For Cemented, In-Ground Systems Only
COPY
2
INSTRUCTION #1028869 B
**U.S. and Canada customers ONLY**
IF ASSISTANCE IS NEEDED,
DO NOT CONTACT THE STORE!!!
CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) 225-3865
HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)
Call, or visit our Web site for Saturday hours.
Save this instruction in the event that the manufacturer has to be contacted for
replacement parts.
MODEL #12347
BALL RETURN NET
7/7/2012
**For customers outside the U.S. or Canada, please contact the store for assistance.**
For Cemented, In-Ground Systems Only
Register your product online at www.lifetime.com.
Maintaining your privacy is our long-standing policy at Lifetime. And you can rest assured that
Lifetime will not sell or provide your personal data to other third parties, or allow them to use your
personal data for their own purposes.
We invite you to read our privacy policy at www.lifetime.com
REGISTER today!
At Lifetime, we are committed to providing innovative and quality products. While registering, you
will have the opportunity to give us your feedback. Your input is valuable to us.
You can also opt-in to receive new product notifi cations or promotions.
In the unlikely event of a product recall or safety modifi cation, your registration provides the infor-
mation we need to notify you directly.
Registration is fast, easy, and completely voluntary.
COPY
3
WARNING
To ensure your safety, do not attempt to assemble this system without reading
and following all instructions carefully. Identify and inventory the parts using the
Parts List. Failure to comply with any of the warnings in these instructions may
result in serious personal injuries such as cuts, broken bones, nerve damage,
paralysis, brain injury, or death. Failure to comply may also result in property
damage. Please heed all warnings and cautions.
Most injuries are caused by misuse and/or not following instructions. Use caution when
using this system.
SAFETY INSTRUCTIONS
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check
entire box and inside all packing material for parts and/or additional instruction material. Before beginning
assembly, read the instructions and identify parts using the hardware identifier and parts list in this document.
Proper and complete assembly, use and supervision are essential for proper orientation and to reduce the risk
of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID
WARRANTY.
WARNING
• If using a ladder during assembly, use extreme caution.
• No climbing on net.
• Not for use on portable systems. Designed for cemented, in-ground systems only.
• This is a training aid. Not for use during game play.
• Remove after each use.
Not for use on portable systems. This product is designed for use with
cemented, in-ground systems only. Failure to follow this warning could result
in serious personal injury or property damage.
WARNING
4
1. Adjustable Wrench
2. One 60 lb. bag of sand
3. 7/16” Wrenches (2)
TOOLS AND MATERIALS REQUIRED FOR ASSEMBLY
(Not Included)
4. 3/4” Wrenches (2)
5. 3/8” Socket Wrench
6. Phillips Screwdriver
ID Part # Description Qty.
AA 1029635 Tube, Swaged 1
AB 1029636 Tube 1
AC 1029563 Net 1
AD 1029561 Weight Bag 2
Net Hardware (1029637)
NA BN00300 1/4”-20 Cap Nut 6
NB 1029478 1/4”-20 x 1 3/4” Hex Bolt 6
NC 1029479 1/4” Flat Washer 12
ND 1029560 Harness 1
NE 1031424 6 mm Screw 1
NF 1031444 1” Plug 2
NG 1028233 Bungee Cord 2
PARTS LIST
BEFORE BEGINNING ASSEMBLY
A. Keep the hardware bags and their contents separate. If any parts are
missing, call our Customer Service Department.
B. Test fit all Bolts by inserting them into their respective holes. If necessary,
carefully scrape away any excess powder coating buildup from inside
the holes. Do not scrape away all of the powder coating. Bare metal may
rust. You may need to pound some Bolts into place with a hammer or
mallet.
5
HARDWARE IS ACTUAL SIZE
(*Unless otherwise indicated)
NA NB
NC
*ND
NE
NF
*NG
*AA
*AB
*AC
*AD
Swaged end
6
Required For This Page:
1. Insert Swaged Tube (AA) into Tube (AB).
4. Place Tube Assembly between flaps of Net (AC) and align the six holes in the Tube
Assembly with the six holes in the Net flaps.
*AA
*AB
2. Secure the Tube Assembly together using one (1) 6 mm Screw (NE).
3. Insert a 1” Plug (NF) into each end of the Tube Assembly.
(2)
1029637
Screwdriver
AA
AB
NE
NF
NF
NF
NE
7
7/16” Wrenches
1029637
Required For This Page:
NA
NB
NC
5. Secure the Tube Assembly to the Net using one (1) 1/4”-20 x 1 3/4” Hex Bolt (NB),
two (2) 1/4” Flat Washers (NC), and one (1) 1/4”-20 Cap Nut (NA) for each hole.
(6)
(6)
(12)
NA NC
NC
NB
WARNING
Do not overtighten the Cap Nut. If the end of
the Bolt breaks through the plastic cap, call our
Customer Service Department at the number
on Page Two. Exposed threads on the end of
the Bolt may cause serious injuries.
8
*ND
1029637
Required For This Page:
6. Insert the straps of the Harness (ND) under and around the Tube Assembly as
shown.
7. Pull the straps of the Harness up through both the first and second rings.
Finally, loop the strap around Ring 2 and back through Ring 1 (as shown below).
Repeat for second strap.
ND
8. Pull down on the straps about six inches.
Ring 2
Ring 1
ND
Ring 2
9
WARNING: If using a ladder
during assembly, use extreme
caution.
9. Lower your rim to its lowest setting.
11. Tie the straps of the Harness to a fixed, non-moving point just behind the
backboard. Do not tie straps to extension arms.
10. Loop the Harness over the rim and
pull down on the straps until the Net
fits snug against the back of the rim
next to the backboard.
Note: Your fixed point behind the
Backboard may look different from
this picture.
12. Raise rim to desired height.
10
14. Connect one end of the Bungee Cords (NG) to Weight Bags and the other end to
the bottom corners of the Net.
15. Lift, do not drag, Weight Bags and spread them until Net is taut.
16. Remove Net when not in use.
13. Completely fill Weight Bags (AD) with sand (approximately 30 lb. each) and zip
closed.
NG
1029637
Required For This Page:
(2)
AD
(2)
Note: Avoid dropping Weight Bags. Set Weight Bags in desired locations.
11
Notes:
12
2011 Lifetime Products, Inc.
LIFETIME BASKETBALL EQUIPMENT
90-DAY LIMITED FACTORY WARRANTY
THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY
CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE.
1. Lifetime basketball equipment is warranted to the original purchaser to be free from defects
in material or workmanship for a period of 90 days from the date of original retail purchase. The
word “defects” is defined as imperfections that impair the use of the product. Defects resulting
from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due
to improper installation, alteration or accident. This warranty does not cover damage caused by
vandalism, rusting, “acts of nature” or any other event beyond the control of the manufacturer.
2. This warranty is nontransferable and is expressly limited to the repair or replacement of defec-
tive basketball equipment. If the equipment is defective within the terms of this warranty, Lifetime
Products, Inc. will repair or replace defective parts at no cost to the purchaser. Shipping charges
to and from the factory are not covered and are the responsibility of the purchaser. Labor charges
and related expenses for removal, installation or replacement of the basketball system or its com-
ponents are not covered under this warranty.
3. This warranty does not cover scratching or scuffing of the product that may result from normal
usage. In addition, defects resulting from intentional damage, negligence, unreasonable use or
hanging from the net or rim will void this warranty.
4. Liability for incidental or consequential damages is excluded to the extent permitted by law.
While every attempt is made to embody the highest degree of safety in all equipment, freedom
from injury cannot be guaranteed. The user assumes all risk of injury resulting from the use of
this product. All merchandise is sold on this condition, and no representative of the company
may waive or change this policy.
5. This product is not intended for institutional or commercial use; Lifetime Products, Inc. does not
assume any liability for such use. Institutional or commercial use will void the warranty.
6. This warranty is expressly in lieu of all other warranties, expressed or implied, including warran-
ties of merchantability or fitness for use. Neither Lifetime Products, Inc., nor any representative
assumes any other liability in connection with this product.
ALL WARRANTY CLAIMS MUST BE ACCOMPANIED BY A SALES RECEIPT.
To register the product, visit our Web site at www.lifetime.com
REPORT PRODUCT DEFECTS IN WRITING TO:
Lifetime Products, Inc., PO Box 160010 Cleareld, UT 84016-0010 or
call 1-800-225-3865 M-F 7 a.m. to 5 p.m. MST.
Please include your dated sales receipt and photographs of damaged parts.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
