ADT ZWM Series Wi-Fi and Z-Wave Module Installation guide

ADTZWM Series Wi-Fi® and Z-Wave® Module

Installation and Setup Guide

General Information

The Communication Module allows the Control Panel to communicate with the WTS700 Wireless Keypad and Amazon Alexa via Wi-Fi.

The ADTZWM communications module is intended to provide compatible ADT Control Panels with a Wi-Fi connection as well as

connection with and the ability to control Z-Wave devices. The module connects directly to the Control Panel and is powered via the

Control Panel’s connection. The ADTZWM Series includes models ADTZWM and ADTZWMX.

Compatible Control Panels:

ADT7AIO/ADT5AIO Series - Installation Guide P/N 800-24121 or higher.

ADTHYBWL Series - Installation Guide P/N 800-24125 or higher.

ADT2X16AIO Series – Installation Guide P/N 800-24341 or higher.

NOTE: Control Panel Firmware Release 4.5 or later is required for the ADTZWMX.

Installing the Module in the ADT7AIO/ADT5AIO or ADT2X16AIO Series

Ensure that all electrical power is removed from the control before installing the module. Unplug

the power supply and disconnect the backup battery.

1. Affix the provided FCC/IC label (P/N 800-24286 on

the Control Panel’s case back (refer to Figure 1).

2. If the Control Panel is not powered up proceed to step

5. If the Control Panel is powered up, it must be

powered down as follows:

a. ADT7AIO/ADT5AIO or WTS700 Touchscreen –

At the Advanced screen select “System

Shutdown” and confirm. Wait 30-60 seconds.

b. ADT2X16AIO or WTP100/WLTP100 Touchpad –

Enter Master Code + # +* + 9. Wait 30-60

seconds.

3. Unplug the power supply.

4. Disconnect the battery.

grip-020-V0

HONEYWELL

FCC / IC STATEMENT

800-24167 2/18 Rev A

This device complies with Part 15 of the FCC Rules, and

RSS 210 of IC. Operation is subject to the following two

conditions: (1) This Device may not cause harmful interfer-

ence. (2) This device must accept any interference received,

including interference that may cause undesired operation.

FCC ID: CFS8DL-GRIPAIO7

IC: 573F-GRIPAIO7 IC MODEL: GRIPAIO7

CONTAINS MODULE:

FCC ID: RI7LE910NAV2

IC:5131A-LE910NAV2

CONTAINS MODULE:

FCC ID: RI7LE910NAV2

IC:5131A-LE910NAV2

Figure 1. FCC/IC Label Location

5. Remove the screw securing the rear case to the front

case.

6. Slide the rear case down and separate from the front

case.

7. Remove the communication module access cover.

8. Unplug the power supply (if connected).

9. Secure the module with the provided screw.

10. Re-install the communication module access cover.

11. Connect the battery

12. Install the rear case and secure with the screw.

13. Plug the power supply into a 24-hour, 110VAC

unswitched outlet.

SCREW

grip-011-V0

COVER

SCREW

Figure 2. Installing the ADTZWM Module

Installing the Module in the ADTHYBWL Series

Ensure that all electrical power is removed from the Control Panel before installing the module. Unplug

the power supply and disconnect the backup battery and earth ground.

1. Affix the provided FCC/IC label (ADTZWM, P/N

800-24286) on the ADTHYBWL cabinet (refer to

Figure 3)

2. If the Control Panel is not powered up proceed to

step 5. If the Control Panel is powered up, it must

be powered down as follows:

a. WTP100/WLTP100 Touchpad - Enter Master

Code + # +* + 9. Wait 30-60 seconds.

b. WTS700 Touchscreen – At the Advanced

screen select “System Shutdown” and confirm.

Wait 30-60 seconds.

3. Unplug the power supply.

4. Disconnect the battery and earth ground.

BATT+ BATT -

AUX/BELL_OC LED

RUN LED

IB2/ACTIVE LED

RESERVED LED

TRIGGER 2

12V

GND

TRIGGER 1

BATTERY POWER LED

NOT

USED

ZONE 2

2000

OHMS

EOLR

ZONE 1

USE FOR

2-WIRE SMOKE

DETECTORS

MAXIMUM

NUMBER OF

2-WIRE SMOKE

DETECTORS

ON ZONE 1

IS 16

ZONE 1

2000

OHMS

EOLR

2000

OHMS

EOLR

ZONE 3

2000

OHMS

EOLR

ZONE 4

2000

OHMS

EOLR

ZONE 5

2000

OHMS

EOLR

ZONE 6

2000

OHMS

EOLR

ZONE 7

2000

OHMS

EOLR

ZONE 8

EARTH

GROUND

300-10211

13.5 VDC, 1.8A

POWER

SUPPLY TO

10VAC

UNSWITCHED

OUTLET

(24HR)

DC+

DC -

DC+

DC -

ADTHYBWL-Series - Summary of Connections

800-24129 2/18 Rev.A

RJ-45

CONNECTOR

TAMPER

SWITCH

BLACK

RED

RECHARGEABLE BATTERY

(12V, 7AH)

SEALED LEAD ACID TYPE

SEE

INSTRUCTIONS**

FOR PROPER

GROUNDING

TO INTERNET

CONNECTION

GND

AUX

SLOT 3

GENERAL

SLOT 2

WiFi / ZWAVE

SLOT 1

LTE

8-PIN TRIGGER

CONNECTOR

AC POWER LED

TRIGGER OUTPUT 1: 100mA MAX

TRIGGER OUTPUT 2: 100mA MAX

AUX OUTPUT LED

NOT

USED

24-HR BATTERY

STANDBY REQUIRED

FOR FIRE

INSTALLATIONS.

USE 12V, 7AH

BATTERY FOR

120mA AUX POWER.

SEE INSTRUCTIONS.

BATTERY CAPACITY FOR EMERGENCY

BURGLARY STANDBY USE AT LEAST

4 HRS.

CHARGING VOLTAGE 13.8VDC.

MAXIMUM CHARGING CURRENT

650mA.

SEALED LEAD-ACID TYPE. BATTERY

NORMALLY NEED NOT BE REPLACED

FOR AT LEAST THREE YEARS

TO DETERMINE TOTAL STANDBY LOAD

ON BATTERY, ADD 100mA TO TOTAL OF

AUX. POWER AND REMOTE TOUCHPAD

CURRENTS

WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM. IN ADDITION, THIS

SYSTEM MUST BE CHECKED BY A QUALIFIED TECHNICIAN AT LEAST ONCE EVERY THREE (3) YEARS.

BLACK: TOUCHPAD GND (-) RETURN

YELLOW: TOUCHPAD IB2A

GREEN: TOUCHPAD IB2B

RED: TOUCHPAD POWER (+)

AUX. PWR

OUTPUT

10.5-13.8VDC

200mA MAX.

(120mA MAX.

FOR UL

INSTALLATIONS)

ALL OUTPUTS

ARE POWER

LIMITED.

}

CONNECTION OF

THE FIRE ALARM

SIGNAL TO A FIRE

ALARM HEAD-

QUARTERS OR

CENTRAL STATION

SHALL BE PERMIT-

TED ONLY WITH

THE PERMISSION

OF THE LOCAL

AUTHORITY HAVING

JURIDICTION. THE

BURGLAR ALARM

SIGNAL SHALL NOT

BE CONNECTED

TO A POLICE

EMERGENCY

NUMBER

THIS EQUIPMENT

SHOULD BE

INSTALLED

IN ACCORDANCE

WITH THE NATIONAL

FIRE PROTECTION

ASSOCIATION'S

STANDARD 72

(NATIONAL FIRE

PROTECTION

ASSOCIATION,

BATTERYMARCH

PARK, QUINCY,

MA 02169). PRINTED

INFORMATION

DESCRIBING

INSTALLATION,

TESTING,

MAINTENANCE,

EVACUATION

PLANNING AND

REPAIR SERVICE IS

TO BE PROVIDED

WITH THIS

EQUIPMENT.

820 OHMS

EOLR

ALARM

OUTPUT

10.5–13.8VDC,

2A MAX. (600mA

MAX. FOR UL

USAGE, INCLUDING

AUX POWER)

STEADY FOR

BURGLARY/PANIC,

TEMPORAL PULSE

SOUNDING FOR FIRE.

USE 702 SIREN, OR

12V BELL. SEE

INSTRUCTIONS.

FOR BELL

SUPERVISION, AND

CONNECT RESISTOR

DIRECTLY ACROSS

EXTERNAL SOUNDER.

WTP100

TOUCHPAD

1501 Yamato Road

Boca Raton, Florida 33431

ALARM STATUS

CANCEL

PANIC OFF

CODE CHIMEINSTANT

READY

TEST BYPASSMAX

STAYAWAY

2 31

5 64

897

0 #

TROUBLE

** FOR COMPLETE INFORMATION SEE INSTRUCTIONS 800-24126 OR HIGHER

-+AB

MAX. ZONE RESISTANCE: (EACH ZONE) 300 OHMS (PLUS EOLR)

(USE EOLR PART NUMBER P4100 PART OF KIT SAHDWR1)

ASSEMBLED IN MEXICO

ETL Listed

Household Fire

and Burglar

Warning Unit

800-21465 10/15 Rev.A

3091091

Conforms to UL STD 985, 1023, 1635

Classified to ANSI/SIA CP01-2010

Model LCP500-L

800-24232 3/18 Rev A

HONEYWELL GRIP HYBRID CONTROLLER

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions:

(1) This Device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation.

FCC ID: CFS8DL-GRIPH

IC: 573F-GRIPH

HVIN: GRIPH

For Patent Information see: www.honeywell.com/patents

Country of Origin: Mexico

grip-028-V0

CONTAINS MODULE:

FCC ID: RI7LE910NAV2

IC:5131A-LE910NAV2

CONTAINS MODULE:

FCC ID: RI7LE910NAV2

IC:5131A-LE910NAV2

Figure 3. FCC/IC Label Location

5. Install the ADTZWM (ZWAVE) on the edge

connector on the PCB (refer to Figure 4). Ensure

the receptacle is securely seated on the edge

connector.

6. Secure the module with the provided screw.

7. Reconnect the earth ground and battery.

8. Plug the power supply into a 24-hour, 110VAC

unswitched outlet.

GENERAL

WiFi

BATT+ GND

LTE

TX RXGND

grip-012-V0

EXT INT

SCREW

ADTZWM

MODULE

Figure 4. Installing the ADTZWM Module

Programming

Note: The ADTZWM requires a router and internet service for Wi-Fi connection.

1. Programming associated with the ADTZWM module as well as the inclusion/exclusion of Z-Wave devices is conducted through ADT

3rd Party Services and the Alarm.com MobileTech tool. On a laptop, PC or Smart Device, go to: https://3ps.adt.com and

https://alarmadmin.alarm.com/mobile.

Specifications

REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE CONTROL WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND LIMITATIONS

OF THE ENTIRE SYSTEM.

FEDERAL COMMUNICATIONS COMMISSION & ISED STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or

modifications could void the user's authority to operate the equipment.

FCC CLASS B STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause

interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in

Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• If using an indoor antenna, replace it with a quality outdoor antenna.

• Reorient the receiving antenna until interference is reduced or eliminated.

• Move the radio or television receiver away from the receiver/control.

• Move the antenna leads away from any wire runs to the receiver/control.

• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

• Consult the dealer or an experienced radio/TV technician for help.

Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Dr., Melville, NY 11747, Ph:

516-577-2000.

ISED CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC / ISED STATEMENT

This device complies with Part 15 of the FCC Rules, and ISED’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’ISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne

doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.

RF Exposure Warning

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not

be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product

procedures.

Mise en Garde

Exposition aux Frequences Radio: La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de séparation d'au moins

20 cm (7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur ou antenne, excepté en conformité

avec les procédures de produit multi transmetteur FCC et ISEDs.

Note: The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct

disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health.

USE OF THESE PRODUCTS IN COMBINATION WITH NON-HONEYWELL PRODUCTS IN A WIRELESS MESH NETWORK, OR TO ACCESS, MONITOR OR CONTROL DEVICES IN A WIRELESS

MESH NETWORK VIA THE INTERNET OR ANOTHER EXTERNAL WIDE AREA NETWORK, MAY REQUIRE A SEPARATE LICENSE FROM SIPCO, LLC. FOR MORE INFORMATION, CONTACT

SIPCO, LLC OR IPCO, LLC AT 8215 ROSWELL RD., BUILDING 900, SUITE 950, ATLANTA, GA 303350, OR AT WWW.SIPCOLLC.COM OR WWW.INTUSIQ.COM

WARRANTY & SUPPORT

For Technical Support, call 1-877-748-7628, option 3

For documentation, call Customer Service at: 1-800-238-2727 (1-800-ADT-ASAP).

For the latest warranty information, please go to:

www.resideo.com

800-24197D 3/18 Rev. D

ADT Security Services

1501 Yamato Road

Boca Raton, FL 33431

Board Dimensions: 1.625” W x 2.625” L x 0.3125” D

Input Voltage Range: 3.6

–

14V, Max 17V

Current Drain: 250mA (ADT7AIO, ADT5AIO, ADT2X16AIO)

72mA (ADTHYBWL)

Input Voltage: 3.5V (ADT7AIO, ADT5AIO, ADT2X16AIO)

13.5V (ADTHYBWL) Temperature: 32°F (0°C) to 140°F (60°C)