VDO Dayton DV 1805 MP3 User manual

Brand: VDO Dayton

Model: DV 1805 MP3

Category: Car media receivers

Type: User manual

U se r m a n u a l

M o d e d

’e m p lo i

B e d ie n u n g sa n le itu n g

G e b ru ik sa a n w ijz in g

Istru z io n i d

�u so

In stru ccio n e s d e m a n e jo

M o d o d e e m p re g o

B ru k sa n v isn in g

B e tje n in g sv e jle d n in g

� � y tt� o h je

� � � .v d o d a y to n .co m

DV1805 MP3

�

Siemens VDO - DV1805 DFU.book Page 4 Friday, September 2, 2005 5:32 PM

1. Flip Down panel release button

2. Volume rotary button

3. Power ON/OFF button

4. BAND button

5. CD slot

6. LCD display

7. AF/PTY/ENTER/MENU/PBC button

8. DISPLAY/SETUP button

9. TA/SMART button

10. TUNE/SEEK forward button

11. TUNE/SEEK backward button

12. SOURCE button

13. UP button

14. DOWN button

15. CD eject button

16. Radio preset 6 button/PAUSE & PLAY

17. Radio preset 5 button/STOP

18. Radio preset 4 button

19. Radio preset 3 button/SCN

20. Radio preset 2 button/RPT

21. Radio preset 1 button/RND

22. Sound button

23. AST button

24. Blinking LED

25. Reset button

26. Detachable unit connector

27. Remote control IR

313

14 21 20 19 18 17 16 4

2425

Siemens VDO - DV1805 DFU.book Page 3 Friday, September 2, 2005 9:07 PM

Siemens VDO - DV1805 DFU.book Page 4 Friday, September 2, 2005 5:32 PM

(A)

Release Panel

(B)

Insert Panel

** For this accessory,

contact your dealer

15A

Audio(SMART)

(White)

(Red)

Video

TEL MUTE HIGH (PINK)

TEL MUTE LOW (GREY)

HAND BRAKE CONTROL(Orange)

Multimedia control (Yellow)

External IR

ANT

Line out-Black

AUX IN-GREY

Tel Mute

(Low active)-Gray

(High active)-Pink

Line out AMP control

+ +

(Red)

(White)

(Red)

(White)

( Power remote)Green -

English

BEFORE YOU START...

Thank you for purchase this product

which has been designed and

manufactured to the highest standards

and subjected to rigorous testing.

Kindly familiarise yourself with the product

by reading this user manual. Keep this

manual handy in your car for future

reference.

IMPORTANT

This device has been designed and

produced according to applicable Safety

Regulations. Please read carefully the

instruction manual and use the device as

intended.

On safety

• To comply with the Traffic Laws in your

country, it is advisable to connect the

“Parking Brake cable” from headunit to

the car parking brake.

• The monitor connected to the video

out turns off automatically when the

parking brake is not applied.

CONTENTS

Hints For Correct And Safe Operation ..5

Installation .............................................5

Using The Detached Panel ...................6

Security Identification Number ..............6

Location And Functions Keys................8

Function selection mode Operation.......9

General Operation...............................10

Radio Operation ..................................11

RDS (Radio Data System) Operation..11

Advanced RDS Settings......................12

CD/MP3 Operation..............................13

DVD/VCD Operation ...........................14

Basic Operation...................................14

OSD (On Screen Display) ...................15

OSD Advanced Operation For Mp3 ....15

OSD Advanced Operation

(For JPEG File) ...................................16

Color / Brightness / Contrast Setting...16

Init Settings / Init Menu........................17

General Setup .....................................17

Speaker Set-up Menu .........................18

Audio-setup .........................................18

Preference Set Up ..............................19

Special Feature Functions ..................19

Specification........................................21

Maintenance .......................................22

Trouble shooting .................................23

HINTS FOR CORRECT AND SAFE

OPERATION

This unit is designed to be operated only

+12 volt DC negative ground systems.

The unit cannot be used on +24 volt or

positive ground systems.

The unit may not operate correctly in

extremely hot or cold temperatures.

The unit is equipped with a built in

self-protection circuit. When the

temperature reaches the factory preset

level, the protection circuit halts all unit

operation. If this happen, let the unit

settles to the car ambient temperature

before it sets back to normal operation.

INSTALLATION

Notes:

• Choose the mounting location where

the unit will not interfere with the

normal driving function of the driver.

• Before finally installing the unit,

connect the wiring temporarily and

make sure the unit and the system

work properly.

• Use only the parts included with the

unit to ensure proper installation. The

use of unauthorized parts can cause

malfunctions.

• Consult your nearest dealer if

installation requires drilling of holes or

other modifications of the vehicle.

• Install the unit where it does not get in

the Driver’s way and cannot injure the

passenger if there is a sudden stop,

like an emergency stop.

• If the installation angle exceeds 30°

from horizontal, the unit might not give

its optimum performance.

• If for any reason, the fuse is blown,

only replace with an automotive blade

fuse of the same rating.

Siemens VDO - DV1805 DFU.book Page 5 Thursday, October 27, 2005 1:26 PM

• Avoid installing the unit where it would

be subject to high temperature, such

as from direct sunlight, or from hot air,

from the heater, or where it would be

subject to dust, dirt or excessive

vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either

from “Front” (conventional DIN

Front-menu) or “Rear” (JIN or Japanese)

mounting. For details, refer to the

following illustrated installation methods.

DIN FRONT-MOUNT (Method A)

Installation of the unit

1. Metal Sleeve

Install the metal sleeve in the

dashboard. For optimal performance

of the CD player, the metal sleeve

should be positioned horizontally

(between -10 and +30). Fix metal

sleeve into place by pressing the

metal tags outwards using

screwdriver.

2. Front Mounting

Slide the radio into the metal sleeve

until the springs at either side of the

radio snap into the openings of the

sleeve.

3. Removing Radio

Insert the levers supplied with the unit

into the grooves at both sides of the

unit until they lock. Pull the levers

toward you makes it possible to

remove the unit from the dashboard.

DIN REAR-MOUNT (Method B)

Installation using the screw holes on the

sides of the unit.

Remove the outer rim around the front

panel and the side springs. Select a

position where the screw holes of the

mounting bracket and the screw holes of

the radio become aligned and tighten the

screws at 2 places on each side.

USING THE DETACHED PANEL

See details at the back of the cover page

for remove (figure A) and install (figure B)

the front panel.

1. Press the release button and pull-off

the front panel. Keep front panel into

the case.

2. To install the front panel, insert the

panel into the housing and make sure

the panel is properly installed,

otherwise, abnormalities occurs on

the display or some keys will not

function properly.

SECURITY IDENTIFICATION NUMBER

• A Security identification number is

stated on the Security Card.

Show this card as a proof of ownership,

when the set is stolen, when the

detachable Front is lost or when

requesting service.

• Do not keep the “Security Card” in

your car.

281

Siemens VDO - DV1805 DFU.book Page 6 Thursday, October 27, 2005 1:26 PM

English

REMOTE CONTROL

Siemens VDO - DV1805 DFU.book Page 7 Thursday, October 27, 2005 1:26 PM

LOCATION AND FUNCTIONS KEYS

1. Power Long press POWER to turn the unit ON or OFF. Short press to

MUTE the set

2. 0-9 Numeric buttons for preset/Tracks selection.

3. SMART In DVD mode, press it shortly to enter SMART MODE function.

(For details, refer to the SMART mode function description)

4. AST(STOP) In radio mode, press to enter into automatic memory.

In Disc mode, press it to stop disc playback.

5. / Tuner: scan up/down

MP3: 10 track up/down

CD: 5 track up/down

VCD: 5 track up/down (when PBC is OFF)

DVD: title up/down

In OSD mode, / buttons served as cursor buttons to select

item ahead/backward in up/down direction.

6. ( ) /

()

Tuner: S/P=Search up/down, L/P=manual up/down (only Tuner).

CD/MP3: S/P=track up/down, L/P=track FF/FRW (button release will

resume play)

VCD: S/P=track up/down, L/P=search up/down in speed of x2, x4,

x6, x8.

DVD: S/P=chapter up/down, L/P=rearch up/down in speed of x2, x4,

x6, x8.

In OSD mode, / served as cursor buttons to select item ahead/

backward.

7. SUB-T Changing of the SUBTITLE language on multi-subtitle language

DVD Disc.

8. INIT To activate OSD initialization menu.

9. TITLE Display the TITLE menu that is stored in DVD disc.

10. DISP Display statistical disc information during playback.

11. BAND(ILLUM) S/P-In radio mode, press it to select desired bands.

L/P-Brightness level low/hight selection.

12. Press to play/pause the disc.

13. SLOW(ZOOM) S/P-changing for slow playback motion. L/P-allows the picture to be

increased in size. (only in DVD mode)

14. ENTER(PTY) In CD mode, confirm the Track/Chapter selected with the numeric

buttons or selected with the cursor buttons on screen display.

In radio mode, long press to select program (RDS function).

PTY MUSIC group->PTY SPEECH group->PTY off.

15. MENU In DVD mode, display the root menu that is stored on the DVD disc.

Changing between PBC ON and PBC OFF on the VCD disc.

16. VOL+ Press VOL+ button to increase the volume level.

17. SOUND Press to select the desired adjustment mode, follow with VOL+/- to

change settings.

18. SOURCE Changing between radio mode, disc (DVD/VCD/CD/MP3) play

mode and AUX- IN modes.

19. ANGLE(AUDIO) S/P-Changing of the view angle on multi-angle DVD disc.

L/P-Press and hold the button for several seconds to change the

AUDIO soundtrack on multi-audio soundtrack DVD disc.

20. VOL- Press VOL- button to decrease the volume level.

Siemens VDO - DV1805 DFU.book Page 8 Thursday, October 27, 2005 1:26 PM

English

Function selection mode OPERATION

SET UP mode operation

Long press DISP button (8) more than 2 seconds to activate the set up mode and

change the desired setting accordingly.

Short press DISP button (8) on desired mode changes the display information as

below listed tables.

Set-up mode

Subject Options

Illumination Color 1 / 2 / 3

Bleep level BLEEP OFF, 1, 2, 3, 4

Manual Clock ON / OFF / RDS CLOCK

Clock format (if active) 24 Hr / 12 Hr

Time Adjust Hours (if man.clock) Hours blinking 00-12 or 23

Time Adjust Min’s (if man.clock) Minutes blinking 00-59

Tuner configuration Europe / USA / Asia

RDS ON / OFF

REGIONAL ON / OFF

TA - Volume TAVOL -2, -1, 0, 1, 2

LO / DX LO / DX

MW ON / OFF

LW ON / OFF

Freq SCAN OFF / SCAN 5, 10, 20 sec

CD level CD level -3, -2, -1, 0, 1, 2, 3

MP3 level MP3 level -3, -2, -1, 0, 1, 2, 3

AUX-In ON / OFF

AUX-IN level AUXLEV 1, 2, 3, 4

HANDSFREE HFREE OFF, MUTE, LO, HI

HANDSFREE LEVEL HFL 1, 2, 3, 4

LED (blinking) ON / OFF

• Use / to select subject

• Volume knob to select options

• The new selection is immediately memorised

Display key (on head unit)

Sequential information

Tuner Mode CD Mode MP3 Mode

Station Name

Frequency

RDS Clock

PTY

Elapsed Track / Time

radio info (freq, station..)

Clock

Title / Track time

radio info (freq, station..)

Clock

VCD Mode DVD Mode

Elasped Track / Time

radio info (freq, Station..)

Clock

Elasped Track / Time / Title / Chapter

radio info (freq, station..)

After 5 sec, return to the main display

Siemens VDO - DV1805 DFU.book Page 9 Thursday, October 27, 2005 1:26 PM

GENERAL OPERATION

ON/OFF

Long press the VOL knob on the panel or

POWER on the remote to turn on the unit.

Another long press will turn it off.

FACEPLATE RELEASE

Press REL button (1) on the panel, to flip

and take out the panel follow as figure 1.0.

SOUND ADJUSTMENT

Press SOUND button (22) to select the

desired adjustment mode. The

adjustment mode will change in the

following order:

By turning volume knob button (2),

different setting levels can be adjusted.

Note: Bass/Treble selections are only

active when the DSP (Digital Sound

Processor) is switched off.

Press SOUND button (22) for 2 seconds,

it will trigger a series of advanced RDS

setting.

Refer to RDS (radio data system)

operation section for details.

A/. DSP mode

Press SOUND button (22) to turn on

sound DSP function (Digital Sound

Processor) and to select desired audio

mode.

There are five kinds of mode as below:

Activating the DSP overrides the prior

selected Bass/Treble settings.

B/. Bass Boost mode

Activate Bass Boost mode by SOUND

button (22) and select desired Bass

Boost effect as rotate Volume button (2)

There are four kinds of mode as below

FLASHING LED

If the front panel is removed from the unit,

the LED (24) will be flashing.

Display key (on Remote Control): Sequential information shows on OSD monitor

Tuner Mode CD Mode MP3 Mode VCD Mode DVD Mode

no action 1) single elapsed 1) single elapsed 1) single elapsed 1) title nr/

total little nr/

chapter nr/

total. chapter nr/

elapsed time

2) single remain 2) single remain 2) single remain 2) title remain

3) total elasped 3) clear message

on screen

3) total elasped

(only when

PBC is off

3) chapter elasped

4) total remain 4) total remain

(only when

PBC is off)

4) chapter

remain

5) clear message

on screen

5) clear message

on screen

5) clear message

on screen

n.b : Once the OSD is on, it will not go off till the user switch to CLEAR screen

Item Range of adjustment

DSP OFF FLAT CLASSIC POP ROCK

Volume 080

Bass -14 0 +14

Treble -14 0 +14

Balance -15 0 +15

Fader -15 0 +15

Bass Boost OFF BB 1 BB 2 BB 3

Volume Bass Treble

Balance

Fader

DSP

Bass Boost

FLAT CLASSIC POP ROCK DSP OFF

OFF BB1 BB2 BB3

Siemens VDO - DV1805 DFU.book Page 10 Thursday, October 27, 2005 1:26 PM

English

RESET

RESET button (25) is placed on the front

panel and must be activated with either a

ball point pen or thin hard object.

The RESET button (25) is to be activated

for the following reasons:

- All the function buttons do not operate.

- Error symbol on the display.

Note: Pressing the RESET button (25)

will erase your stored stations in the

memory.

SOURCE

Press button (12) to switch between Disc,

Radio and Aux-In.

MUTE

Press volume button (2) to silence the

receiver. Press it again to resume

listening.

RADIO OPERATION

BAND SELECTION

At tuner mode, press BND button (4)

shortly to select the desired band. The

reception band will change in the following

order:

STATION SELECTION

Press button (10) or button (11)

shortly to activate automatic seek

function.

Press for 2 seconds till “MANUAL”

appeared on the display, the manual to

activate the manual mode. If both buttons

have not pressed for several seconds,

they will retune to seek tuning mode and

get back automatic seek function.

AUTOSTORE

- Automatic Memory Storing

Press AST (23), the radio searches for

6 strongest stations and stores them into

the presets of the current selected band.

Note: Any stations that were previously

stored in this memory bank are replaced

by the new stations.

FREQ SCAN

Press up/down buttons (13/14) shortly

to scan all frequency throughout the

entire band.

Note: SCAN in SETUP mode has to be

turned on before it can function.

STATION STORE AND RECALL

Press any one of the preset buttons

(1 to 6) to recall a station which had been

stored in the memory. Press a preset

button for 2 seconds, previous preset

station can be overwritten by current

tuned frequency.

RDS (RADIO DATA SYSTEM)

OPERATION

The RDS data are the PI, PS, TP, PTY,

TA and AF data.

PI: Program Identification Code

Code for identifying program

PS: Program Service Name

Broadcast station name data

expressed in alphanumerically

character

TP: Traffic Program Identification

Identification data for traffic

information broadcasting station

TA: Traffic Announcement Identification

Identification data showing traffic

information is being transmitted

or not

AF: Alternative Frequencies

Frequency list of broadcasting

station transmitting the same

program

Setting AF Mode

- Press AF button (7)

briefly to switch on/off AF mode.

- Whenever AF is switched on, Symbol

“AF” appears on the display.

- The tuner will return to Alternative

Frequencies whenever the reception

signals getting worse.

- ALARM will be displayed when an

emergency broadcasting is r eceived;

meanwhile sound output level will be

adjusted to the preset output level

automatically when the volume contr ol

is set at minimum.

FM1 FM2 FM3 MW1

MW2

Siemens VDO - DV1805 DFU.book Page 11 Thursday, October 27, 2005 1:26 PM

Using PTY to Select Program

The PTY function allows you to search for

stations with a particular Program Type.

To select your program type, long press

on PTY button (7)

Now you can select the music type or

speech type using preset keys 1 - 6 for

your selection as listed in below table:

While selecting PTY engagement, its

selection is implemented by preset button

as described in notes.

When PTY is selected, the radio starts to

search corresponding PTY information,

and stops of the corresponding PTY

information is detected. If corresponding

PTY information is not found, normal radio

reception is resumed.

Listening to Traffic Announcement

Traffic announcement can interrupt CD

play or radio listening when broadcast.

Briefly press the TA button (9) to select

the TA mode on or off.

When TA mode is on, you will hear the

Traffic Announcement when broadcast.

During traffic announcement, you can

interrupt it by short press of TA button (9)

without switching off the TA mode.

By doing so, the set will return to the

previous operating mode.

ADVANCED RDS SETTINGS

Press the SOUND button (22) for

2 seconds to enter the advanced RDS

settings menu.

a) TA SEEK or TA ALARM

- TA SEEK mode:

When TP information gets lost at the

current station for retune time which

is set by RETUNE SHORT (30sec.)

or RETUNE LONG (90sec.),

the radio start to retune to next

same PI station.

- TA ALARM mode:

When TP information gets lost at the

current station beeps will be heard.

b) PI SOUND or PI MUTE

In some countries, there is a possibility

of having 2 different stations with same

frequencies but different PI.

If PI SOUND is selected, radio will

switch to the new PI station for few

seconds before switch back to current

PI station.

If PI MUTE is selected, radio will mute

when a new PI station is received.

c) RETUNE L or RETUNE S

When PI information is not caught for

retune time, the radio start to retune to

next same PI station.

- RETUNE L mode:

Retune time selected as 90 seconds.

- RETUNE S mode:

Retune time selected as 30 seconds.

d) MASK DPI or MASK ALL

- MASK DPI mode:

Masked only the AF which has

different PI.

- MASK ALL mode:

Masked the AF which has different

PI and any other interfering non PI

station which having the same

transmitting frequency.

Preset number PTY MUSIC group

1 POP M, ROCK M

2 EASY M, LIGHT M

3 CLASSICS, OTHER M

4 JAZZ, COUNTRY

5 NATION M, OLDIES

6 FOLK M

Preset number PTY SPEECH group

1 NEWS, AFFAIRS, INFO

2 SPORT, EDUCATE,

DRAMA

3 CULTURE, SCIENCE,

VARIED

4 WEATHER, FINANCE,

CHILDREN

5 SOCIAL, RELIGION,

PHONE IN

6 TRAVEL, LEISURE,

DOCUMENT

PTYmusic group PTY speech group PTYoff

Siemens VDO - DV1805 DFU.book Page 12 Thursday, October 27, 2005 1:26 PM

English

CD/MP3 OPERATION

This CD player is suitable for 12cm

disc only, do not use 8cm or irregular

shaped CD.

On top of the usual CD audio disc

playback, you are able to listen to

compressed music file that conform to:

• MPEG1/2 & 2.5 layer 3 at bit rate

from 64kbps to 320kbps or Variable

Bit Rate (VBR).

• Sampling frequency 16/22.05/24/32/

44.1/48KHz.

ID3 Tag version 1 and 2 are both

supported.

SELECT TRACKS

During CD operation, press button

(10) or button (11) to advance or

reverse to the previous track. Press

(13) or (14) button to advance 5 tracks

up (CD) or reverse 10 track (MP3) track

number shows on display.

During CD/MP3 operation, hold

Button (10) or button (11) to fast

forward or fast reverse.

CD/MP3 play starts from when you

release the button.

PAUSE PLAYING

Press button (16) in headunit or (12) in

remote control to pause CD player, Press

it again to resume play.

REPEAT THE SAME TRACK (for CD)

During CD operation, press RPT button

(20) in headunit or RPT (2) in remote

control to repeat the same track. Press

again to stop repeat.

Repeat function (for MP3)

Short press RPT button (20) on headunit

or long press button (2) on remote control

activate the repeat function.

a) When folder is turn on:

Press one time - folder repeat (repeat

songs in the same folder)

Press second time - repeat ONE track

(current track)

Third Press - repeat off

b) When folder is turn off:

Press one time - repeat one track

press second time - repeat off.

SCAN TRACKS

During CD operation, press SCAN (19) in

headunit or SCAN (2) in remote control to

play first several seconds of each track of

the current disc. Press again to stop intro

and listen to track.

PLAY TRACKS IN RANDOM

During CD operation, press RND (21) in

headunit or RND (2) in remote control to

play all tracks on CD in random order.

Press again to cancel the function. (For

MP3, Random function only for tracks

within the same folder)

EJECT

Press button (15) to stop CD playing and

eject the disc from the disc slot (5).

Playing a CD-R/RW

Depending on the type of CD-R/RW CD,

surface condition of the disc, as well as

the performance and condition of the

CD writer, certain CD-R/RW CD may not

function properly on this unit.

Playing a copy protected non

conforming audio CD

Due to use of copy protection schemes of

some audio CDs which are non

conformance to international audio CDs

standards (Red Book), these type of copy

protected disc(s) may not play on this unit.

Notes on MP3

- The unit cannot read an MP3 file that

has a file extension other than “MP3”.

- The unit can play up to maximum

250 tracks and support maximum

50 directories per disc.

- The unit may not play the first tracks

in the order of track number of in the

order that you wrote them to the disc.

- The unit plays only the first session

if the disc contains both CD audio

tracks and MP3 files.

- When playing a disc of below 64kbps

or variable Bit Rate (VBR), the elapsed

playing time in the display window may

not be correct.

Siemens VDO - DV1805 DFU.book Page 13 Thursday, October 27, 2005 1:26 PM

- To display up to 28 characters for a

track name or artist’s name, ID3TAG

version 1.1 is required. Characters

other than uppercase/lowercase

letters (“Aa to Zz”) and underscore

(“_”) may not be displayed.

- To enjoy high quality sound, we

recommended converting to MP3 files

with a sampling frequency of 44.1kHz

and a fixed bit rate of 128kbs.

- Make sure that a CD-R/RW is

formatted as a data disc and NOT as

an audio disc.

- mp3 files are not compatible with

packet write data transfer.

MP3 Playback with OSD screen

When a disc with MP3 files is inserted, the

MP3/JPG folder screen will appear. Each

folder and file will be shown (the order

may be different than that on your PC).

Navigate the files and folders using the

navigation arrow keys, and select a file or

folder to be played by using the MENU

button (7) or the headunit or (15) on

remote control.

DVD/VCD OPERATION

DVD/VCD PLAY BACK

Video CDs with PBC

(playback control)

Video CDs with PBC can be played with

or without a menu:

- Press the MENU button to select

between playback with or

without PBC.

Pause (still picture)

- Long press the button (16) in

headunit or (12) in remote control

during playback. Press the button

(12) once again to resume normal

playback.

Fast forward/reverse

- Long Press the button (10) or (6)

in remote control or button (11) in

headunit or button (6) in remote control

button during playback.

- Each time the button is pressed,

the speed of fast forward/reverse

changes as follows:

Normal - >2x - >4x - >6x - >8x

Skipping chapters/tracks

- Press the button to jump to the

next chapter (DVD) or track (VCD).

- Press the button to jump to

the previous chapter (DVD) or

track (VCD).

Note:

- For some VCD2.0 discs

(PBC playback control), the /

buttons may not work.

Slow forward/reverse

- Short press the SLOW button (12) in

remote control during playback.

- Each time the button is pressed, the

speed of slow forward/reverse

changes as follows:

Normal - >2x - >4x - >6x - >8x

Note: SLOW Reverse does not work in

VCD MODE.

Note:

- The headunit cannot play disc

recorded on DVD-RW and DVD+RW

BASIC OPERATION

Repeating chapters/tracks

Press the REPEAT button (20) in

headunit or (2) in remote control once,

or more than once to select the REPEAT

mode as followes.

DVD:

CHAPTER REPEAT ON:

The current chapter is repeated.

TITLE REPEAT ON: The current title is

repeated.

REPEAT OFF: The repeat function is

switched off.

VCD

REP - ONE: The current track is repeated.

REP - ALL: All tracks of the inserted disc

are repeated.

(available only when PBC is OFF)

Siemens VDO - DV1805 DFU.book Page 14 Thursday, October 27, 2005 1:26 PM

English

OSD (ON SCREEN DISPLAY)

Time displays

Press the DISP button (8) in headunit or

(10) in remote control during playback to

display different time information on the

screen of the disc that is playing.

Example:

DVD:

- Press DISP once:

The following information is shown on the

screen:

- current title number and total number

of titles,

- current chapter number and total

number of chapters, and elapsed

total time. Press DISP again.

Press DISP for the third time:

Press DISP for the fourth time:

Press DISP for the fifth time:

The message on the screen will be

cleared.

VCD

Each time the DISP button is pressed,

the time displayed changes in the

following order:

- SINGLE ELAPSED (track)

- SINGLE REMAIN (track)

- Total ELAPSED (Only when PBC

is off)

- Total REMAIN (only when PBC is off)

- Clear message on screen.

MP3 (with Folder ON)

Each time the DISP button is pressed,

the time displayed changed in the

following order:

- Single ELAPSED

- Single REMAIN

- Clear message on screen

MP3 (NO Folder)

Each time the DISP button is pressed,

the time display changed in the

following order:

- Single ELAPSED

- Single REMAIN

- Clear message in screen.

Each time the DISP button is pressed,

the time display changed in the

following order:

- Single ELAPSED

- Single REMAIN

- Total ELAPSED

- Total REMAIN

- Clear message in screen.

OSD ADVANCED OPERATION

FOR MP3

Make sure that the MP3 files have file

format designation of mp3. Two different

modes of MP3 playback are available:

- FOLDER

- NO FOLDER

The playback mode can be set in the INIT

menu under.

PREFERENCES WITH FOLDER ON

In this mode the display shows all the

MP3 folders of the disc on the left and the

file names of the folder currently opened

on the right.

In STOP mode:

- Use the and buttons to select

between the left and right column.

- Use the and buttons to select the

desired item or folder.

TITLE 02/05 CHAPTER 01/27

01:14:39

TITLE REMAIN

01:14:39

CHAPTE RELAPSED

00:12:24

CHAPTER REMAIN

01:14:39

Siemens VDO - DV1805 DFU.book Page 15 Thursday, October 27, 2005 1:26 PM

- Press the ENTER button to playback

the selected item.

The screen shows:

Notes:

The FOLDER can only be selected in

STOP mode. During playback, the screen

will display the MP3-ID3 tags.

When the NO FOLDER function is set to

“No Folders”, only the track number and

the elapsed time for the current file are

displayed on the screen. All the tracks of

the MP3 CD inserted are played

sequentially.

OSD ADVANCED OPERATION

(For JPEG File)

JPEG PLAYBACK with FOLDER ON

The DVD player supports the display of

JPEG images.

Ensure that the JPEG images have a file

format designation .jpg

JPEG image CD playback

- Insert a disc with JPEG images in

the player

- The MP3/JPEG menu appears on the

display as follows:

In STOP mode:

- You can switch between the left and

right-hand columns using the and

buttons. You can select the desired file

or the desired directory using the

and buttons.

- Press the ENTER or button to start

a slide show, beginning with the

selected file.

- All the images in the current directory

are displayed in sequence for approx.

5 seconds each.

- Press the button in order to pause

or resume the slide show.

For the same folder, you can press to

go to the next image.

In PLAY mode:

To start the slide show of a particular

JPEG file from the selected folder, enter

the number which appears on the right

side of the file in the MP3/JPEG menu.

Using the remote control, key in the file

number and press ENTER button.

JPEG PLAYBACK with “NO FOLDER”

Press to select the next JPEG file.

Press to select the previous JPEG file.

COLOR / BRIGHTNESS / CONTRAST

SETTING

MP3

00 : 00 : 25

MP3/JPG MENU

MP3

REPEAT OFF

PLAY MODE :

OU_DE_YANG_

OU DE YANG_

OU DE YANG

OCEAN_OU

DISC#5

ROOT

UE- 2004 VERSION - OCEAN

00:00:25

MP3 TRACK : 1 / 20

SINGLE ELAPSED

NORMAL PLAY

ROOT

REPEAT OFF

MP3/JPG MENU

MP3

DSC 04050005

DSC 04050004

DSC 04050003

DSC 04050002

DSC 04050001

8 COL

Siemens VDO - DV1805 DFU.book Page 16 Thursday, October 27, 2005 1:26 PM

English

To adjust the colour, contrast and

brightness of the headunit, do the

following:

- In DVD mode, press STOP button (17)

in headunit or STOP button (4) in

remote control.

- Press / in remote control to adjust

desired COLOR setting of DVD output.

- Press ANGLE (19) in remote control

to adjust the DVD output of

desired CONTRAST and

BRIGHTNESS setting.

INIT SETTINGS / INIT MENU

Main page In STOP mode:

- Press the INIT button.

- The initial INIT menu is displayed.

- Select the preferred item by using the

/ buttons.

- Press the ENTER button to confirm

your selection.

The following options are available:

• GENERAL SET-UP

This includes TV display. For details

please refer to the General setup menu.

• SPEAKER SET-UP

This changes the audio output from

DOWNMIX to 2 channel mode. Please

refer to Speaker set-up menu.

• AUDIO SET-UP

This selects all other AUDIO functions.

Please refer to Audio set-up menu.

• PREFERENCES

This configures the system. For details

please refer to Preferences set-up menu

General set-up menu.

GENERAL SETUP

TV DISPLAY

This is to select the appropriate TV aspect

(4:3 or 16:9) according to the connected

TV set.

• NORMAL/LB (For 4:3 Viewing)

Played back in letterbox style.

(If connected to a wide-screen video

source, black bands appear at top and

bottom of the screen.)

• NORMAL/PS (For 4:3 TV)

Played back in the PAN & SCAN style.

(If connected to wide-screen TV, the left

and right edges are cut off.)

•WIDE (For 16:9 Viewing)

Select when a wide-screen video source

is connected.

TV TYPE

This player can play discs recorded in

either PAL or NTSC format.

- Select MULTI format, if the connected

TV supports PAL and NTSC.

- Select NTSC format, if the connected

TV supports NTSC.

- Select PAL format, if the connected TV

supports PAL.

PIC MODE

This is to set the picture process mode

• AUTO: Process according to

the information embedded in the

bitstream itself.

• FILM: Suitable for film or progressive

source.

• VIDEO: Flickerless, ignore the

progressive/interlace info from the

GENERAL SETUP

INIT MENU - - MAIN PAGE

SPEAKER SETUP

AUDIO SETUP

PREFERENCES

EXIT SETUP

GENERAL SETUP

- - GENERAL PAGE - -

GENERAL SETUP

TV DISPLAY

TV TYPE

PIC MODE

ANGLE MARK

OSD LANG

CAPTIONS

MAIN PAGE

NORMAL/PS

NORMAL/LB

WIDE

Siemens VDO - DV1805 DFU.book Page 17 Thursday, October 27, 2005 1:26 PM

bitstream and assume interlace at

all times.

• SMART: Same as AUTO mode,

usually be used for progressive and

interlaced material with limited motion.

• SSMART: motion adaptive

deinterlacing is used only for pictures

marked as interlaced but not for

pictures marked as progressive.

ANGLE MARK

- Select ON, if you want to display the

angle mark “ ” when a multi-angle

DVD disc is playing.

OSD LANG

- Select the desired language for the

On-Screen Display.

CAPTIONS

- Activate the CAPTIONS feature by

selecting ON.

SPEAKER SET-UP MENU

DOWNMIX

This is to select the Dolby AC3 5.1

Downmix mode for the analog output.

• If you select LT/RT, the Dolby Digital

signal is converted to a Dolby

Surround signal.

• If you select STEREO, only left and

right channels are decoded.

AUDIO-SETUP

OP MODE

The operating mode for the Dolby Digital

decoder cannot be configured. The mode

is always set to LINE OUT.

- - SPEAKER SETUP PAGE - -

LOUD SPEAKERS SETUP

DOWNMIX

MAIN PAGE

LT / RT

STEREO

- - AUDIO SETUP - -

AUDIO RELATEO

OP MODE

DUAL MONO

D R C

MAIN PAGE

Siemens VDO - DV1805 DFU.book Page 18 Thursday, October 27, 2005 1:26 PM

English

DUAL MONO

- Select the desired Dual mono mode

for 1+1 coded Dolby Digital programs.

• STEREO: Stereo-reproduction 1+1

program. CH1 for left channel, CH2,

for right channel.

• CH1 MONO: CH1 Mono-reproduction.

CH1 channel in both Left/Right output.

• CH2 MONO: CH2 Mono-reproduction.

CH2 channel in both Left/Right output.

• MIX MONO: Mix mono-reproduction.

CH1+CH2 in both Left/Right output.

DRC - Dynamic range Control

- Select DRC to adjust the dynamic

range of a Dolby Digital encoded

program. There are 8 steps between

off and full compression.

PREFERENCE SET UP

AUDIO

- Select the initial audio soundtrack

language you prefer.

SUBTITLE

- Select the initial subtitle language

you prefer.

DISC MENU

- Select the initial disc menu language

you prefer.

PARENTAL

- Select the desired parental guidance

level from the list. The factory default

password for changing the parental

guidance is 3308.

PASSWORD

- Select CHANGE to change the factory

set password for parental control. Key

in the initial factory password of 3308.

Then key in a new 4 digit password.

Confirm the new password by

reentering it.

MP3/JPEG MENU

This is used to set the display mode for

MP3 playback.

- Select NO FOLDERS to play MP3 files

without folder/file display.

- Select FOLDERS to show the disc

contents in folder/file style.

DEFAULTS

- Select RESET to return the player to

the factory defaults.

SPECIAL FEATURE FUNCTIONS

Hands Free Function

You can connect our hands-free

phone kit (available separately) via the

connector D. See mounting and

connecting instructions for the

hands-free kit.

Select option “HFREE LO” or the “HFREE

HI” in the SETUP mode to automatically

interrupt the set’s sound output when

receiving or making a call.

Note:

Depends on the handphone use to test

the matching of “HFREE LO” or “HFREE

HI” to ensure hands free function operate

properly.

TELEPHONE MUTE

If user does not want the telephone sound

output via car speakers, but want to mute

the set’s sound when receiving or making

a phone call, do the following:

- Connect telephone car kit mute signal

to set’s pink wire (for telephone high)

or grey wire (for telephone low).

- Select uption “HFREEMUT” in

SETUP mode.

JAPANESE

SET PREFERENCES

AUDIO

SUBTITLE

DISC MENU

PARENTAL

MP3/JPEG MENU

PASSWORD

DEFAULTS

ENGLISH

FRENCH

SPANISH

CHINESE

ITALIAN

GERMAN

- - PREFERENCES PAGE - -

Siemens VDO - DV1805 DFU.book Page 19 Thursday, October 27, 2005 1:26 PM

INFRARED REMOTE CONTROL

Infrared remote control is included in

this set.

• Preparing the Remote Control

Inserting the Batteries

1. Open the battery compartment

cover.

2. Insert the new batteries. Make sure

that the positive and negative

terminals of the batteries are

oriented indicated.

3. Close the cover.

Battery: AAA size.

• Using the Remote Control

Face the remote control towards the

player front face IR mark (remote

control signal receiver).

Operation angle: About ±30 degree in

each the direction of the front of the IR

mark.

CLOCK FUNCTION

You can select either manual setting or

automatic update of the clock via RDS

Radio signal.

- Manual clock

Go to SETUP mode,

select “CLOCK ON”

Note:

You can select 12 or 24 hour clock

display.

- RDS clock (auto update)

Go to SETUP mode,

select “RDS CLOCK”

Note:

The transmitted time via RDS can

be incorrect.

LINE OUT

You can connect a 2 channels power

amplifier to this set with the RCA cable.

- connect red socket to right channel.

- connect white socket to left channel.

AUX IN

You can connect the audio output of

auxiliary equipment to the headunit via

RCA cables.

- connect red socket to right channel.

- connect white socket to left channel.

Go to SETUP mode, turn ON the Aux-In

Select the SRC button (12) to Aux-In.

SMART MODE FUNCTION

SMART mode gives you the great

pleasure of listening to radio from front

speakers, and at the same time playing

the disc source (CD/MP3/VCD/DVD) via

Audio/Video RCA output jacks.

In DVD MODE, long press SMART button

on the unit or SMART button on the

remote control shortly during disc

playback to activate SMART MODE

function. “SMART” appears on the display

of the DVD unit. When press SOURCE

button to switch to radio or AV IN mode,

the front speakers will output the

corresponding radio audio signal or audio

signal of the AV source and the rear

speaks will be muted. In any mode (radio

or AV IN), the DVD disc is playing the

video and audio out jacks output the video

signal of DVD all the while.

Note:

SMART mode can only be turned ON/

OFF in disc-mode.

RESET

Should the radio or CD audio/MP3/VCD/

DVD do not function properly. Press the

RESET button (25) to re-innitialise the

headunit to factory default setting.

Headunit should get back to correct

function.

Siemens VDO - DV1805 DFU.book Page 20 Thursday, October 27, 2005 1:26 PM

Page is loading ...

VDO Dayton DV 1805 MP3 User manual

Brand: VDO Dayton

Model: DV 1805 MP3

Category: Car media receivers

Type: User manual

Download PDF

report

VDO Dayton DV 1805 MP3 User manual

VDO Dayton DV 1805 MP3 User manual

Related papers

Other documents