Instructions apply to all sizes:
LOUNGER
Assembly
Instructions
Assembled View.
Hardware in this box.
BIFOLD FUTON FRAME
1A
N&D-0209
1C
i
Instructions for the Arm assembly, are packed in the Arm box.
Parts in this box.
1B
Your arm style may vary
Page 1 of 4
Twin Love seat
Protected by US
Patent Nos. 6,725,473
6,807,693 7,444,692
Seat Deck
Back Deck
Ottoman Deck
Arm (Box 1 of 2)
Small Leg
Back Deck
Seat Deck
Ottoman Deck (with Legs)
Front Stretcher (with Metal Strike Plates)
Rear Stretcher
Back Side Rails
Clevis Pins
x 2 Pieces
Locking Pins
x 2 Pieces
Barrel Nut
x 8 Pieces
Wood Button
x 4 Pieces
60mm JCB
x 8 Pieces
Allen Key
x 1 Piece
Page 2 of 4
Assembly Instructions
Prepare Arms for Assembly.2A
Fit Wooden Dowels.
Rear
stretcher
(
no
plates
)
2B
Attach Arms to Stretchers.
Your arm style may vary.
The
Front
Stretcher
has
metal
plates
which
should
face
upwards.
Using Bolts and Barrel Nuts provided with the Arms,
attach the Arms LOOSELY to the Stretchers as shown..
It is important that these bolts are left loose!
Fasten Stretcher Brackets to Arm.
NOTE:
The hardware for these steps is included with the Arms.
Some Arms may not have these features, so just skip these steps.
See below for Assembly
of the Lounger Frame.
LOUNGER BIFOLD FRAME
N&D-0209
Cleat
A.
C.
Insert the Stretcher
Bracket Cleat into
the hole provided.
Each arm requires
two brackets, front
and back.
B. IMPORTANT: Don't
fully tighten Bracket
until Stretchers are
all in place for easy
alignment.
Stretcher
Bracket
Hole for cleat
Leg
Dowel Hole
Stretcher
Bracket
16mm Bolt
Allen Key
Hole for bolt
Wooden Dowel
Stretcher
Tap dowels all the way into the middle
hole, at each end of the Stretchers
Middle
hole
Wooden Dowel
(See above)
Barrel Nuts
Allen Key -
Leave bolts LOOSE!
Bolts
Bolts
Bolts
THIS END
FRONT
Do not tighten
the Bolts at
this stage!
Be sure the holes are
free of wood chips
and saw dust.
Do not force the Bolt
as you may strip the
thread. Be sure the
thread is properly started.
Barrel Nut
Bolt
Allen Key
Screwdriver
BOLT AND BARREL NUT
ASSEMBLY SYSTEM
Insert Barrel Nuts as shown
using a screwdriver. This will
help you position the Nut in
line with the Bolt.
Bolt
Page 3 of 4
Assembly Instructions
LOUNGER BIFOLD FRAME
3A
Attach the Back Side Rails to the Back Deck.
The Back Side Rails have a Rounded end,
which assembles to the bottom Long Rail.
Using the Bolts and Barrel Nuts packed in this box,
attach the Back Side Rails to the Back Deck.
After tightening all the Bolts on Back
Deck, push fit or lightly tap the Wood
Buttons into the holes as shown.
See below for Assembly
of the Lounger Frame.
Helpful Tip:
deeper
Bottom:
To p
Mattress will sit on this
surface (Surface with
Sticker Indication)
3B Fit Back Deck into Position.
Insert the Back Deck lying flat. Insert one end first, then
gently lower the other end into position.
CAREFUL!
These can
scratch the
Arms.
All four joints
must be left
LOOSE.
N&D-0209
Back
Side Rail
Top rail of Back Deck in the
sitting position
60mm Bolts
Wood
Buttons
60mm
Bolts
Barrel Nuts
Sticker to indicate the
top of the Back Deck
Sticker to indicate
the bottom Long Rail
Barrel Nuts
Wood
Buttons
Rounded end
THIS way
Rounded end
THIS way
THIS END
FRONT
See separate page enclosed in this box for Operating Instructions.
Your arm style may vary
Page 4 of 4
Your arm style may vary
A.4A
Assembly Instructions
LOUNGER BIFOLD FRAME
Tighten all the bolts.
4B
Fit Seat Deck into Position.
See below for Assembly
of the Lounger Frame.
Fit the Seat deck between the Back Deck as
shown. Use the Clevis Pins to connect the two
decks. Secure with a Washer and Locking Pin.
Locking Pin
i
The Seat Deck has
a sticker to indicate
the top.
Clevis pin
Your arm style may vary
4C
Hook the Ottoman Deck onto the Seat Deck.
When you have the Back Deck fitted lying flat, tighten
all the Bolts. From the back, lift the Back Deck to upright
as illustrated.
Remember that the Bolts on the
Arm should be LOOSE.
Be careful not to scratch the Arms
with the Plastic Runners when you
lower the ends of the Back Deck.
This step can be tricky - it is best
done with two people
Extend the small legs on
the Ottoman Deck.
A.
Hook the Ottoman Deck
on to the Seat Deck
B.
N&D-0209
Tighten all the Bolts
CLEVIS PIN
CLEVIS PIN
Metal Hooks
Small Leg
Handles on the front
of the Ottoman Deck
Small Leg
Your Arm style
may vary from that
illustrated below.
Extending the Ottoman Deck in the Seating Position
2
Page 1 of 2
Important Note
1
Operating
Instructions
BIFOLD FUTON FRAME
LOUNGER
See next page for converting your frame to the Bed Position.
i
For your convenience and safety, we recommend that you remove
the Mattress before adjusting the position of your Futon Frame.
•
N&D-OP1-1001
a
bc
de f
gh i
The Sofa Position. Lift up from the front,
using both handles.
Gently Pull the Ottoman
Deck out, all the way.
Lower the Ottoman
Deck to the floor.
The Steamer Position.
Extend the Small Legs
for the Lounger Position.
Fold away the Small Legs.
Lift up the Ottoman Deck
with both Handles.
Gently slide back
all the way, back to
the Sofa Position.
Converting the Lounger to the Bed Position.
4
Page 2 of 2
3
N&D-OP1-1001
See previous page for extending the Ottoman Deck in the Seating Position.
i
Operating Instructions
LOUNGER BIFOLD FRAME
Your Arm style may vary
from that illustrated below
Converting back to the Lounger Position.
FROM THE FRONT:
Pull on the Back Deck,
and Push with your leg.
FROM THE BACK:
Lift up gently, up to the
Reclined Sofa Position.
Don't Forget! Pull to unlock.
bc
Carefully hook the Ottoman
Deck onto the front Rail.
Remove the Ottoman Deck.
a
bc
de f
The Lounger Position -
Remove that Matress!
Unhook the Ottoman Deck.
Pull up gently, letting the
back drop down slowly.
Important! Push to lock. Carefully hook the Ottoman
Deck onto the front Rail.
The Bed Position.
a
de f
The Lounger Position.
Push
Pull
/
