotcoverthelifeofthebatteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS

SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

VBF-73-AWITH2”(50mm)

OFFSETAVAILABLEFORMODELS115

AND116ONLY.(FORUSEWITHGRAB

BARSINCLUDEDASPARTOFTHE

INSTALLATION.)

Figure A

CENTERLINE

OFFIXTURE

4¾”(121mm)

1”I.P.S.

SUPPLY

(DN25mm)

“C”

FIN.

FLOOR

FIN.

WALL

“B”

“A”

“C”

GRAB

BAR

2¼”MIN.

(57mm)

2”

(51mm)

“B”

“A”

4¼”MIN.

(108 mm)

Table1†

  “L” “A” “B” “C”

ForRoyalorRegal LengthofVacuum Centerlineof Centerlineof

FlushometerModel BreakerFlush SupplytoTopof SupplytoTrap CriticalLinetoTrap

  Connection Bowl PrimerOutlet PrimerOutlet

 110/111‡ 8½”(216mm) 11½”(292mm) 7”(178mm) 2¼”(57mm)

 113/113-1.6 13”(330mm) 16”(406mm) 11”(280mm) 6¼”(159mm)

 115/115-1.6 21”(533mm) 24”(610mm) 11”(280mm) 6¼”(159mm)

 116/116-1.6 24”(610mm) 27”(696mm) 11”(280mm) 6¼”(159mm)

  VBF-73-AWith2”(50mm)Offset

 115/115-1.6 22½”(572mm) 25”(635mm) 11”(280mm) 6¼”(159mm)

 116/116-1.6 25½”(648mm) 28”(711mm) 11”(280mm) 6¼”(159mm)

† RefertoFigureAfordimensions“A,”“B”and“C.”RefertoFigureBfordimensions“L”and“C.”

‡ ConsultlocalcodesforapprovaloftheuseoftheVBF-72trapprimerwithflushometermodels110/111.Some

codesrequireaminimumdistanceof6”(153mm)betweenthecriticallineofthevacuumbreakerandthetrap

primeroutlet.Inthesecases,specifymodels113,115or116.

Figure B

“L”

“C”

DISTANCETOBE

DETERMINEDBY

INSTALLER

CRITICALLINE

1½”(38mm)O.D.

VACUUMBREAKER

OUTLETTUBE

5/8”(16mm)

2¾”(70mm)

ELBOW

Insertthesmallerendoftheblackplasticwaterdeflectorintothethreadedendoftheelbowfitting.Theflatendofthe

elbow fitting will face outward from the vacuum breaker.

Placeseveraldropsofthreadsealantonthethreadsoftheelbowfitting.Inserttheelbowfittingandwaterdeflectorinto

thethreadedholeofthevacuumbreakertube.Screwthefittingintoplace.DONOTovertightenthisconnection.The

final position of the elbow should allow water flow from the vacuum breaker in a downward direction.

Figure1

Figure2

Figure3

Slidethespudcoupling,nylonslipgasket,

rubber gasket and spud flange (all supplied with

a standard flushometer vacuum breaker) over the

vacuum breaker tube and insert the tube into the

fixture spud. Tighten the spud coupling onto the

fixturespudbyhand.

VACUUMBREAKER

OUTLETTUBE

WATERDEFLECTOR

¼”I.P.S.

ELBOWFITTING

INSTALL

FITTING

INTHIS

RANGE

90°

1½”

(38mm)

WATER

DEFLECTOR

CENTERLINE

OFTRAP

PRIMER

WATER

FLOW

VACUUMBREAKER

OUTLETTUBE

ELBOWFITTING

WALLFLANGE

½”(13mm)NPTMALEPIPE

FORTRAPPRIMEROUTLET

½”(13mm)NPT

FEMALETUBEFITTING

1”

(25mm)

TRAP

FINISHEDWALL

VACUUM

BREAKERTUBE

RUBBER

GASKET

SPUD

FLANGE

SPUD

COUPLING

NYLONSLIP

GASKET

1-INSTALLWATERDEFLECTORANDELBOW(FIG.1)

2-INSTALLWALLFLANGE(FIG.2)

3-INSTALLVACUUMBREAKERFLUSHCONNECTION

(FIG.3)

Placewallflangeoverthe½”(13mm)NPTmalepipeusedasthetrapprimeroutlet.Pushwallflangeuntilitisflush

againstthewall.Connectthe½”(13mm)NPTfemaletubefittingtothepipe.Thefittingwillhelpkeepthewallflange

in position.

DONOTuseabrasiveorchemicalcleanerstocleanflushometers,theymaydullthelusterandattackthefinish.Use

ONLYsoapandwater,andthenwipedrywithacleantowelorcloth.Whencleaning,protecttheexposedflushometer

fromanysplatteringofcleaner.Acidsandcleaningfluidscandiscolororremovechromeplating.

Whenfurtherassistanceisrequired,please

contact Sloan Technical Support at:

1-888-SLOAN-14(1-888-756-2614).

ManufacturedintheU.S.A.bySloanValveCompanyunderoneormoreofthe

followingpatents:5,373,592;5,564,460.OtherPatentsPending:Permex

Prior to inserting the flex tube into the elbow fitting, ensure

that the restrictor washer has been inserted into the elbow

fitting. The restrictor washer prevents too much water from

beingdivertedawayfromthebowl.Thishelpsensure

optimal bowl performance, even when used with 1.28 gpf

(4.8Lpf)High-EfficiencyToilets.

Usethe3/8”(9mm)diameterflextubingtoconnectthe

bottom of the elbow fitting with the restriction washer to the

tubefittingatthewallflange.Sloanprovidesa12”(305

mm) length of flex tubing. Cut tubing to appropriate length.

Tighten compression fittings at both ends of the flex tubing.

Complete the valve installation according to the installation

instructionsincludedwithyourSloanflushometer.

Figure4

SLOANHEADQUARTERS•10500SEYMOURAVENUE•FRANKLINPARK,IL60131

Phone:1-800-9-VALVE-9or1-847-671-4300•Fax:1-800-447-8329or1-847-671-4380•http://www.sloanvalve.com

©2012SloanValveCompanyCodeNo.0816188–Rev.4(08/12)

10A

10B

VACUUM

BREAKER

OUTLET

TUBE

ELBOW

FITTING

RESTRICTION

WASHER

½”(13mm)NPT

FEMALETUBE