Operator’s manual
Vibratory plate
DPS
1850, 3060
Model DPS
Document 5100010679
Issue 05.2015
Version 01
Language en
100_0000_0001.fm 2
Manufacturer
Wacker Neuson Produktion GmbH & Co. KG
Preussenstrasse 41
80809 Munich
www.wackerneuson.com
Tel.: +49-(0)89-354 02-0
Fax: +49-(0)89-354 02-390
Original operator's manual
Table of contents
3 5100010679IVZ.fm
1 Preface ...................................................................................................................................5
2 Introduction ...........................................................................................................................6
2.1 Application of the manual ............................................................................................................ 6
2.2 Storage location of the manual.................................................................................................... 6
2.3 Accident Prevention Regulations................................................................................................. 6
2.4 Additional information.................................................................................................................. 6
2.5 Target group................................................................................................................................ 6
2.6 Explanation of symbols................................................................................................................ 6
2.7 Wacker Neuson Contact partner ................................................................................................. 7
2.8 Limitation of liability...................................................................................................................... 7
2.9 Product identification of the machine........................................................................................... 7
3 Security ..................................................................................................................................8
3.1 Policy........................................................................................................................................... 8
3.2 Responsibility of the operator...................................................................................................... 8
3.3 Operator responsibilities.............................................................................................................. 9
3.4 Personnel qualification................................................................................................................. 9
3.5 General sources of danger .......................................................................................................... 9
3.6 General safety instructions .......................................................................................................... 9
3.7 Specific safety instructions - Vibratory plates............................................................................ 10
3.8 General safety instructions - Combustion engines.................................................................... 11
3.9 General safety instructions - Fuel, lubricants and coolants ....................................................... 11
3.10 Maintenance.............................................................................................................................. 11
3.11 Personal Protection Equipment................................................................................................. 12
3.12 Safety devices ........................................................................................................................... 13
3.13 Behavior in dangerous situations............................................................................................... 13
4 Safety and information labels ............................................................................................14
5 Setup and function ..............................................................................................................16
5.1 Standard package...................................................................................................................... 16
5.2 Application areas....................................................................................................................... 16
5.3 Brief description......................................................................................................................... 16
5.4 Versions..................................................................................................................................... 16
6 Components and operator's controls ...............................................................................17
6.1 Components .............................................................................................................................. 17
6.2 Operator's controls..................................................................................................................... 17
7 Transport ..............................................................................................................................18
7.1 Loading and transport................................................................................................................ 18
8 Operation .............................................................................................................................20
8.1 Before commissioning ............................................................................................................... 20
8.2 Notes about operation ............................................................................................................... 20
8.3 Commission............................................................................................................................... 22
8.4 Operation................................................................................................................................... 22
8.5 Decommissioning ...................................................................................................................... 22
9 Maintenance .........................................................................................................................23
9.1 Maintenance table ..................................................................................................................... 24
9.2 Maintenance jobs....................................................................................................................... 24
10 Troubleshooting ..................................................................................................................28
10.1 Fault table.................................................................................................................................. 28
Inhalt
Table of contents
5100010679IVZ.fm 4
11 Accessories .........................................................................................................................29
12 Technical data ......................................................................................................................30
12.1 DPS 1850 .................................................................................................................................. 30
12.2 DPS 3060 .................................................................................................................................. 31
12.3 Combustion engine.................................................................................................................... 32
13 Emission control systems information and warranty ......................................................33
EC declaration of conformity
.....................................................................................34
DIN EN ISO 9001 certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
1 Preface
5 100_0000_0002.fm
1 Preface
This operator's manual contains information and procedures for the safe operation and safe
maintenance of your Wacker Neuson machine. For your own safety and to protect against injuries, you
must thoroughly read the safety instructions, familiarize yourself with them and observe them at all times.
This operator's manual is not a manual for extensive maintenance or repair work. Such work must be
carried out by the Wacker Neuson service department or by certified technically trained personnel.
When building this machine, great value was placed on the safety of its operator. However, an improper
operation or improper maintenance can pose hazards. Please operate and maintain your
Wacker Neuson machine in accordance with the information in this operator's manual. It will reward your
attention by providing you with a trouble-free operation and high availability.
Defective machine parts must be replaced immediately!
Please contact your Wacker Neuson contact partner for questions regarding operation or maintenance.
All rights are reserved, in particular the right of duplication and distribution.
Copyright 2015 Wacker Neuson Produktion GmbH & Co. KG
This operator's manual - even in part - may only be reproduced, used, processed, copied or distributed
with the expressed, prior written consent from Wacker Neuson.
Any type of reproduction, distribution or storage on data carriers in any form or type that is not approved
by Wacker Neuson represents a violation of the valid copyright and will be prosecuted.
We reserve the express right to technical changes that are used to improve our machines or raise the
safety standard, even without special notice.
2 Introduction
100_0000_0013.fm 6
2 Introduction
2.1 Application of the manual
This manual is to be considered as part of the machine and must be securely stored for the entire service
life. This manual is to be passed on to each subsequent owner or user of this machine.
2.2 Storage location of the manual
This manual is a component of the machine and must be stored in the immediate vicinity of the machine
so as to be accessible to personnel at all times.
If the manual is lost or a second copy of this manual is needed, there are two options to obtain a
replacement:
Download from the Internet - www.wackerneuson.com
Contact a Wacker Neuson contact partner.
2.3 Accident Prevention Regulations
In addition to the notes and safety instructions in this manual, the local accident prevention regulations
and the national industrial safety regulations also apply.
2.4 Additional information
This manual applies to various machine types from one product series. For this reason, some
illustrations may vary slightly in appearance from the acquired machine. In addition, version-specific
components may be described that are not included in the standard package.
The information contained in this manual is based on machines that were manufactured at the time of
printing. Wacker Neuson reserves the right to make unannounced modifications to this information.
It must be ensured that possible modifications or supplements on the part of the manufacturer are
introduced in this manual immediately.
2.5 Target group
People who work with this machine must be trained regularly regarding the dangers of handling the
machine.
This operator's manual is intended for the following people:
Operating personnel:
These people are instructed in the machine and are informed of possible dangers in the event of
improper behavior.
Technically trained personnel:
These people have a professional training as well as additional knowledge and experience. They are
able to evaluate the tasks assigned to them and recognize potential dangers.
2.6 Explanation of symbols
This manual contains particularly emphasized safety instructions in the categories: DANGER,
WARNING, CAUTION and NOTE.
Before all work on and with this machine, the notes and safety instructions must have been read and
understood. All notes and safety instructions in this manual must also be passed on to the maintenance,
repair and transport personnel.
DANGER
This combination of the symbol and signal word indicates a hazardous situation that will
result in death or serious injury if not avoided.
WARNING
This combination of the symbol and signal word indicates a hazardous situation that can
result in death or serious injury if not avoided.
2 Introduction
7 100_0000_0013.fm
2.7 Wacker Neuson Contact partner
Depending on your country, your Wacker Neuson contact partner is Wacker Neuson service, a
Wacker Neuson affiliate or a Wacker Neuson dealer.
On the Internet under www.wackerneuson.com.
The manufacturer's address is found at the beginning of this manual.
2.8 Limitation of liability
For the following violations, Wacker Neuson dismisses any liability for personal injury or material
damage:
Failure to observe this manual.
Application in accordance with the intended purpose.
Application of untrained personnel.
Use of spare parts and accessories that are not approved.
Improper handling.
Structural modifications of any kind.
Failure to observe the "general terms and conditions" (GT&C).
2.9 Product identification of the machine
Data of the nameplate
The nameplate contains information that uniquely identifies this machine. This information is required for
ordering spare parts and when inquiring about technical issues.
Enter the information about the machine in the following table:
CAUTION
This combination of the symbol and signal word indicates a possible hazardous situation
that can result in minor injury and damage to the machine if not avoided.
NOTE
Supplementary information.
Item Designation Your information
1 Group and model
2 Year of manufacture
3 Serial number
4 Version number
5 Item number
3 Security
100_0202_si_0009.fm 8
3Security
3.1 Policy
In keeping with the latest technological developments
The machine is built in keeping with the latest technological developments and according to the
recognized technical safety rules. Nevertheless, improper use can result in hazards to life and limb of
the operator, third parties or to damage to the machine and other material assets.
Application in accordance with the intended purpose
The equipment may only be used for the following purposes:
Soil compaction.
Asphalt compaction.
Vibrating sett paving (paving stones).
The equipment may not be used for the following purposes:
Compaction of very cohesive soils.
Compaction of frozen soils.
Compaction of hard, non-compressible soils.
Compaction of non-load-bearing soils.
Application in accordance with the intended purpose also includes the observation of all notes and safety
instructions in this manual as well as complying with the prescribed care and maintenance instructions.
Any other or exceeding use is considered improper. The manufacturer's liability and warranty are
canceled for any damage resulting from improper use. The risk lies entirely with the operator.
Structural changes
Structural changes may not be made without written approval from the manufacturer. Unapproved
structural changes may result in this machine posing dangers for the operator and/or a third party as well
as cause machine damage.
In the event of unapproved structural changes, the manufacturer's liability and guarantee are also not
applicable.
The following cases are considered structural changes:
Opening the machine and a permanent removal of elements.
Installation of spare parts that do not originate from Wacker Neuson or are not comparable in the
design system and quality of the original parts.
Attaching accessories of any kind that do not originate from Wacker Neuson.
Spare parts or accessories from Wacker Neuson can be safely assembled or mounted.
3.2 Responsibility of the operator
The operator is the person who operates this machine for commercial or economical purposes or who
releases it to a third party for use/application and during operation bears the legal product responsibility
for the protection of the personnel or third party.
The operator must make the manual available to personnel at all times and make sure that the operator
has read and understood this manual.
The manual must be kept next to the machine or place of use.
The operator must hand over the manual to subsequent operators or owners of the machine.
The country-specific regulations, standards, and guidelines on accident prevention and environmental
protection must be observed. The operator’s manual must be supplemented with additional instructions
that take regulatory, national or generally applicable safety standards into consideration.
NOTE
Read and comply with all notes and safety instructions in this manual. Failure to comply
with these instructions can cause electric shock, fire and/or serious injuries as well as
damage to the machine and/or damage to other objects. Keep safety instructions and
notes for the future.
3 Security
9 100_0202_si_0009.fm
3.3 Operator responsibilities
Know and implement the applicable industrial safety regulations.
Use a risk assessment to identify the dangers that result from the working conditions at the site of
application.
Compile operating instructions for the operation of this machine.
Regularly check whether the operating instructions correspond to the current status of rules and
standards.
Clearly regulate and specify the responsibilities for operation, troubleshooting, maintenance and
cleaning.
Train personnel at regular intervals and inform them of possible dangers.
Provide the personnel with the necessary protective equipment.
3.4 Personnel qualification
This machine may only be operated and used by trained personnel.
In the event of misuse, misapplication or operation by untrained personnel, dangers threaten the health
of the operator or third parties and damage to or the complete failure of the machine also threatens.
In addition, the following previous conditions apply to the operator:
Be physically and mentally eligible.
No influence on the ability to respond on account of drugs, alcohol or medication.
Be familiar with the safety instructions in this manual.
Be familiar with the use of this machine in accordance with the intended purpose.
Have reached the minimum age of 18 to operate this machine.
Be instructed in the independent operation of the machine.
Be authorized to operate machines and systems independently according to the standards of safety
engineering.
3.5 General sources of danger
Residual dangers in particular are hazards when dealing with machines that, despite a safe design,
cannot be eliminated.
These residual dangers are not obvious and may be the source of a possible injury or health hazard.
If unforeseeable residual dangers occur, the operation of the machine is to be stopped immediately and
the competent supervisor is to be informed. This supervisor shall make the following decisions and
initiate everything required to eliminate the occurring risk.
If necessary, the machine manufacturer is to be informed.
3.6 General safety instructions
The safety instructions in this chapter include the "General Safety Instructions" that are listed in the
manual according to the applicable standards. There may be notes included that are not relevant for this
machine.
3.6.1 Working area
Before beginning work, familiarize yourself with the working environment, e.g. the load-bearing
capacity of the floor or obstacles in the vicinity.
Make working area safe for the public transport sector.
Necessary fuse protection of walls and ceilings, e.g. in trench applications.
Keep the working area tidy. Cluttered or dark working areas can cause accidents.
Working with this machine in explosive vicinities is prohibited.
Keep children and other people away when working with this machine. Distractions may cause a loss
of control of the machine.
Always secure the machine against tipping, rolling, sliding and falling over. Risk of injury!
3.6.2 Service
Only have the machine repaired or maintained by qualified technically trained personnel.
Only use original spare parts and accessories. This preserves the operational safety of the machine.
3.6.3 Safety of persons
Working under the influence of drugs, alcohol or medication can cause serious injuries.
Appropriate protective equipment is to be worn for all work. Appropriate protective equipment
reduces the risk of injury considerably.
3 Security
100_0202_si_0009.fm 10
Remove tools before operating the machine. Tools that are located on a rotating machine part can
be ejected and lead to serious injuries.
Always ensure a good footing.
Vibration-induced long-term damage cannot be ruled out entirely during longer periods of work with
this machine. For exact values of vibration measurement, see the Technical Data chapter.
Wear appropriate clothing. Keep baggy or loose clothing, gloves, jewelry and long hair away from
moving/rotating machine parts. Entanglement hazard!
Ensure that no other individuals are in the danger zone!
3.6.4 Handling and use
Handle machines with care. Do not operate machines with defective components or operator’s
controls. Immediately replace defective components or operator’s controls. Machines with defective
components or operator’s controls carry a high risk of injury!
The operator’s controls of the machine shall not be improperly locked, manipulated, or changed.
Use the machine, accessories, tools, etc. according to these instructions.
Properly store unused machines out of the reach of children. The machine may only be operated by
authorized personnel.
After operation, store the cooled machine in a locked, clean, frost-protected and dry location that is
inaccessible to other people and children.
3.7 Specific safety instructions - Vibratory plates
3.7.1 External influences
The vibratory plate may not be operated in the event of the following external influences:
In heavy rain on sloped surfaces. Risk of slipping!
Oil field environments - methane emergence from the soil. Explosion hazard!
In dry, easily flammable vegetation. Fire hazard!
In an explosive vicinity. Explosion hazard!
3.7.2 Operational safety
When operating the machine, ensure that no gas, water or electric lines and tubes are damaged.
The machine may not be operated in tunnels or closed spaces.
Pay the utmost attention near drops or slopes. Risk of crashing!
Do not leave the operator's position in accordance with the intended purpose while operating the
machine.
Do not leave the machine running unattended. Risk of injury!
Demarcate a large working area and keep unauthorized people away. Risk of injury!
Machine operators must ensure that people in the working area keep a minimum distance of 2 meters
from the running machine.
Do not use any starting aid sprays. These can cause misfires as well as engine damage. Fire hazard!
When operating the machine on unsuitable surfaces, always approach gradients from below and
always stand above the machine on the slope. The machine could slip or tip over.
Do not exceed the maximum permissible slanting position of the machine - possible failure of the
engine lubrication, see chapter Technical Data.
3.7.3 Minimum safety distances
Compaction work near buildings can cause damage to buildings. For this reason, all possible effects and
vibrations to the surrounding building must be checked in advance.
The relevant rules and regulations for measuring, evaluating and reducing vibration emissions -
especially the DIN 4150-3 - must be considered.
Wacker Neuson assumes no liability for any damage to buildings.
3 Security
11 100_0202_si_0009.fm
3.8 General safety instructions - Combustion engines
The following notes must be observed:
Before starting work, check the engine to ensure there are no leaks and cracks in the fuel lines, tank
and fuel cap.
Do not operate a defective engine. Immediately exchange damaged parts.
The pre-set engine speed may not be adjusted. This could lead to engine damage.
Make sure that the exhaust system of the engine is free of debris. Fire hazard!
Switch off the engine and allow to cool before refueling.
Use the correct fuel type. The fuel may not be mixed with other liquids.
Use clean filling aids for refueling. Do not spill fuel. Immediately wipe up any spilled fuel.
The engine may not be started near spilled fuel. Explosion hazard!
For operation in partially closed spaces, sufficient ventilation and aeration must be ensured. Do not
inhale exhaust fumes. Risk of poisoning!
The engine surface and exhaust system can quickly become extremely hot. Risk of burns!
3.9 General safety instructions - Fuel, lubricants and coolants
The following notes must be observed:
Always wear safety glasses and protective gloves when handling fuel, lubricants, and coolants. If
hydraulic oil, fuel, oil, or coolant gets into your eyes, see a doctor immediately.
Avoid direct skin contact with fuel, lubricants and coolants. Rinse skin immediately with water and
soap.
Do not eat or drink while working with fuel, lubricants and coolants.
Contaminated hydraulic oil or fuel from dirt or water can lead to premature wear or failure of the
machine
Dispose of spilled fuel, lubricants and coolants according to the applicable provisions for
environmental protection.
If fuel, lubricants and coolants escape from the machine, do not operate the machine any longer and
have it repaired immediately by the Wacker Neuson contact partner.
3.10 Maintenance
The following notes must be observed:
This machine may not be maintained, repaired, adjusted or cleaned while switched on. Disconnect
the starter battery when working on the electrical system!
Adhere to maintenance intervals.
After each maintenance or repair, the safety devices on this machine must be reattached.
Observe the maintenance schedule. Non-listed work must be taken over by the service department
of the Wacker Neuson contact partner.
Immediately replace worn or damaged machine parts. Only use spare parts from Wacker Neuson.
Keep the machine clean.
Missing, damaged or illegible safety labels must be replaced immediately. Safety labels contain
important information regarding the protection of the operator.
Maintenance jobs must be performed in a clean and dry vicinity (e.g. workshop).
NOTE
This machine is outfitted with an EPA-certified engine.
Changing the revolutions per minute (RPM) impacts the EPA-certification and the
emissions. Settings for this engine may only be changed by a professional.
For more information, contact the engine manufacturer or Wacker Neuson contact
partner.
3 Security
100_0202_si_0009.fm 12
3.11 Personal Protection Equipment
NOTE
In order to avoid possible injuries when dealing with this machine, personal protective
equipment must be worn for all work on and with this machine.
Pictogram Significance Description
Wear safety shoes! Safety shoes protect against crushing, falling parts
and slipping on slippery surfaces.
Wear protective gloves! Protective gloves protect against abrasions, cut
injuries, punctures as well as hot surfaces.
Wear ear protection! Ear protection protects against permanent hearing
damage.
NOTE
With this machine, the permissible, country-specific noise limit (personal rating level) may
be exceeded. Therefore, ear protection must be worn. For exact values of noise
emissions, refer to the Technical Data section.
Work particularly cautiously and pay attention when wearing ear protection, as your ability
to hear noises, such as screams or signal tones, is restricted.
Wacker Neuson recommends always wearing ear protection.
3 Security
13 100_0202_si_0009.fm
3.12 Safety devices
Safety devices protect the user of this machine from being exposed to existing hazards. These are
barriers (separating protective devices) or other technical measures. This prevents the user from being
exposed to a danger. The source of danger will be eliminated in certain situations or the danger will be
reduced.
This machine has the following safety equipment:
3.13 Behavior in dangerous situations
Preventative measures:
Always be prepared for accidents.
Keep first-aid equipment on hand.
Make personnel familiarized with accident reporting, first aid and rescue facilities.
Keep access routes clear for rescue vehicles.
Train personnel in first aid measures.
Measures in case of emergency:
Immediately switch off machine.
Bring injured and other people out of the danger zone.
Initiate first aid measures.
Alert rescue forces.
Keep access routes clear for rescue vehicles.
Inform the person responsible at the site of application.
Item Description
1 Belt guard
NOTE
Always tighten loosened screwed connections with the prescribed torque setting.
1
4 Safety and information labels
100_0202_ls_0010.fm 14
4 Safety and information labels
The following labels are located on the machine:
WARNING
Illegible symbols
Over time, labels and plates on the machine can become dirty or become unrecognizable
in some other way.
Keep all safety, warning and operating instructions on the machine in a good legible
condition.
Renew damaged labels and plates immediately.
DPS 1850Hb DPS 1850Ha
DPS 1850Hv DPS 3060Hv
1
2
3
4
1
2
3
4
1
2
3
4
5
1
2
4
3
6
4 Safety and information labels
15 100_0202_ls_0010.fm
Item Label Description
1 Start/Stop.
2 A falling machine can cause serious injuries.
Only lift a machine at the central lifting point with tested lifting
gear and tackle (safety load hook).
Do not lift the machine with an excavator bucket at the
central lifting point.
Do not lift the machine with a forklift at the central lifting
point.
3 Use personal protection equipment in order to avoid injuries
and health hazards:
Ear protection.
Read operator’s manual.
4 Guaranteed sound power level.
5 Eccentric weight adjustment/oil.
6 Eccentric weight adjustment.
0219259
0216633
0219175
5 Setup and function
100_0202_sf_0011.fm 16
5 Setup and function
5.1 Standard package
The machine is delivered fully assembled and is ready for operation out of the box.
The standard package includes:
Vibratory plate
Operator’s manual
5.2 Application areas
The vibratory plate is used for the compaction of soil and is used in gardening and landscaping, civil
engineering, road and highway construction as well as paving work.
5.3 Brief description
The vibratory plate is a machine used to compact soils.
The vibration required for the compaction is generated by the exciter firmly connected to the base plate.
This exciter is designed as a single directional, front mounted exciter with circular vibrations.
The drive motor attached to the engine console drives the exciter. The torque is firmly transferred
through the centrifugal clutch and the exciter V-belt.
At low engine speeds, the centrifugal clutch interrupts the force flow to the exciter and thereby allows a
flawless idling of the drive motor. The revolutions per minute (RPM) of the drive motor can be changed
at the throttle lever from full throttle to idling and to stop.
The engine console and base plate are connected to each other through 4 vibration-absorbing rubber
metal buffers. This damping prevents a transfer of the very high frequencies to the engine console. The
functionality of the drive motor therefore remains preserved, despite the high compaction performance.
The drive motor works according to the diesel principle, has a recoil starter, draws the combustion air
through a dry-type air cleaner and is air-cooled.
5.4 Versions
Various machine types are listed in this operator's manual:
Versions Description
DPS 1850Hb Basic - normal standard design
DPS 1850Hv Vario - with two compaction levels
DPS 1850Ha Asphalt - with water tank
DPS 3060Hv Vario - with adjustable compaction levels and transport device
6 Components and operator's controls
17 100_0202_cp_0007.fm
6 Components and operator's controls
6.1 Components
6.2 Operator's controls
Always keep displays and operator's controls of the machine clean, dry and free of oil and grease.
Operator's controls, such as the ON/OFF switch, throttle control handles, etc. may not be locked,
manipulated or changed without permission.
Control handle
The height of the control handle can be adjusted to the body size of the operator and case of application.
Exciter adjusting knob / lever
The centrifugal force can be adjusted with the exciter adjusting knob / lever - only activate at a standstill!
DPS 1850Hb/Hv DPS 1850Ha DPS 3060Hv
Item Designation Item Designation
1 Engine 6 Water tank (optional)
2 Base plate 7 Transport device (optional)
3 Exciter 8 Handle
4 Protective frame (optional) 9 Nameplate
5 Belt guard
DPS 1850Hb/Hv DPS 1850Ha DPS 3060Hv
Item Designation Item Designation
1 Control handle 3 Handle recoil starter
2 Throttle lever 4 Exciter adjusting knob / lever
1
2
3
5
8
9
1
2
3
4
5
6
8
9
1
2
3
4
5
7
8
9
1
2
3
4
1
2
3
1
2
3
4
7 Transport
100_0202_tr_0010.fm 18
7 Transport
7.1 Loading and transport
Previous conditions
To transport the vibratory plate, only use suitable lifting gear with a minimum load-bearing capacity
of 150 kg.
Always switch off the engine during transport!
Attach suitable tackle to the intended central lifting point.
Perform preparations
During loading and transport, the control handle must be locked in the vertical position or folded down.
WARNING
Improper handling can lead to injuries or serious material damage.
Read and observe all safety instructions in this operator's manual.
DANGER
Danger from falling.
A falling machine can cause serious injuries, for example from crushing.
Only suitable and tested lifting gear and tackle (safety load hooks) with a sufficient
load-bearing capacity can be used.
Only lift the machine at the central lifting point.
Reliably secure the machine to the lifting gear.
Do not lift the machine by the control handle and handle.
Leave the danger zone when lifting and do not stay under suspended loads.
WARNING
Risk of fire and explosion from fuel.
Escaping fuel may catch fire and cause serious burns.
Lift and transport the machine upright.
CAUTION
Since the central lifting point of the machine is fixed offset, the machine is not in the center
of gravity.
NOTE
Wacker Neuson recommends emptying the fuel tank prior to transport.
7 Transport
19 100_0202_tr_0010.fm
Lifting and lash down the machine
1. To lift the machine, mount suitable tackle to the central lifting point.
2. Carefully load the machine into or onto a stable means of transport capable of bearing the load.
3. After loading, lash down the machine on the means of transport so that it is secured against rolling,
sliding and tipping over. In the process, attach the tie-downs to the provided tie-down lugs.
The front handle can be used as a tie down. It is to be ensured in the process that the machine
does not tilt laterally (guide belt through the folded-down control handle).
Transport machine - Transport device (optional)
1. Release the lock with your foot.
2. Tilt the machine forward - the
transport device vibrates under the machine.
3. Place the machine back to the rear on the
transport device.
NOTE
Appoint a specialist flagman for a safe lifting operation.
Item Designation Item Designation
1 Central lifting point 2 Belt
Item Designation Item Designation
1 Lock 2 Transport device
1
2
2
1
2
8 Operation
100_0202_op_0012.fm 20
8 Operation
8.1 Before commissioning
8.1.1 Control procedures before commissioning
Check the machine and components for damage. In the event of visible damage, do not operate the
machine and immediately contact Wacker Neuson service.
Ensure that loose packaging material has been removed from the machine.
Check the fuel level.
Check the engine oil level.
Check the fuel lines for leak tightness.
Check to ensure the screwed connections are firmly seated.
8.2 Notes about operation
Operation on sloped surfaces
Always stand above the machine in a sloped area.
Only approach gradients from below (a gradient that can be easily driven up can also be driven down
without any risk).
Do not stand in the direction of descent of the machine.
Do not exceed the maximum permissible slanting position. See chapter Technical Data.
Only operate the machine in the maximum permissible slanting position for a short time.
WARNING
Improper handling can lead to injuries or serious material damage.
Read and observe all safety instructions in this operator's manual.
NOTE
Perform control procedures according to the Maintenance chapter. If necessary, top off
missing fuel, lubricants and coolants, see chapterTechnical Data.
WARNING
Danger of tipping
There is a serious risk of injury due to the machine slipping or tipping over.
Near edges, at least 2/3 of the machine must be on a load-bearing surface.
Turn off the machine and lift it back onto a load-bearing surface.
WARNING
Health hazard from exhaust fumes
The exhaust fumes of this engine contain chemicals, which the state of California
knows can cause cancer, birth defects or other reproductive damage.
NOTE
If the maximum permissible slanting position is exceeded, this results in a failure of the
engine lubrication and therefore inevitably causes a defect of important engine parts.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Wacker Neuson DPS1850H Basic User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Wacker Neuson DPU 3750Hts US User manual
-
Wacker Neuson DPS1850H Basic User manual
-
Wacker Neuson DPS1850H Basic User manual
-
Wacker Neuson BPU 2540A US User manual
-
-
Wacker Neuson DPU 3060H User manual
-
Wacker Neuson DPU 3050Hw US Army User manual
-
Wacker Neuson DPU 6555H User manual
-
-
Wacker Neuson DPU4045Yeh User manual
