Garmin STPc530 OEM,AM,Mopar,KA Kit Operating instructions

Garmin
Brand
Garmin
Model
STPc530 OEM,AM,Mopar,KA Kit
Type
Operating instructions
Navus 2
™
accessory/MariNe MouNt iNstructioNs
Using the Suction Cup Mount
Use the Navus 2 accessory mount to move your Navus 2 from one location to another. You
can afx the mount to any smooth, non-porous surface. If no smooth, non-porous surface is
available, use the enclosed disk to mount the Navus 2.
Mounting the Navus 2
Position the mount and the cables so that they do not interfere with the controls or safe
operation of the location. Select a position where the Navus 2 has a relatively unobstructed
view of the sky.
To mount the Navus 2:
1. To ensure a tight grip, clean and dry the mounting surface.
2. Pull the lever on the suction cup toward you. Place the suction cup on the mounting
surface. Flip the lever toward the mounting surface.
Lever
Suction
cup tab
Mounting Surface
3. Align the ball on the end of the suction mount with the socket (hole) on the back of the
Navus 2.
Suction
cup
4. Pressrmlytosnaptheballintothesocket.
5 Rotate the Navus 2 to obtain a maximum viewing angle.
6. Plug the power cable into an available receptacle. Your unit should turn on automatically
if it is plugged in and your vehicle is running.
See the back of this page for instructions on using the enclosed disk to mount the Navus 2.
Using the Mounting Disk
WARNING: The mounting disk uses permanent adhesive that is extremely difcult to remove
after it is installed.
To mount the Navus 2 using the disk:
1. Clean and dry the area where you want to place the mounting disk.
2. Remove the backing from the permanent mounting adhesive on the bottom of the disk.
Placethediskintheselectedarea.Pressrmlyforseveralseconds.
3. Pull the lever on the suction cup up (away from the disk). Place the suction cup mount
on top of the disk.
Disk
Lever
4. Flip the lever down (toward the disk) to secure the suction cup mount to the disk.
Removing the Navus 2 and the Mount
To remove the Navus 2 from the mount, gently pull the Navus 2 off of the mount.
To remove the mount from the mounting surface, ip the lever toward you. Pull the rubber tab
on the suction cup toward you.
© 2006 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151
st
Street, Olathe, Kansas 66062, U.S.A.
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K.
Garmin Corporation
No. 68, Jangshu 2
nd
Road, Shijr, Taipei County, Taiwan
www.garmin.com
Part Number 190-00687-04 Rev. A
K6860188
Page is loading ...
Utilisation du disque de montage
AVERTISSEMENT : le disque de montage utilise un adhésif permanent extrêmement
difcile à retirer après son application.
Installation du Navus 2 avec le disque
1. Nettoyez et séchez la surface sur laquelle vous souhaitez placer le disque de montage.
2. Retirez la pellicule protectrice de l’adhésif sous le disque. Placez le disque sur la
surface de montage. Appuyez fermement pendant plusieurs secondes.
3. Tirez le levier de la ventouse vers le haut. Placez le support à ventouse sur le disque.
Disque
Levier
4. Abaissezlelevierpourbienxerlaventouseaudisque.
Retrait du Navus 2 et du support
Pour retirer le Navus 2 du support, tirez doucement sur ce dernier jusqu’à ce qu’il se décroche
du support de montage.
Pour retirer le support de la surface de montage, tirez le levier vers vous. Tirez le loquet en
caoutchouc de la ventouse vers vous.
© Garmin Ltd. ou ses liales, 2006
Garmin International, Inc.
1200 East 151
st
Street, Olathe, Kansas 66062, É.-U.
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, R.-U.
Garmin Corporation
No. 68, Jangshu 2
nd
Road, Shijr, Taipei County, Taiwan
www.garmin.com
Nº de pièce 190-00687-04, rév. A
K6860188
Page is loading ...
Uso del disco de montaje
ADVERTENCIA: el disco de montaje usa adhesivo permanente, por lo que es
extremadamente difícil retirar la unidad una vez instalada.
Para instalar la unidad Navus 2 con el disco de montaje:
1. Limpieysequelasuperciedondeinstalaráeldisco.
2. Retirelaláminadeladhesivopermanenteenlaparteinferiordeldisco.Coloqueeldisco
dondedeseeinstalarlo.Presioneconrmezadurantevariossegundos.
3. Jale la palanca de la base de succión (en dirección contraria al disco). Coloque la base
sobre el disco.
Disco
Palanca
4. Mueva la palanca hacia abajo (es decir, hacia el disco) para asegurar la base al disco.
Cómo desmontar la unidad Navus y la base
Para retirar la unidad Navus 2 de la base, basta con jalar de ella con cuidado.
Para desmontar la base de la supercie donde se la instaló, presione la palanca hacia usted. Jale
la lengüeta de goma ubicada en la base de succión hacia usted.
© 2006 Garmin Ltd. o sus subsidiarias
Garmin International, Inc.
1200 East 151
st
Street, Olathe, Kansas 66062, EE. UU.
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, Reino Unido
Garmin Corporation
No. 68, Jangshu 2
nd
Road, Shijr, Taipei County, Taiwán
www.garmin.com
Número de publicación 190-00687-04 Rev. A
K6860188
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Garmin STPc530 OEM,AM,Mopar,KA Kit Operating instructions

Garmin
Brand
Garmin
Model
STPc530 OEM,AM,Mopar,KA Kit
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents