Haier HWM55-918P User manual

Brand: Haier

Model: HWM55-918P

Category: Washing machines

Type: User manual

Haier HWM55-918P is a fully automatic washing machine with a range of features to make your laundry experience easier and more efficient. With its large capacity, you can wash and spin a large amount of laundry in one go, saving you time and effort. The machine also features a variety of wash cycles to choose from, so you can select the perfect cycle for your laundry needs. Additionally, the Haier HWM55-918P is equipped with a number of safety features, such as child lock and overflow protection, to ensure your safety and peace of mind while using the machine.

Please read this manual carefully

before using.

Retain it for future reference.

This manual is for

Fully automatic washing machine

User’s manual

HWM55-918P

the back cover

CONTENTS

Names of the parts

Safety precautions

Installation and adjustment

Preparation before washing

Put in the laundries

Usage of the detergent

Close the top lid

Use the operation buttons

Finish washing

Disposal after washing

Trouble-shooting Answer to question

Packing list

Specification

Please check if power receptacle has good earthing condition before

using to guarantee your safety.

Contents marked with that symbol are related to the

safety of the product and the personal safety of the

user. Please operate in strict conformity to the

contents, otherwise it may cause damage of the

machine or injure the personal safety of the user.

Contents marked with that symbol are actions forbidden

to perform. Performing of those actions may result in

damage of the machine or injure the personal safety of

the user.

Warning sign

Forbidden sign

Notes: All illustrations in this Manual are given for reference only. Your products and

accessories may show differences from these illustrations due to our

continuous improvement.

Hanging

hole

Top lid

Control panel seat

Filter cover

Inner tub

Pulsator

Control panel film

Liquid whitener inlet

Liquid detergent inlet

Cabinet

Adjustable leg

Adjustable leg film

Fixed leg

Lint filter

Back cover

Power line

Drain hose

Cabinet handle

Cabinet

handle

Water inlet valve

Water absorption

cushion

Names of the parts

Meaning and description of the symbols

Safety precautions

Do not let the machine share one receptacle with other

electric appliances. If the plugging into the receptacles

loose, do not use the plug any more.

Do not put the machine at damp place

like the bathroom. Never wash it with

water. Do not put wet laundries on the

control panel.

Do not use water hotter than 50 .

In case the washing machine is installed

on ground with carpet, do not block the

ventilation hole with carpet.

Ensure carpet does not

obstruct the

opening in

the bases.

Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.

Keep the pin of the power plug clean, if the power plug is polluted with dust,

please wipe with dry cloth carefully.

If the supply cord is damaged, it must be replaced by

the manufacturer or its service agent or a similarly

qualified person in order to avoid a hazard.

Carpet

Please plug the power plug on special

receptacle.Be sure to use three-pins

power receptacle .Ensure that the

earthing terminal of the power receptacle

is earthed reliably .Use electric

leakage protector if possible.

The washing machine must be positioned

so that the plug is accessible .Be sure to

pull the plug off and close the water faucet

in following cases:power failure,delivering

the machine ,setting the machine idle

or cleaning the machine.

Do not plug or pull the

power plug with wet hand.

The ventilation

holes at the

bottom

1.Do not wash water-proof laundries like

the raincoat,bike covers etc.to aviod

abnormal vibrations in spinning.

2.When washing the floating lanudries

(like down jacket etc.),pay attention to the

tags.Determine whether the laundries

can be washed by the machine according

to the tags(It can’t be washed by the

machine if there is no tag or the tag

doesn’t show that

the laundies

can be washed

by the machine .)

Do not decompose, repair or alter the

machine by yourself.

Do not put any hot or heavy items (such

as the kettle with hot water ) on the

washing machine.

Do not wash laundries with volatile

materials (such as thinner, petrol etc.)

This applianceis not intended for use by

persons(including children)with reduce

physical, sensory or mental capabilities,

of lack of experience and knowledge,

unless they have been given supervision

or instruction concerning use of the

appliance by a person responsible for

their safety.

Keep the machine away from direct

sunlight and heat source like the heater.

Safety precautions

Do not stretch hands into the working

machine. It is dangerous even if the

rotation is slow. Take special care of

the children.

Please check if the water faucet is open, and if the connection of the

water inlet pipe is proper.

It is suggested to use foamless washing powder.

Please don t use the washer in the environment below 0 C; if the washer

has been stored below 0 C, please be sure to ensure the washer is placed

under the room temperature more than 2 hours and then use otherwise

the washing effects may be lowered or the washer may be damaged.

Adjust the Installation position

The washing machine away from wall should be overrun 20mm. The largest

allowable slope of the shank base of the machine is 2 .The slanting or rough

ground will result in unstable running or stoppage of the machine. Please adjust it

with following methods:

Install the bottom plate

Please install and adjust the machine according to the requirement of the mannual.

It is very important to your security and correct operating the machine.

Adjust the adjustable leg:

Please lift up the side of the leg slightly,

twist the adjustable leg, make sure to

keep the washing machine in balance.

Usage of the drain hose

Hang the drain hose to a suitable height.

Do not step on or press

the drain hose.

0.7m<H 1.2m

Installation and adjustment

Insert the bottom plate to the pedestal from the front to

the back and the two fasteners to the opposite holes, then

install the bottom plate to the pedestal with the screw

by a cross screwdriver . See to the figure : (Please first

pull off the power plug from the receptacle

before installing.)

Carpet

Back

Front

Bottom plate

Screw

Two fasteners

High

Low

Adjustable

Confirm it’s horizontal

Hang the lead line to check if it is horizontal.

The drain hose shall be higher than the

water in the tub avoid to siphon.(It doesn’t

work normal as inleting water as drain)

2. Connect the other end to the water inlet valve .

NOTE:please check if the connection of the

water inlet pipe is proper

( As figure 2)

1.Close the water tap.

2. Pull off the water inlet hose from the water tap and washer

Take down the water inlet hose

Figure 2

Figure 1

the water faucet

The water inlet hose

Install the water inlet hose

1.Attach the water inlet hoses to water faucet . Using pliers,tighten

the coupling . (As figuer 1)

Check the connection between the water inlet hose and

the water tap

1.Swaying the hose gently to confirm if it is fastened stably .

2.After installation,open the tap to check if it is leaky.

3.Do not bend the hose with overstrain.

4.Before each usage please check if the connection

between the water inlet hose and the water tap is firm ,

so as to prevent dropping from improve installaiton position

5.After finish washing cycle please pay attention to turn

off the tap .

Jointer of the water inlet hose

Water absortion cushion

Jointer of the

water inlet valve

Preparation before washing

1.Connect the water inlet hose. Open

the water faucet.

2.Confirm that the washing machine is

earthed reliably. Then insert the

power plug into the receptacle. The

earth terminal shall not link to gas

pipeline and faucet water pipeline.

3.Put up the drain hose.

4.Slanting or uneven ground may result in

unstable working or abnormal noise. Please

make the machine stand horizontally.

a. Check if the laundries are applicable for washing with machine.

b.Please repa ir the damaged cloth before washing in order to avoid

the situation worse

c. Divide the laundries that are not colorfast from other laundries.

d. Put those laundries difficult to absorb water into water with hand.

e. For those laundries with heavy soil, please first remove the dirt like

mud or dust. For the parts with heavy soil, please apply detergent on

them in advance, which can make it easier to remove the soil.

f. For those laundries that may get lint ball and those with long fur, turn

it over before putting in.

g. Do not put those laundries polluted by chemicals into the washing

machine directly.

h.The foreign materials will result in damage of the machine

0.7m<H 1.2m

Check if the

laundries has

special

requirement

on washing

pay attention to following before washing the laundries.

Preparation before washing

Clear the pocket.

Take out the coin,

sand,hairpins ect.

To aviod the

problem that

the washing

machine can

not be operated

normally.

Tie the long

strips; fasten

the button;

close zippers.

The quantity of

the laundries

shall not be too

large .Stretch

and loosen the

laundries before

putting them in

the tub.

When the pulsator

is running,the

buttons of the

laundries may cause

noise.For the sake

of discretion,please

put the laundries

with buttons into

other laundries.

Put in the laundries

The capacity of washing and spinning of he machine refer to the

largest weight of the standard laundries under dry condition that can

be washed or spinned in one time. One time washing quantity shall

be lower than the rated capacity.

The thickness, size, type of the cloth will influence the actual washing

capacity. It is suitable for one time washing to put in reasonable amount

of laundries and the laundries can be turned round in washing.

Do not select the high water level for laundries less than 1.0kg ,so as

to avoid splashing of water.

How to use the whitener

Fill water to desired level .Dilute the

whitener with container. Pour it

slowly into the liquid whitener inlet.

Avoid using whitener on laundries

with colour or pattern as they are

prone to lose color .

The whitener shall not touch the

laundries directly.

Refer to the user's manual for the

usage and quantity of the whitener.

For powder whitener, please

dissolve it before use.

Access for detergent

Detergent box (lint filter)

Usage of the detergent

How to use the

washing powder

How to use the softener

It is suggested to put the

detergent into the washing

power box when the fuzzy

program is selected.

Directly dissolved in the

machine (not applicable

for fuzzy program)

1.Fill small quantity of water

2.Add the powder.Run for 30 seconds to dissolve

it completely.

3.Put in the laundries .Select suitable water level.

The instant dissolving of the washing powder:

1.Prepare warm water of 30°C and a container.

2.Add the powder while stirring to fully dissolve it .

In selecting quick program ,it is suggested to adopt

liquid detergent instead of washing powder to

guarantee the washing effect.

Put in the proper quantities detergent according to

the water level and the laundries quantities.

It is not suggested to use high sudsing detergent.

The dosage of detergent may be different because

of the different kinds of detergent .Please refer the

usage of detergent .

The usage and dose of the softener as per the speciﬁ cations

of softener.



Turn the inner tub,you will find a softener inlet as the figure 1,

open the cover,put the softener into the inlet as the figure 2.

Before washing,close the cover and the softener will drop into

the inner tub during the last time rinsing.



After the softener is put in,please don’t place for a long time

otherwise softener may solidify and cause flowing not smooth.

Please pay attention to clean because the softner is easy to curdle

Please dilute the softner when the softner’s concentration is high.

When the rinsing time is not twice ,Please don’t use softner to avoid

influence effect.



Figure 1

Figure 2

Open

Access for softener

Liquid whitener inlet

Control panel

Off

Description of the function of buttons

Mode and meaning of the indicators

On: indicate the program

about to run,or indicate

the selected mode or

POWER ON/OFF button

Use the operation buttons

Page 12

Remain time digitron

It displays "--" during detecting.

It displays total remained time during the running program(min).

Flashing: indicate the

running program, or indicate the selected mode or indicate the water level

Program

SOAK

Standard washing

Washing the woollen textiles

Applicable situation

Posthaste wash of the laundry

with light soil

WASH

Washing the relatively big thick or very

dirty laundries

The purpose is drying the inner tub

and the outer tub,which can avoid

growing mildew.

STANDARD

SOFT

QUICK

WASH

RINSE

SPIN

When the indicator light of WASH,

RINSE,SPIN is on,the program is set.

Fast washing for light soil laundries

(quicker than STANDARD program)

“WATER LEVEL” button

The washing machine can detect the laundries automatically during the

STANDARD program. After detection, it will set the water level to suitable

value among 29L ,37L,46L automatically.

You can also set water level by yourself. After the machine is started, it will

not set water level automatically. You shall push the START/PAUSE button

to make new setting.

If there's water inside the tub, the machine cannot detect the laundries and

will display water level 29L .If wet laundries are put in, it may display water

level 46L. You must set suitable water level by yourself.

If TUB DRY program is selected, the water level will not respond.

During operation of wash and rinse program, you can push down the water

level button to add water. When you release the button, or it reaches the

overflow water level, the machine will stop adding water.

The water level decided may be different from actual value because of the

different moisture level of the laundries.

The water level of rinsing will be higher than the water level of wash during

the STANDARD ,SOAK,SOFT and WASH RINSE SPIN program.(except

the highest water level or choosing the water level of rinsing by yourself)

The digitron displays the time remained (in minute)

before the washing is finished.

Push down the reserve button. The reserve indicator

light is on ,the digitron displays the reserve time of

finishing washing (in hour).The point light flashs to

indicate in reservation

Push the “DELAY”button to display the reserve mode.

Remove the left detergent from the

clothes and then rinse the clothes.

RINSE

SPIN

TUB DRY

Just run the washing cycle without

drainage cycle. The detergent was left

in the tub and can be recycled.

When the clothes are washed or

the clothes are quite wet,extra spin

is needed.

Release the child lock function :push down

“Program ” button for more than 5 seconds ,

After a beep sound,the child lock

function is released.

Child lock function

Push down the button for 5 seconds ,the digitron displays “CL”.Then you can continue setting desired washing procedures.After

setting ,push the “Start/pause” button, The child lock function is activated.All of the buttons are locked and can’t make selection

indicate the water level

“PROGRAM” button

After the power is switched on,

press it to start the machine .

During working push it to pause

During pause,push it to restart.

“Delay” button

“START/PAUSE” button

Push the power button to switch on the power

When the power is on push it again to switch off the

power .

Push the power button to switch on the power ,if the

start /pause button is not pushed the washing machine

will automatically switch off the power after 5 minutes.

When using the child lock function,if the top cover is opened,the machine will stop and display E2 alarm .After 15 minutes the

machine will automatic drainage .If you want to clear the E2 alarm ,please close the top cover and press the “Start/pause ”

button .The E2 alarm will be cleared.

It displays I remained reserved time during reserved

program(hours) .

It displays abnormal symbol in abnormal

situation.(See to Page12)

WATER LEVEL

DELAY

PROGRAM

START/PAUSE

POWER

Remain(Minutes)

Reserve(Hours)

Tub dry

Spin

Rinse

Wash

Standard

Soak

Soft

Quick

Solid

Flashing

18L

12L

29L24L

37L

33L

46L

41L

POWER

1.Push "POWER" button to switch on the power

2.Push " PROGRAM " button to select suitable

automatic program

Page 8

After the power is switched on,”STANDARD” is

automatically set. To select other fully-auto program,

please push the "PROGRAM” button till the relative indicator is light.

Refer to the " PROGRAM " button on Page 8.

PROGRAM

Step of using the operation buttons and description of

the steps

WATER LEVEL

DELAY

PROGRAM

POWER

START/PAUSE

Remain(Minutes)

Reserve(Hours)

Tub dry

Spin

Rinse

Wash

Standard

Soak

Soft

Quick

Solid

Flashing

18L

12L

29L24L

37L

33L

46L

41L

If “STANDARD”program is set ,the machine will execute fuzzy detection .The computer will

set the water level and wash time according to the cloth and weight of the laundries .The full

procedure is controlled automatically.

WATER LEVEL

3 Push the " WATER LEVEL "button,select suitable water level

Push the "START/PAUSE" button

START/PAUSE

Finish washing

Water pressure and water level influence the wash time.

If the "SOAK " program is selected,the machine will soak before washing,

rinsing,spinning(low water level soak for 10mins,mid level 20mins high

level 30mins)

When the "DELAY" function is activated, the indicator light of the program you have set

will be off. The "reserve (hour)" and "time remain" indicator lights will be on. During

reserve procedure, push the "DELAY" button to display the reserve mode.

To change the running program or cancel the reserve setting, you

need to switch off the power and make new selection.

Confirm the operation of reserve program

Page8

Push the "DELAY" button to select suitable reserve wash

program

the washing will finish

about 18 hours later

Close the top lid

If the top cover is opened , the washing machine will stop running and tweet during spinning.

After finishing washing,the machine will turn off the power automaticlly.

DELAY

After switching on the power, when select the standard program,the washing machine will

execute fuzzy program automatically to detect the cloth .After detection, it can set the water

level automatically. To select other water level, ﬁ rst push the “START/PAUSE” button, then

push the “WATER LEVEL” button to set the water level.

After switching on the power, the reserve time program is set to off mode automatically. If you

need to set the washing procedure to be ﬁ nished at delay time, please push the “DELAY”

button to set the reserve washing program. Refer to delay button in Page 8 for selection.

Even there's no water in the tub, the

spinning will start after a certain period.

Wash the laundries that are prone to lose

colors separately from other laundries.

When washing start or opening cover intermitting, the washing machine

will begin to work after a period time, this is normal phenomenon.

Wash and spin after putting the damageable

clothes into tuck net, to avoid scathe.

Attention

Clean the detergent box with water.

The method of dismantle and installation refer to the

usage of dismantle and in stallation lint filter.

Disposal after washing

After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise

it may influence your using the machine.

Please first pull off the power plug from the receptacle before cleaning.

Install

Dismantle

5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid

for some time (about 1 hour), then close the top lid.

2.Do not store water in the washing machine for a long period. Drain the water completely

after each using.

The filter screen of the

water inlet valve is likely

to be blocked by foreign

materials and influence the water inlet.

Please clean it with brush every two

months.

If the cabinet is dirty, wipe it with

wet cloth

Do not flush it directly with water.

Wipe it with neutral detergent.

Do not wipe it with thinner, petrol, alcohol etc.

1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).

4.Hang up the power cord and drain hose.

3.Be sure to pull off the power plug before maintenance.

Detergent box

The lint filter must be used during washing.

It must be cleaned in time after each using.

The methods of dismantle

and install lint filter 1 as follows:

The methods of dismantle and install lint filter 2

as follows:

1.Push down the spring piece

of the top lint filter to make the

claws out of the filter cover,and

then pull out the lint filter to get

it down(figure 1).

2.Pull the back cover of the lint

filter, and then you can get

down it off the front cover

(figure 2)of the lint the lint filter.

3.Sweep the rubbish in the lint

filter.

4.Put the back cover of the lint

filter into the front cover .

(figure 3)

5.Put the lint filter into filter

cover, and make it tight.

1.Pinch the flexible film on the top of lint filter

(detergent box) and pull it out. Remove the spindle

at the bottom of the lint filter from the "凹" shape

of the filter cover along the direction of the arrow

diagram (arrow up for ). Remove the other side of

the spindle directly from the filter cover slot then

can remove the lint filter.

2.Pinch the left and right sides of the horizontal

bars on the top of the back cover of lint filter, rotate

along the assembly axis of the front cover of the lint

filter and the bottom of back cover of the lint filter,

open the back cover of lint filter(figure 3) .

3.Sweep the rubbish in the lint filter.

4.Rotate the back cover of lint filter along the assembly

axis and clamp on the lint filter former cover (figure 3).

5.Insert one bottom side spindle of the lint filter into the

corresponding "凹" shape install slot at the filter

cover bottom. Then clamp the other side spindle into the

"凹" shape at the filter cover along the arrow in the picture

(arrow down for install).At last pinch the horizontal bars

on the top of the lint filter and clamp it into the filter cover.

The top

The lint filter 2

The filter cover

The lint

filter 1

The front cover

of the lint filter

the front cover of the lint filter

The back cover of lint filter

The bottom

the bottom

dismantle

Filter cover

Figure 1

Figure 2

Figure 3

Make sure the lint filter is well installed, or it can influence your use.

dismantle

install

Trouble-shooting · Answer to question

When using the child lock function,

if the top cover is opened, the

machine will stop and display E2

alarm. After 15 seconds the machine

will automatic drainage

Clear the E2 alarm, please close the top

cover and press the “START/PAUSE”

button. Then E2 alarm will be cleared.

Phenomena The reason How to settle

The digitron displays E0. The top lid is open during

reserve procedure.

Close the top lid.

The drainage cannot

work, or is too slow. The

digitron displays E1.

Is the drain hose blocked?

Clean the foreign material. Open and



close the top lid once.

It stops running in

midway. The digitron

displays E2.

The top lid is not closed.

Close the top lid.



The safety switch acts,

and the spinning cannot

work. The digitron

displays E3.

Are the laundries put slantingly?

Is the machine slanting?

Reorder the laundries. Close the top lid.

Place the machine horizontally, open

and close the top lid once.



The water ﬁlling does

not work, or is slow, the

digitron displays E4.

Is the water tap opened, or is

there water supply failure?

Is the water inlet valve blocked?

Is the water pressure too low?

Open the water tap. Open and close the

top lid once.

Clean the water inlet valve then open

and close the top lid once.

Use after the water pressure is normal.

The digitron displays E6.

The digitron displays F2.

The water level sensor is bad. Please contact the after-sales service 

department.

Please contact the after-sales service

department.

The

machine

does not

act

Not wash

Is there power failure?

Is the power plug inserted tightly?

Is the water level reached preset

position?

Please use it when there’s power 

supply.

Insert the power plug tightly.

Fill water to the preset position.

Not spin

Is the power plug inserted tightly?

Is the top lid closed reliably?

Are the laundries set ﬂat?

Insert the power plug tightly.

Close the top lid.

Set the laundries ﬂat.

The water tap leaks

There is abnormal sound

inside the machine

Is the screw of the jointer of water

inlet hose loose or awry?

Is the machine slanting?

Are the laundries put slantingly in

spinning?

Are there any foreign materials?

Fasten the screw of the jointer properly. 

Adjust the machine to be even

Reorder the laundries and close the top

lid.

Remove the foreign materials.



(If there’s breakdown, please pull off the power plug before checking)

The following phenomenon are not breakdowns sometimes. Please conﬁrm again before sending it to

repair.

If there are real breakdowns, please come to the special maintenance department or after-sale

service department of our company. Do not repair it by yourself.

Overflow alarm

Packing list

Name

Quantity

User's manual

One piece

Water inlet hose

One piece

Tapping screw

One set

The side of connection between the water inlet

hose and the washing machine

The side of connection between the jointer of

the water inlet hose and the water faucet

Phenomena Explanation

The spinning is intermittent when it starts. Balance the laundries to avoid slanting.

Push the “spin” button to select “Spin”, but it doesn’t

work.

The program is setting the drain time. Some time is

needed before it starts spinning.

There may be some water flowing out of the drain hose

in the first use of the machine.

It is the water remained in the factory inspection of

performance.

The pulsator pauses during water inlet in wash

and rinse.

It is to avoid splashing during water inlet.

Common phenomena

Fully automatic washing machine

Bottom plate

Warranty card

Put between the up gasket and

the up seal of the packing box

Injection pressure(MPa)

Specification

Washing/spinning capacity

5.5kg/5.5kg

Rated voltage/frequency

0.03MPa 1.0MPa

～

1/12L 2/18L 3/24L 4/29L

5/33L 6/37L 7/41L 8/46L

220V /50Hz

Water level/Water quantity(about)

Haier HWM55-918P User manual

Brand: Haier

Model: HWM55-918P

Category: Washing machines

Type: User manual

Download PDF

report

Haier HWM55-918P User manual

Haier HWM55-918P User manual

Related papers

Other documents