3-098-549-12(1)
Digital Video Camera Recorder
Operating Guide
DCR-SR32E/SR33E/SR42E/SR52E/SR62E/SR72E/
SR82E/SR190E/SR200E/SR290E/SR300E
© 2007 Sony Corporation
For details on the advanced operations, please refer
to “Handycam Handbook” (PDF).
2
Before operating the unit, please read this
manual thoroughly, and retain it for future
reference.
To reduce fire or shock hazard, do not
expose the unit to rain or moisture.
Replace the battery with the specified
type only. Otherwise, fire or injury may
result.
A moulded plug complying with BS1363 is
fitted to this equipment for your safety and
convenience.
Should the fuse in the plug supplied need to
be replaced, a fuse of the same rating as the
supplied one and approved by ASTA or BSI
to BS1362 (i.e., marked with or mark)
must be used. If the plug supplied with this
equipment has a detachable fuse cover, be
sure to attach the fuse cover after you change
the fuse. Never use the plug without the fuse
cover.
If you should lose the fuse cover, please
contact your nearest Sony service station.
ATTENTION
The electromagnetic fields at the specific
frequencies may influence the picture and sound of
this unit.
This product has been tested and found compliant
with the limits set out in the EMC Directive for
using connection cables shorter than 3 meters. (9.8
feet)
Disposal of Old Electrical &
Electronic Equipment
(Applicable in the European
Union and other European
countries with separate
collection systems)
This symbol on the product or on its
packaging indicates that this product shall
not be treated as household waste. Instead it
shall be handed over to the applicable
collection point for the recycling of electrical
and electronic equipment.
By ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise be
caused by inappropriate waste handling of
this product. The recycling of materials will
help to conserve natural resources.
For more detailed information about
recycling of this product, please contact your
local Civic Office, your household waste
disposal service or the shop where you
purchased the product.
Applicable Accessories: Remote
Commander (DCR-SR52E/SR62E/SR72E/
SR82E/SR190E/SR200E/SR290E/
SR300E)
Notice
If static electricity or electromagnetism causes data
transfer to discontinue midway (fail), restart the
application or disconnect and connect the USB
cable again.
Read this first
WARNING
CAUTION
Notice for customers in the
United Kingdom
FOR CUSTOMERS IN EUROPE
3
• The camcorder is not dustproofed, dripproofed or
waterproofed. See “Precautions” (p.30).
• To prevent the hard disk from being broken or
recorded images from being lost, do not do the
following when either of the respective lamps of
the POWER switch (p.9) or the access lamp* is on:
–to remove the battery pack or AC Adaptor from
the camcorder.
– to apply mechanical shock or vibration to the
camcorder.
On recording
• Before starting to record, test the recording
function to make sure the image and sound are
recorded without any problems.
• Compensation for the contents of recordings
cannot be provided, even if recording or playback
is not possible due to a malfunction of the
camcorder, recording media, etc.
• TV color systems differ depending on the
countries/regions. To view your recordings on a
TV, you need a PAL system-based TV.
• Television programs, films, video tapes, and other
materials may be copyrighted. Unauthorized
recording of such materials may be contrary to
the copyright laws.
Save all your recorded image data
• To prevent your image data from being lost, save
all your recorded images on external media. It is
recommended that you save the image data on a
disc such as DVD-R using your computer*. Also,
you can save your image data using a VCR, or a
DVD/HDD recorder*.
• It is recommended that you save your image data
periodically, after recording.
Do not apply shock or vibration to your
camcorder
• The hard disk of the camcorder may not be
recognized, or recording or playback may not be
possible.
On the drop sensor
• To protect the internal hard disk from the shock
by dropping, the camcorder has the drop sensor
function*. When a drop occurs, or under a non-
gravity condition, the block noise to protect the
camcorder may also be recorded. If the drop
sensor catches a drop repeatedly, recording/play
back may be stopped.
Note on operational temperatures
• When the temperature of the camcorder becomes
extremely high or extremely low, you may not be
able to record or play back on the camcorder, due
to the protection features of the camcorder being
activated in such situations. In this case, an
indicator appears on the LCD screen (p.28).
When the camcorder is connected to a
computer
• Do not try to format the hard disk of the camcorder
using a computer. If you do so, your camcorder
may not operate correctly.
Note on using the camcorder at high
altitudes
• Do not turn on the camcorder in a low-pressure
area, where the altitude is more than 3,000 meters
(9,800 feet). Doing so may damage the hard disk
drive of your camcorder.
Note on disposal/transfer
• If you perform [ FORMAT]* or formatting the
hard disk of the camcorder, you may not delete
data from the hard disk completely. When you
transfer the camcorder, it is recommended that
you perform [ EMPTY]* to prevent the
recovery of your data.
In addition to the above, when you dispose of the
camcorder, it is recommended that you destroy
the actual body of the camcorder.
About language setting
• The on-screen displays in each local language are
used for illustrating the operating procedures.
Change the screen language before using your
camcorder if necessary (p.9).
About this manual
• The LCD screens and indicators shown in this
manual were taken with a digital still camera, and
may look different from what you actually see.
• Design and specifications of recording media and
other accessories are subject to change without
notice.
• Unless otherwise specially indicated, illustrations
in this manual are based on DCR-SR300E.
• The screenshots are from Windows XP. The
scenes may vary depending on the operating
system of the computer.
* Refer to “Handycam Handbook” (PDF).
Notes on use
4
Table of Contents
Read this first ............................................................................................ 2
Notes on use............................................................................................. 3
Step 1: Checking supplied items............................................................... 5
Step 2: Charging the battery pack ............................................................ 7
Step 3: Turning the power on, and setting the date and time ................... 9
Changing the language setting ..................................................................... 9
Step 4: Preparing for recording............................................................... 10
Recording................................................................................................ 11
Playback ................................................................................................. 13
Parts and functions used for the camcorder ........................................... 15
Indicators displayed during recording/playback...................................... 18
Saving images ........................................................................................ 20
Deleting images ...................................................................................... 20
Playing the image on a TV...................................................................... 21
Performing with a computer.................................................................... 22
Performing various functions - “ HOME” and “ OPTION” .............. 24
Troubleshooting ...................................................................................... 27
Warning indicators .................................................................................. 28
Precautions............................................................................................. 30
Specifications..........................................................................................31
Getting Started
Recording/Playback
Troubleshooting
Additional Information
5
Getting Started
Make sure that you have the following items
supplied with your camcorder.
The number in the parentheses indicates the
number of that item supplied.
AC Adaptor (1) (p.7)
Mains lead (1) (p.7)
Handycam Station (1) (p.7)
A/V connecting cable (1) (p.21)
USB cable (1) (p.23)
Wireless Remote Commander (1)
(except for DCR-SR32E/SR33E/SR42E)
A button-type lithium battery is already installed.
Rechargeable battery pack
NP-FH40 (1) (p.7) (DCR-SR32E/SR33E/
SR42E/SR52E/SR62E/SR72E/SR82E)
NP-FH60 (1) (p.7) (DCR-SR190E/SR200E/
SR290E/SR300E)
21-pin adaptor (1)
For the models with the mark printed on their
bottom surfaces only.
CD-ROM “Handycam Application
Software” (1) (p.22)
– Picture Motion Browser (Software)
– Handycam Handbook (PDF)
“Operating Guide” (This manual) (1)
Step 1: Checking supplied items
6
Using the Remote Commander for the
first time
Remove the insulation sheet before using the
Remote Commander.
To change the battery of the Remote
Commander
1 While pressing on the tab, inset your
fingernail into the slit to pull out the battery
case.
2 Place a new battery with the + side facing up.
3 Insert the battery case back into the Remote
Commander until it clicks.
• When the lithium battery becomes weak, the
operating distance of the Remote Commander
may shorten, or the Remote Commander may not
function properly. In this case, replace the battery
with a Sony CR2025 lithium battery. Use of
another battery may present a risk of fire or
explosion.
On the Remote Commander
(except for DCR-SR32E/SR33E/
SR42E)
WARNING
Battery may explode if mistreated. Do not
recharge, disassemble or dispose of in fire.
Insulation sheet
Tab
7
Getting Started
You can charge the “InfoLITHIUM”
battery pack (H series) after attaching
it to your camcorder.
• Your camcorder operates only with an
“InfoLITHIUM” battery pack (H series).
1 Attach the battery pack by sliding
it in the direction of the arrow until
it clicks.
2 Turn the POWER switch in the
direction of the arrow to OFF (CHG)
(The default setting).
3 Connect the AC Adaptor to the DC
IN jack on the Handycam Station.
Be sure that the v mark on the DC plug
is facing up.
4 Connect the mains lead to the AC
Adaptor and the wall socket.
5 Set the camcorder onto the
Handycam Station securely.
The CHG (charge) lamp lights up and
charging starts. The CHG (charge) lamp
turns off when the battery pack is fully
charged. Remove the camcorder from the
Handycam Station.
To remove the battery pack
Turn the POWER switch to OFF (CHG).
Slide the BATT (battery) release lever and
remove the battery pack.
• When you remove the battery pack or the AC
Adaptor, make sure that the (Movie) lamp/
(Still) lamp (p.9) is turned off.
Step 2: Charging the battery pack
POWER
switch
CHG
lamp
DC IN jack
DC plug
AC Adaptor
Mains lead
To t h e
wall socket
Battery pack
BATT (battery)
release lever
8
To charge the battery pack using only
the AC Adaptor
Turn the POWER switch to OFF (CHG), then
connect the AC Adaptor directly to the DC
IN jack on the camcorder.
Charging time:
Approximate time (min.) required when you
fully charge a completely exhausted battery
pack.
Recording/Playback time:
Approximate time (min.) available when you
use a fully charged battery pack.
NP-FH40:
(Unit:min.)
NP-FH60: (Unit:min.)
*
1
When [REC MODE] is set to [SP].
*
2
When the LCD backlight turns on.
*
3
When the LCD backlight turns off.
*
4
Typical recording time shows the time when you
repeat recording start/stop, turning the power on/
off and zooming.
On the battery pack
• Before changing the battery pack, turn the
POWER switch to OFF (CHG) and turn off the
(Movie) lamp/ (Still) lamp (p.9).
• The power will not be supplied from the battery
as long as the AC Adaptor is connected to the DC
IN jack of your camcorder or the Handycam
Station, even when the mains lead is disconnected
from the wall socket.
On the charging/recording/playback time
• Times measured when using the camcorder at
25°C (77°F) (10°C to 30°C (50°F to 86°F) is
recommended).
• The available recording and playback time will
be shorter when you use your camcorder in low
temperatures.
• The available recording and playback time will
be shorter depending on the conditions under
which you use your camcorder.
On the AC Adaptor
• Use the nearby wall socket when using the AC
Adaptor. Disconnect the AC Adaptor from the
wall socket immediately if any malfunction
occurs while using your camcorder.
• Do not use the AC Adaptor placed in a narrow
space, such as between a wall and furniture.
• Do not short-circuit the DC plug of the AC
Adaptor or battery terminal with any metallic
objects. This may cause a malfunction.
• Even if your camcorder is turned off, AC power
(mains) is still supplied to it while connected to
the wall socket via the AC Adaptor.
Available running time for the
supplied battery pack
DCR-SR32E/
SR33E/
SR42E
DCR-SR52E/
SR62E/
SR72E/SR82E
Charging time
125 125
Recording time*
1
Continuous
recording time
105
90*
2
100*
3
Typical
recording time
*
4
50
45*
2
50*
3
Playback time
120 110*
2
DC IN jack
Open the jack
cover
DC plug
POWER
switch
DCR-SR190E/
SR200E
DCR-SR290E/
SR300E
Charging time
135 135
Recording time*
1
Continuous
recording time
115*
2
125*
3
100*
2
105*
3
Typical
recording time
*
4
55*
2
60*
3
50*
2
50*
3
Playback time*
2
165 160
9
Getting Started
1 While pressing the green button,
turn the POWER switch repeatedly
in the direction of the arrow until
the respective lamp lights up.
When you record or play back an image,
turn the POWER switch in the direction
of the arrow repeatedly until the
respective lamp lights up.
(Movie): To record movies
(Still): To record still images
• When you turn on (Still) lamp, the screen
aspect ratio is changed to 4:3 automatically.
2 Select the desired geographical
area with
v/V, then touch [NEXT].
3 Set [SUMMERTIME], [Y] (year), [M]
(month), [D] (day), hour and
minute.
The clock starts.
• The date and time does not appear during
recording, but they are automatically recorded on
the hard disc, and can be displayed during
playback.
To reset the date and time
Touch (HOME) t (SETTINGS) t
[CLOCK/ LANG] t [CLOCK SET], and
set the date and time.
You can change the on-screen displays to
show messages in a specified language.
Touch (HOME) t (SETTINGS) t
[CLOCK/ LANG] t [ LANGUAGE
SET], then select the desired language.
Step 3: Turning the power on, and setting the date
and time
When using the
camcorder for the
first time, the
[CLOCK SET]
screen appears on
the LCD screen.
Touch the button on the
LCD screen.
POWER switch
Changing the language setting
10
1 Adjust the LCD panel.
Open the LCD panel 90 degrees to the
camcorder (1), then rotate it to the best
angle to record or play (2).
2 Turn the POWER switch to turn on
your camcorder.
3 Press WIDE SELECT repeatedly to
select the desired screen aspect
ratio (except for DCR-SR32E/
SR33E/SR42E).
4 Fasten the grip belt and hold your
camcorder correctly.
Step 4: Preparing for recording
2 180 degrees (max.)
2 90 degrees
(max.)
1 90 degrees
to the
camcorder
16:9 (wide)
4:3
POWER
switch
* Except for DCR-SR32E/SR33E/SR42E.
11
Recording/Playback
1 Slide the lens cover switch to open (DCR-SR32E/SR33E/SR42E/SR52E/SR62E/
SR72E/SR82E).
• For DCR-SR190E/SR200E/SR290E/SR300E, the lens cover opens and closes automatically.
2 Turn the POWER switch until the respective lamp lights up.
Press the green button only when the POWER switch is in the OFF (CHG) position.
• (Movie): To record movies
• (Still): To record still images
3 Start recording.
Recording
Movies Still Images
Press START/STOP A (or B).
To stop recording, press START/STOP
again.
Press PHOTO lightly to adjust the
focus A (a beep sounds), then press
it fully B (a shutter click sounds).
When disappears, the image has been
recorded.
• Still images are recorded on the hard disk in the
default setting.
START/STOP B
Lens cover switch
(DCR-SR32E/SR33E/
SR42E/SR52E/SR62E/
SR72E/SR82E)
Flashing t Lights up
POWER switch
START/STOP A
[STBY] t [REC]
EASY button
PHOTO
12
• You can check the free hard disk space by
touching (HOME) t (MANAGE
HDD/MEMORY) t [ INFO].
• If the ACCESS lamp is lit or flashing after
recording is finished, it means data is still being
written onto the hard disk or “Memory Stick
Duo.” Do not apply shock or vibration to your
camcorder, and do not remove the battery or AC
Adaptor.
• You can capture up to 3 still images by pressing
PHOTO during movie recording (DCR-SR190E/
SR200E/SR290E/SR300E).
• The maximum continuous recordable time is
approximately 13 hours.
• When a movie file exceeds 2 GB, the next movie
file is created automatically.
• The maximum recordable time are followings
(with recording mode [SP]);
DCR-SR32E/SR42E/SR52E/SR62E:
approx. 10 hours and 50 minutes
DCR-SR72E/SR82E:
approx. 21 hours and 40 minutes
DCR-SR33E/SR190E/SR200E/SR290E/
SR300E:
approx. 14 hours and 30 minutes
To record still images on a “Memory
Stick Duo”
You can change the recording media of still
images to a “Memory Stick Duo.”
You can use only a “Memory Stick Duo”
marked with or
.
x Inserting/ejecting a “Memory Stick
Duo”
Open the LCD panel, then insert the
“Memory Stick Duo” into the Memory
Stick Duo slot in the right direction until
it clicks.
To eject a “Memory Stick Duo,” open the
LCD panel, lightly push the “Memory
Stick Duo” in once.
• When the ACCESS lamp is lit or flashing, your
camcorder is reading/writing data. Do not shake
or knock your camcorder, turn the power off, eject
the “Memory Stick Duo,” or remove the battery
pack. Otherwise, image data may be damaged.
• If you insert the “Memory Stick Duo” into the slot
in the wrong direction, the “Memory Stick Duo,”
the “Memory Stick Duo” slot, or image data may
be damaged.
• The numbers of recordable still images on the
“Memory Stick Duo” (1GB) are followings (with
the default setting of the image size as shown in
( ));
DCR-SR32E/SR33E/SR42E: 5,900 ([VGA
(0.3M)])
DCR-SR52E/SR62E/SR72E/SR82E: 1,800
([1.0M])
DCR-SR190E/SR200E: 480 ([4.0M])
DCR-SR290E/SR300E: 315 ([6.1M])
• All numbers measured when using a “Memory
Stick Duo” made by Sony Corporation. The
number of recordable images varies depending on
the recording environment.
• The number of recordable images varies
depending on the image quality or the image size.
For details, see “Handycam Handbook” (PDF).
x To change the recording media of
still images
1 Touch (OPTION) t tab t
[STILL MEDIA].
2 Select the media in which you want to
save still images, then touch .
Your camcorder returns to recording
standby mode.
On Easy Handycam operation
By pressing the EASY button, nearly all
settings on the camcorder will be
automatically operated so that you can
perform recording or playing back operation
without detailed settings. During Easy
Handycam operation, appears on the
LCD screen. To cancel Easy Handycam
operation, press EASY again.
• You cannot use some buttons/functions during
Easy Handycam operation.
ACCESS lamp
(“Memory Stick Duo”)
13
Recording/Playback
1 Turn the POWER switch to turn on your camcorder.
2 Press (VIEW IMAGES) A (or B) button.
The VISUAL INDEX screen appears on the LCD screen. (It may take some time to display
the thumbnails.)
3 Start playback.
Playback
Movies Still Images
Touch the tab, and the movie to
be played back.
Touch the , or tab, and the still
image to be played back.
1 Returns to the recording screen
2 Previous 6 images
3 Next 6 images
4 Returns to the recording screen
5 Displays movies
(VIEW IMAGES)
button B
(VIEW IMAGES) button A
6 Displays still images on the hard disk
7 Displays still images on a “Memory Stick Duo”
8 Searches for images by date
9 (OPTION)
POWER switch
Beginning of the
scene/previous
scene
Toggles Play
or Pause as you
touch
Next
scene
Stop (go to the VISUAL
INDEX screen)
Reverse/Forward
Slide show button
Previous/
Next
Go to the VISUAL
INDEX screen
14
To adjust the sound volume of movies
When playing back a movie, touch
(OPTION) t tab t [VOLUME], then
adjust the volume with / .
• When playback from the selected movie reaches
the last movie, the screen returns to the VISUAL
INDEX screen.
• Touch / during pause to play back
movie slowly.
• One touch of / makes the reverse/fast
forward approximately 5 times faster, 2 touches
makes it approximately 10 times faster, 3 touches
makes it approximately 30 times faster, and 4
touches makes it approximately 60 times faster.
• i appears with the image on each of the tab that
was lastly played back/recorded (B for the still
image) last time. When you touch a movie marked
with i, you can play it back from the point you
have stopped previously.
15
Recording/Playback
1 Power zoom lever
To use zoom, move the power zoom lever.
Move the power zoom lever slightly for a
slower zoom. Move it further for a faster
zoom.
2 NIGHTSHOT PLUS switch*
1
To record in dark places, set the
NIGHTSHOT PLUS switch to ON. (
appears.)
6 Built-in microphone
Records sound.
Sound picked up by the built-in microphone
is converted to 5.1ch surround sound and
recorded.*
2
Parts and functions used for the camcorder
Handycam
Station
DCR-SR32E/SR33E/SR42E/
SR52E/SR62E/SR72E/SR82E
DCR-SR190E/SR200E/
SR290E/SR300E
DCR-SR32E/SR33E/SR42E/SR52E/
SR62E/SR72E/SR82E
DCR-SR190E/SR200E/
SR290E/SR300E
Recording
16
7 Remote sensor*
3
Receive the signal from the Remote
Commander.
8 Flash*
2
Flashes when using the flash.
9 LCD screen
To record in mirror mode, open the LCD
screen 90 degrees to the camcorder (1), then
rotate it 180 degrees to the lens side (2).
q; Zoom buttons
Press for zooming in/out.
qa BACK LIGHT button*
4
To adjust the exposure for backlit subjects,
press BACK LIGHT to display .. To cancel
the back light function, press BACK LIGHT
again.
qs DISP/BATT INFO button
You can switch the screen display when you
press while the power is set to on.
When you press while the power is set to OFF
(CHG), you can check the remaining battery.
qd EASY button
See page 12.
qf (flash) button*
2
You can select the settings for the flash.
qg Shoulder belt hook
Attach the shoulder belt (optional).
qh NIGHTSHOT switch*
2
To record in dark places, set the
NIGHTSHOT switch to ON. ( appears.)
qk Tripod receptacle (Bottom surface)
Attach the tripod (optional: the length of the
screw must be less than 5.5 mm (7/32 in.)) to
the tripod receptacle using a tripod screw.
ql RESET button
To initialize the settings (Reset), press
RESET to initialize all the settings, including
settings for date and time.
1 Power zoom lever
q; Zoom buttons
You can magnify still images from about 1.1
to 5 times the original size (Playback zoom).
• When you touch the screen during playback
zoom, the point you touched will be displayed in
the center of the displayed frame.
qd EASY button
See page 12.
qj Speaker
Sound comes out from the speaker while
playing back.
3 A/V OUT jack
Connect with the A/V connecting cable.
4 REMOTE jack*
3
Connect other optional accessories.
5 Active Interface Shoe *
3
The Active Interface Shoe supplies power to
optional accessories such as a video light, a
flash, or a microphone. The accessory can be
turned on or off as you operate the POWER
switch on your camcorder.
w; DC IN jack
wa Interface connector
Playback
Connecting to other devices
17
Recording/Playback
ws DISC BURN button
Create a DVD by connecting the camcorder
to a computer. For details, see “Handycam
Handbook” (PDF).
wd (USB) jack*
5
Connect with the USB cable.
*
1
DCR-SR32E/SR33E/SR42E/SR52E/SR62E/
SR72E/SR82E
*
2
DCR-SR190E/SR200E/SR290E/SR300E
*
3
Except for DCR-SR32E/SR33E/SR42E
*
4
For DCR-SR32E/SR33E/SR42E, the position of
the buttons differ from the illustration.
*
5
For DCR-SR32E/SR33E/SR52E/SR72E/
SR190E/SR290E: output only.
18
Indicators displayed during recording/playback
Recording movies Recording still images
Viewing movies Viewing still images
1 Recording mode (HQ / SP / LP)
2 HOME button
3 Remaining battery (approx.)
4 Recording status ([STBY] (standby) or
[REC] (recording))
5 Counter (hour/minute/second)
6 OPTION button
7 Dual Rec (DCR-SR190E/SR200E/
SR290E/SR300E)
8 VIEW IMAGES button
9 5.1ch surround recording (DCR-
SR190E/SR200E/SR290E/SR300E)
q; Quality ([FINE] / [STD])
qa Image size
qs Appears while a still image is being
saved.
qd Recording folder
Displays only during the recording media
of still images is a “Memory Stick Duo.”
qf Return button
qg Playback mode
qh Current movie number/Number of total
movies
qj Previous/Next button
qk Video operation buttons
ql Data file name
w; Current still image number/Number of
recorded still images
wa Slide show button
ws Previous/Next button
wd Data file name
wf VISUAL INDEX button
19
Recording/Playback
Following indicators appear during
recording/playback to indicate the settings of
your camcorder.
Upper left
Upper right
Center
Bottom
*
1
DCR-SR190E/SR200E/SR290E/SR300E
*
2
DCR-SR32E/SR33E/SR42E
*
3
DCR-SR52E/SR62E/SR72E/SR82E/SR190E/
SR200E/SR290E/SR300E
*
4
DCR-SR32E/SR33E/SR42E/SR52E/SR62E/
SR72E/SR82E
• The recording date and time is recorded
automatically on the hard disk and “Memory
Stick Duo.” They are not displayed while
recording. However, you can check them as
[DATA CODE] during playback.
Indicators when you made
changes
Indicator Meaning
5.1ch surround recording/
playback*
1
Self-timer recording
Flash
MICREF LEVEL low
WIDE SELECT*
2
WIDE SELECT*
3
Indicator Meaning
FADER
LCD backlight off
Drop sensor off
Drop sensor activated
Indicator Meaning
Slide show set
NightShot plus*
4
NightShot*
1
Super NightShot plus*
4
Super NightShot*
1
Color Slow Shutter
Upper left Upper right
Bottom Center
PictBridge connecting
E
Warning
Indicator Meaning
Picture effect
Digital effect
9 Manual focus
SCENE SELECTION
. Backlight
n White balance
SteadyShot off
EXPOSURE/
SPOT METER
TELE MACRO
ZEBRA*
1
Indicator Meaning
20
Recorded images are stored on the internal
hard disk of your camcorder. Due to the
limited capacity of the internal hard disk,
make sure that you save the image data to
some type of external media such as a
DVD-R or a computer.
You can save the images recorded on the
camcorder as described below.
By using the software on the supplied
CD-ROM, you can save images on a DVD or
the hard disk of a computer. For details, see
“Handycam Handbook” (PDF).
Creating a DVD with One Touch
(One Touch Disc Burn)
You can save images recorded on the
camcorder directly to a DVD with ease.
Saving images on a computer
You can save images recorded on the
camcorder on the hard disk of a computer.
Creating a DVD with selected images
You can save images imported to your
computer on a DVD. You can also edit those
images.
You can dub images to VCR or DVD/HDD
devices. For details, see “Handycam
Handbook” (PDF).
1 On the (HOME MENU), touch
(OTHERS) t [DELETE].
2 Touch [ DELETE].
3 Touch [ DELETE] (movies) or
[ DELETE] (still images),
according to the type of image you
want to delete, then touch the
image to be deleted.
The selected image is marked with .
4 Touch t [YES] t .
To delete all movies or still images at
one time
In step 3, touch [ DELETE ALL] or [
DELETE ALL] t [YES] t [YES] t .
To delete the still images in the
“Memory Stick Duo”
1 In step 2, touch [ DELETE].
2 Touch [ DELETE], then touch the still
image to be deleted.
The selected still image is marked with
.
3 Touch t [YES] t .
• To delete all still images on the “Memory Stick
Duo,” in step 2, touch [ DELETE ALL] t
[YES] t [YES] t .
Saving images
Saving images using a computer
Saving images by connecting
your camcorder to other devices
Deleting images
Deleting the images on the hard
disk
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
