Black Box KVXLC-RMKDUAL Quick start guide

Black Box
Brand
Black Box
Model
KVXLC-RMKDUAL
Category
Rack accessories
Type
Quick start guide

Black Box KVXLC-RMKDUAL is a 19-inch rackmount tray designed to mount up to two KVX Series KVM extenders (transmitters and/or receivers) in a 2-/4-post 19-inch rack or cabinet. The tray is made of durable steel and includes all necessary mounting hardware. The KVXLC-RMKDUAL is a convenient and space-saving solution for mounting KVX Series KVM extenders in a rack environment. It allows you to keep your extenders organized and secure, while also providing easy access to the front panel controls and ports.

Black Box KVXLC-RMKDUAL is a 19-inch rackmount tray designed to mount up to two KVX Series KVM extenders (transmitters and/or receivers) in a 2-/4-post 19-inch rack or cabinet. The tray is made of durable steel and includes all necessary mounting hardware. The KVXLC-RMKDUAL is a convenient and space-saving solution for mounting KVX Series KVM extenders in a rack environment. It allows you to keep your extenders organized and secure, while also providing easy access to the front panel controls and ports.

KVXLC-RMKDUAL
24/7 TECHNICAL SUPPORT AT 877.877.2269 OR VISIT BLACKBOX.COM
QUICK START GUIDE
• (1) 19" RACKMOUNT TRAY
• (4) METAL BRACKETS
• (16) SCREWS FOR MOUNTING BRACKETS TO EXTENDERS AND EXTENDERS TO TRAY
• (4) 10-32 SCREWS FOR MOUNTING TRAY TO RACK
• THIS QUICK START GUIDE
STEP 1: CHECK THE PACKAGE CONTENTS
KVXLC-RMKDUAL PACKAGE CONTENTS
INTRODUCTION
STEP 2: INSTALLING THE EXTENDERS ON THE RACKMOUNT TRAY
1.877.877.2269 BLACKBOX.COM
SAFETY WARNING
INSTALLATION STEPS
STEP 2A: Remove the rackmount tray from the packaging and place it on a secure surface.
NOTE: You will need to use the included screws to complete the installation. Refer to the
illustration shown on the next page.
STEP 2B: To install the bracket to the extender, insert two screws (included) through two
adjacent holes on the bracket into the holes on the side of the extender. Using the second
bracket, repeat this step on the other side of the extender.
STEP 2C: To install the extender/bracket assembly to the rackmount tray, insert two screws
(included) through the two holes on the bottom of the bracket into the holes on the rackmount
tray. Repeat this step on the other side of the extender/bracket assembly.
STEP 2D: If you want to install a second extender on the rackmount tray, repeat Steps 2 and 3.
Use the Rackmount Tray (KVXLC-RMKDUAL) to mount up to (2) KVX Series KVM extenders
(transmitter[s] and/or receiver[s]) in a 2-/4-post 19" rack or cabinet.
Rack loading — Overloading or uneven loading of racks may result in shelf or rack failure, possibl y
damaging the equipment and causing personal injury. Stabilize racks in a permanent locatio n
before loading begins. Do not exceed your rack’s load rating.
The weights of the extenders are as follows:
KVX Series transmitter: 0.82 lb. (0.37 kg)
KVX Series receiver: 0.84 lb. (0.38 kg)
KVX Series Dual-Head transmitter: 1.15 lb. (0.52 kg)
KVX Series Dual-Head receiver: 1.19 lb. (0.54 kg)
KVXLC-RMKDUAL: 0.646 lb. (0.293 kg)
1.877.877.2269 BLACKBOX.COM
STEP 3: INSTALLING THE RACKMOUNT TRAY IN A 19-INCH RACK
INSTALLATION STEPS
STEP 3A: Attach the tray to the 2-/4-post rack/cabinet from the front. Secure the tray to the rack
using two 10-32 screws (four are included) for each rack post.
STEP 3B: Tighten all mounting screws to secure the tray in the rack.
STEP 3C: Repeat for the other side.
STEP 2B
STEP 2B
STEP 2C
STEP 2C
COPYRIGHT 2021. BLACK BOX CORPORATION. ALL RIGHTS RESERVED.
KVXLC-RMKDUAL_QSG_REV2.PDF
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Black Box KVXLC-RMKDUAL Quick start guide

Black Box
Brand
Black Box
Model
KVXLC-RMKDUAL
Category
Rack accessories
Type
Quick start guide

Black Box KVXLC-RMKDUAL is a 19-inch rackmount tray designed to mount up to two KVX Series KVM extenders (transmitters and/or receivers) in a 2-/4-post 19-inch rack or cabinet. The tray is made of durable steel and includes all necessary mounting hardware. The KVXLC-RMKDUAL is a convenient and space-saving solution for mounting KVX Series KVM extenders in a rack environment. It allows you to keep your extenders organized and secure, while also providing easy access to the front panel controls and ports.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents