Atag VA61211MT User manual

VA61211MT

User Manual

Dishwasher

Notice d'utilisation

Lave-vaisselle

Benutzerinformation

Geschirrspüler

CONTENTS

Safety information 2

Safety instructions 3

Product description 5

Control panel 6

Programmes 6

Settings 7

Options 10

Before first use 10

Daily use 11

Hints and tips 13

Care and cleaning 14

Troubleshooting 16

Technical information 17

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read

the supplied instructions. The manufacturer is not responsible

if an incorrect installation and use causes injuries and

damages. Always keep the instructions with the appliance for

future reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

use of the appliance in a safe way and understand the

hazards involved.

• Do not let children play with the appliance.

• Keep all detergents away from children.

•

Keep children and pets away from the appliance door when

it is open.

•

Cleaning and user maintenance shall not be made by

children without supervision.

General Safety

•

This appliance is intended to be used in household and

similar applications such as:

–

farm houses; staff kitchen areas in shops, offices and

other working environments;

2

– by clients in hotels, motels, bed & breakfast and other

residential type environments.

• Do not change the specification of this appliance.

• The operating water pressure (minimum and maximum)

must be between 0.5 (0.05) / 8 (0.8) bar (Mpa)

• Obey the maximum number of 13 place settings.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its Authorised Service Centre or similarly

qualified persons in order to avoid a hazard.

• Put knives and cutlery with sharp points in the cutlery basket

with the points down or in a horizontal position.

• Do not keep the appliance door open without supervision to

prevent to fall on it.

• Before maintenance, deactivate the appliance and

disconnect the mains plug from the mains socket.

• Do not use water spray and steam to clean the appliance.

• The ventilation openings in the base (if applicable) must not

be obstructed by a carpet.

• The appliance is to be connected to the water mains using

the new supplied hose-sets. Old hose sets must not be

reused.

SAFETY INSTRUCTIONS

Installation

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Do not install or use the appliance where

the temperature is less than 0 °C.

• Obey the installation instruction supplied

with the appliance.

• Make sure that the appliance is installed

below and adjacent to safe structures.

Electrical connection

WARNING! Risk of fire and

electrical shock.

• The appliance must be earthed.

• Make sure that the electrical information

on the rating plate agrees with the

power supply. If not, contact an

electrician.

• Always use a correctly installed

shockproof socket.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the mains cable need to be

replaced, this must be carried out by our

Authorised Service Centre.

• Connect the mains plug to the mains

socket only at the end of the installation.

Make sure that there is access to the

mains plug after the installation.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

3

• This appliance complies with the E.E.C.

Directives.

• Only for UK and Ireland. The appliance

has a 13 amp mains plug. If it is

necessary to change the fuse in the

mains plug, use fuse: 13 amp ASTA (BS

1362).

Water connection

• Make sure not to cause damage to the

water hoses.

• Before you connect the appliance to

new pipes or pipes not used for a long

time, let the water flow until it is clean.

• The first time you use the appliance,

make sure that there is no leakage.

• The water inlet hose has a safety valve

and a sheath with an inner mains cable.

WARNING! Dangerous

voltage.

• If the water inlet hose is damaged,

immediately disconnect the mains plug

from the mains socket. Contact the

Authorised Service Centre to replace the

water inlet hose.

Use

• Do not sit or stand on the open door.

• Dishwasher detergents are dangerous.

Obey the safety instructions on the

detergent packaging.

• Do not drink and play with the water in

the appliance.

• Do not remove the dishes from the

appliance until the programme is

completed. There can be detergent on

the dishes.

• The appliance can release hot steam if

you open the door while a programme

operates.

• Do not put flammable products or items

that are wet with flammable products in,

near or on the appliance.

Service

• Contact the Authorised Service Centre

to repair the appliance. We recommend

only the use of original spare parts.

• When you contact the Authorised

Service Centre, ensure that you have the

following information that is available on

the rating plate.

Model :

PNC :

Serial Number :

Disposal

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the mains

supply.

• Cut off the mains cable and discard it.

• Remove the door catch to prevent

children and pets to get closed in the

appliance.

4

PRODUCT DESCRIPTION

4

3

7

9

8

10

56

11

1

2

1

Upper spray arm

2

Lower spray arm

3

Filters

4

Rating plate

5

Salt container

6

Air vent

7

Rinse aid dispenser

8

Detergent dispenser

9

Cutlery basket

10

Lower basket

11

Upper basket

Beam-on-Floor

The Beam-on-Floor is a light that shows on

the kitchen floor below the appliance door.

• When the programme starts, a red light

comes on and stays on for all the

duration of the programme.

• When the programme is completed, a

green light comes on.

• When the appliance has a malfunction,

the red light flashes.

The Beam-on-Floor goes off

when the appliance is

deactivated.

5

CONTROL PANEL

1 2

4

3

5

1

On/off button

2

Display

3

Delay button

4

Programme buttons

5

Indicators

Indicator Description

Multitab indicator.

Salt indicator. It is always off while the programme operates.

Rinse aid indicator. It is always off while the programme operates.

PROGRAMMES

Programme Degree of soil

Type of load

Programme phases Options

1)

• Normal soil

• Crockery and

cutlery

• Prewash

• Wash 50 °C

• Rinses

• Dry

• Multitab

2)

• All

• Crockery, cut-

lery, pots and

pans

• Prewash

• Wash from 45 °C to 70

°C

• Rinses

• Dry

• Multitab

3)

• Heavy soil

• Crockery, cut-

lery, pots and

pans

• Prewash

• Wash 70 °C

• Rinses

• Dry

• Multitab

4)

• Fresh soil

• Crockery and

cutlery

• Wash 60 °C or 65 °C

• Rinses

• Multitab

6

Programme Degree of soil

Type of load

Programme phases Options

5)

• All • Prewash

1)

With this programme you have the most efficient use of water and energy consumption for crockery and cutlery

with normal soil. (This is the standard programme for test institutes).

2)

The appliance senses the degree of soil and the quantity of items in the baskets . It automatically adjusts the tem-

perature and the quantity of water, the energy consumption and the programme duration.

3)

This programme has a high temperature rinsing phase for better hygiene results. During the rinsing phase, the

temperature stays at 70 °C for at least 10 minutes.

4)

With this programme you can wash a load with fresh soil. It gives good washing results in a short time.

5)

With this programme you can quickly rinse dishes to prevent remains of food to bond on dishes and odours to

form in the appliance. Do not use detergent with this programme.

Consumption values

Programme

1)

Water

(l)

Energy

(kWh)

Duration

(min)

9.9 0.932 195

7 - 12 0.6 - 1.4 40 - 150

13 - 15 1.3 - 1.5 140 - 160

9 0.9 30

4 0.1 14

1)

The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of

dishes can change the values.

Information for test institutes

For all the necessary information for test

performance, send an email to:

[email protected]

Write down the product number (PNC) that

is on the rating plate.

SETTINGS

Programme selection mode and

user mode

When the appliance is in programme

selection mode it is possible to set a

programme and to enter the user mode.

In user mode, the following settings

can be changed:

• The level of the water softener according

to the water hardness.

• The activation or the deactivation of the

acoustic signal for end of programme.

• The deactivation of the rinse aid

dispenser when you want to use the

Multitab option without rinse aid.

These settings will be saved until you

change them again.

7

How to set the programme

selection mode

The appliance is in programme selection

mode when the programme indicator

is on and the display shows the

programme duration.

When you activate the appliance, usually it

is in programme selection mode. However,

if this does not happen, you can set the

programme selection mode in the following

way:

Press and hold simultaneously and

until the appliance is in

programme selection mode.

The water softener

The water softener removes minerals from

the water supply, which would have a

detrimental effect on the washing results

and on the appliance.

The higher the content of these minerals,

the harder your water is. Water hardness is

measured in equivalent scales.

The water softener should be adjusted

according to the hardness of the water in

your area. Your local water authority can

advise you on the hardness of the water in

your area. It is important to set the right

level of the water softener to assure good

washing results.

Water hardness

German de-

grees (°dH)

French de-

grees (°fH)

mmol/l Clarke de-

grees

Water softener

level

47 - 50 84 - 90 8.4 - 9.0 58 - 63 10

43 - 46 76 - 83 7.6 - 8.3 53 - 57 9

37 - 42 65 - 75 6.5 - 7.5 46 - 52 8

29 - 36 51 - 64 5.1 - 6.4 36 - 45 7

23 - 28 40 - 50 4.0 - 5.0 28 - 35 6

19 - 22 33 - 39 3.3 - 3.9 23 - 27

5

1)

15 - 18 26 - 32 2.6 - 3.2 18 - 22 4

11 - 14 19 - 25 1.9 - 2.5 13 - 17 3

4 - 10 7 - 18 0.7 - 1.8 5 - 12 2

<4 <7 <0.7 < 5

1

2)

1)

Factory setting.

2)

Do not use salt at this level.

How to set the water softener

level

The appliance must be in programme

selection mode.

1. To enter the user mode, press and hold

simultaneously

and

until the indicators , and

start to flash and the display

is blank.

2. Press .

• The indicators and

go off.

• The indicator

continues to flash.

8

• The display shows the current

setting: e.g. = level 5.

3. Press again and again to change the

setting.

4. Press the on/off button to confirm the

setting.

The rinse aid dispenser

The rinse aid helps to dry the dishes

without streaks and stains.

The rinse aid is automatically released

during the hot rinse phase.

Use of rinse aid and multi-

tablets

When you activate the option Multitab, the

rinse aid dispenser continues to release

rinse aid. However you can deactivate the

rinse aid dispenser. In this case the drying

results may not be satisfactory.

With the rinse aid dispenser deactivated,

the rinse aid indicator is always off.

How to deactivate the rinse aid

dispenser

The appliance must be in programme

selection mode.

1. To enter the user mode, press and hold

simultaneously

and

until the indicators , and

start to flash and the display

is blank.

2. Press .

• The indicators

and go

off.

• The indicator continues to

flash.

• The display shows the current

setting.

–

= rinse aid dispenser

activated.

– = rinse aid dispenser

deactivated.

3. Press to change the setting.

4. Press the on/off button to confirm the

setting.

Acoustic signals

Acoustic signals sound when a malfunction

of the appliance occurs. It is not possible to

deactivate these acoustic signals.

There is also an acoustic signal that sounds

when the programme is completed. By

default this acoustic signal is deactivated

but it is possible to activate it.

How to activate the acoustic

signal for the end of programme

The appliance must be in programme

selection mode.

1.

To enter the user mode, press and hold

simultaneously and

until the indicators , and

start to flash and the display

is blank.

2. Press .

•

The indicators and go off.

• The indicator continues to

flash.

• The display shows the current

setting:

–

= Acoustic signal off.

– = Acoustic signal on.

3. Press to change the setting.

4. Press the on/off button to confirm the

setting.

9

OPTIONS

Desired options must be

activated every time before you

start a programme.

It is not possible to activate or

deactivate options while a

programme is running.

Not all options are compatible

with each other. If you have

selected non compatible

options, the appliance will

automatically deactivate one or

more of them. Only the

indicators of the options still

active will stay on.

Multitab

Activate this option when you use multi-

tablets that integrate the salt, rinse aid and

detergent functions. They can also contain

other cleaning or rinsing agents.

This option deactivates the release of salt.

The salt indicator does not come on.

With the use of this option the programme

duration is prolonged to increase the

cleaning and drying results with the use of

multi-tablets.

Multitab is not a permanent option and

must be selected at every cycle.

How to activate Multitab

Press and hold simultaneously

and

until the indicator comes on.

BEFORE FIRST USE

1. Make sure that the current level of

the water softener agrees with the

hardness of the water supply. If not,

adjust the level of the water

softener.

2. Fill the salt container.

3. Fill the rinse aid dispenser.

4. Open the water tap.

5. Start a programme to remove any

processing residuals that can still be

inside the appliance. Do not use

detergent and do not load the baskets.

When you start a programme, the

appliance can take up to 5 minutes to

recharge the resin in the water softener. It

seems that the appliance is not working.

The washing phase starts only after this

procedure is completed. The procedure will

be repeated periodically.

The salt container

CAUTION! Only use salt

specifically designed for

dishwashers.

The salt is used to recharge the resin in the

water softener and to assure good washing

results in the daily use.

How to fill the salt container

1. Turn the cap of the salt container

counterclockwise and remove it.

2. Put 1 litre of water in the salt container

(Only for the first time).

3. Fill the salt container with dishwasher

salt.

4.

Remove the salt around the opening of

the salt container.

10

5. Turn the cap of the salt container

clockwise to close the salt container.

Water and salt can come out

from the salt container when

you fill it. Risk of corrosion. To

prevent it, after you fill the salt

container, start a programme.

How to fill the rinse aid

dispenser

A

B

D

C

M

A

X

1

2

3

4

+

-

A

B

D

C

CAUTION! Only use rinse aid

specifically designed for

dishwashers.

1.

Press the release button (D) to open the

lid (C).

2.

Pour the rinse aid in the dispenser (A)

until the liquid reaches the fill level

'max'.

3.

Remove the spilled rinse aid with an

absorbent cloth to prevent too much

foam.

4.

Close the lid. Make sure that the release

button locks into position.

You can turn the selector of the

released quantity (B) between

position 1 (lowest quantity) and

position 4 or 6 (highest quantity).

DAILY USE

1. Open the water tap.

2. Press the on/off button to activate the

appliance.

Make sure that the appliance is in

programme selection mode.

• If the salt indicator is on, fill the salt

container.

• If the rinse aid indicator is on, fill the

rinse aid dispenser.

3. Load the baskets.

4. Add the detergent. If you use multi-

tablets, activate the option Multitab.

5. Set and start the correct programme for

the type of load and the degree of soil.

Using the detergent

30

20

A BD

C

11

20

30

B

A D

C

1. Press the release button (B) to open the

lid (C).

2.

Put the detergent, in powder or tablets,

in the compartment (A).

3.

If the programme has a prewash phase,

put a small quantity of detergent in the

compartment (D).

4.

Close the lid. Make sure that the release

button locks into position.

Setting and starting a

programme

The AUTO OFF function

This function decreases energy

consumption by deactivating automatically

the appliance when it is not operating.

The function comes into operation:

• 5 minutes after the completion of the

programme.

• After 5 minutes if the programme has

not started.

Starting a programme

1. Keep the appliance door ajar.

2. Press the on/off button to activate the

appliance. Make sure that the appliance

is in programme selection mode.

3. Press the button related to the

programme you want to start.

The display shows the programme

duration.

4. Set the applicable options.

5. Close the appliance door to start the

programme.

Starting a programme with

delay start

1. Set a programme.

2. Press again and again until the

display shows the delay time you want

to set (from 1 to 24 hours).

The delay indicator comes on.

3. Close the appliance door to start the

countdown.

While a countdown is running it is possible

to increase the delay time but not to

change the selection of the programme and

options.

When the countdown is completed, the

programme starts.

Opening the door while the

appliance operates

If you open the door while a programme is

running, the appliance stops. When you

close the door, the appliance continues

from the point of interruption.

If the door is opened for more

than 30 seconds during the

drying phase, the running

programme will end.

Cancelling the delay start while

the countdown operates

When you cancel the delay start you have

to set the programme and options again.

Press and hold simultaneously

and

until the appliance is in

programme selection mode.

Cancelling the programme

Press and hold simultaneously and

until the appliance is in

programme selection mode.

Make sure that there is detergent in the

detergent dispenser before you start a new

programme.

12

End of the programme

When the programme is completed the

display shows 0:00 .

1. Press the on/off button or wait for the

AUTO OFF function to automatically

deactivate the appliance.

2. Close the water tap.

HINTS AND TIPS

General

The following hints will ensure optimal

cleaning and drying results in daily use and

also help to protect the environment.

• Remove larger residues of food from the

dishes into the waste bin.

• Do not pre-rinse dishes by hand. When

needed, use the prewash programme (if

available) or select a programme with a

prewash phase.

• Always use the whole space of the

baskets.

• When loading the appliance, make sure

that the dishes can be completely

reached and washed by the water

released from the spray arm nozzles.

Make sure that items do not touch or

cover each other.

• You can use dishwasher detergent, rinse

aid and salt separately or you can use

the multi-tablets (e.g. ''3in1'', ''4in1'',

''All in 1''). Follow the instructions written

on the packaging.

• Select the programme according to the

type of load and degree of soil. With the

ECO programme you have the most

efficient use of water and energy

consumption for crockery and cutlery

with normal soil.

Using salt, rinse aid and

detergent

• Only use salt, rinse aid and detergent for

dishwasher. Other products can cause

damage to the appliance.

• Multi-tablets are usually suitable in areas

with a water hardness up to 21 °dH. In

areas exceeding this limit, rinse aid and

salt must be used in addition to the

multi-tablets. However, in areas with

hard and very hard water we

recommend to use solo-detergent

(powder, gel, tablets without additional

functions), rinse aid and salt separately

for optimal cleaning and drying results.

• If you use multi-tablets you can select

the Multitab option (if available). This

option increases the cleaning and drying

results with the use of multi-tablets.

• Detergent tablets do not fully dissolve

with short programmes. To prevent

detergent residues on the tableware, we

recommend that you use the tablets with

long programmes.

• Do not use more than the correct

quantity of detergent. Refer to the

instructions on the detergent packaging.

What to do if you want to stop

using multi-tablets

Before you start to use separately

detergent, salt and rinse aid do the

following procedure.

1.

Set the highest level of the water

softener.

2.

Make sure that the salt and rinse aid

containers are full.

3. Start the shortest programme with a

rinsing phase. Do not add detergent

and do not load the baskets.

4. When the programme is completed,

adjust the water softener according to

the water hardness in your area.

5. Adjust the released quantity of rinse aid.

Loading the baskets

• Only use the appliance to wash items

that are dishwasher-safe.

• Do not put in the appliance items made

of wood, horn, aluminium, pewter and

copper.

• Do not put in the appliance items that

can absorb water (sponges, household

cloths).

• Remove remaining food from the items.

13

• Make soft the remaining burned food on

the items.

• Put hollow items (cups, glasses and

pans) with the opening down.

• Make sure that cutlery and dishes do not

bond together. Mix spoons with other

cutlery.

• Make sure that glasses do not touch

other glasses.

• Put small items in the cutlery basket.

• Put light items in the upper basket.

Make sure that the items do not move.

• Make sure that the spray arm can move

freely before you start a programme.

Before starting a programme

Make sure that:

• The filters are clean and correctly

installed.

• The cap of the salt container is tight.

• The spray arms are not clogged.

• There is dishwasher salt and rinse aid

(unless you use multi- tablets).

• The position of the items in the baskets

is correct.

• The programme is applicable for the

type of load and for the degree of soil.

• The correct quantity of detergent is

used.

Unloading the baskets

1. Let the tableware cool down before you

remove it from the appliance. Hot items

can be easily damaged.

2.

First remove items from the lower

basket, then from the upper basket.

At the end of the programme

water can still remain on the

sides and on the door of the

appliance.

CARE AND CLEANING

WARNING! Before

maintenance, deactivate the

appliance and disconnect the

mains plug from the main

socket.

Dirty filters and clogged spay

arms decrease the washing

results. Make a check regularly

and, if necessary, clean them.

Cleaning the filters

The filter system is made of 3 parts.

C

B

A

1.

Turn the filter (B) counterclockwise and

remove it.

14

2. Remove the filter (C) out of filter (B).

3. Remove the flat filter (A).

4.

Wash the filters.

5. Make sure that there are no residues of

food or soil in or around the edge of the

sump.

6. Put back in place the flat filter (A). Make

sure that it is correctly positioned under

the 2 guides.

7. Reassemble the filters (B) and (C).

8.

Put back the filter (B) in the flat filter (A).

Turn it clockwise until it locks.

CAUTION! An incorrect position

of the filters can cause bad

washing results and damage to

the appliance.

Cleaning the spray arms

Do not remove the spray arms. If the holes

in the spray arms are clogged, remove

remaining parts of soil with a thin pointed

object.

External cleaning

• Clean the appliance with a moist soft

cloth.

• Only use neutral detergents.

• Do not use abrasive products, abrasive

cleaning pads or solvents.

Internal cleaning

• Carefully clean the appliance, including

the rubber gasket of the door, with a soft

moist cloth.

15

• If you regularly use short duration

programmes, these can leave deposits

of grease and limescale inside the

appliance. To prevent this, we

recommend to run long duration

programmes at least 2 times per month.

TROUBLESHOOTING

If the appliance does not start or it stops

during operation. Before you contact an

Authorised Service Centre, check if you can

solve the problem by yourself with the help

of the information in the table.

With some problems, the display

shows an alarm code.

Problem and alarm code Possible solution

You cannot activate the ap-

pliance.

• Make sure that the mains plug is connected to the mains

socket.

• Make sure that there is no damaged fuse in the fuse box.

The programme does not

start.

• Make sure that the appliance door is closed.

• Press Start.

• If the delay start is set, cancel the setting or wait for the end

of the countdown.

• The appliance has started the procedure to recharge the

resin inside the water softener. The duration of the proce-

dure is approximately 5 minutes.

The appliance does not fill

with water.

The display shows .

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is not too

low. For this information, contact your local water authority.

• Make sure that the water tap is not clogged.

• Make sure that the filter in the inlet hose is not clogged.

• Make sure that the inlet hose has no kinks or bends.

The appliance does not drain

the water.

The display shows .

• Make sure that the sink spigot is not clogged.

• Make sure that the drain hose has no kinks or bends.

The anti-flood device is on.

The display shows .

• Close the water tap and contact an Authorised Service Cen-

tre.

Once you have checked the appliance,

deactivate and activate the appliance. If the

problem occurs again, contact an

Authorised Service Centre.

For alarm codes not described in the table,

contact an Authorised Service Centre.

16

The washing and drying results are not satisfactory

Problem Possible solution

There are whitish streaks or

bluish layers on glasses and

dishes.

• The release quantity of rinse aid is too much. Adjust the

rinse aid selector to a lower position.

• The quantity of detergent is too much.

There are stains and dry water

drops on glasses and dishes.

• The released quantity of rinse aid is not sufficient. Adjust

the rinse aid selector to a higher position.

• The quality of the rinse aid can be the cause.

The dishes are wet. • The programme does not have a drying phase or has a

drying phase with low temperature.

• The rinse aid dispenser is empty.

• The quality of the rinse aid can be the cause.

• The quality of the multi-tablets can be the cause. Try a dif-

ferent brand or activate the rinse aid dispenser and use

rinse aid and multi-tablets together.

Refer to "Hints and tips" for

other possible causes.

TECHNICAL INFORMATION

Dimensions Width / height / depth (mm) 596 / 818-898 / 555

Electrical connection

1)

Voltage (V) 220 - 240

Frequency (Hz) 50

Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)

Water supply

Cold water or hot water

2)

max 60 °C

Capacity Place settings 13

Power consumption Left-on mode (W) 0.99

Power consumption Off-mode (W) 0.10

1)

Refer to the rating plate for other values.

2)

If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water

supply to decrease energy consumption.

ENVIRONMENT CONCERNS

Recycle the materials with the symbol .

Put the packaging in applicable containers

to recycle it. Help protect the environment

and human health and to recycle waste of

electrical and electronic appliances. Do not

dispose appliances marked with the symbol

with the household waste. Return the

product to your local recycling facility or

contact your municipal office.

17

Page is loading ...

100008540-A-062015

When contacting the service department, have the complete type number to hand.

En cas de contact avec le service après-vente, ayez auprès de vous le numéro de type complet.

Halten Sie die vollständige Typennummer bereit, wenn Sie mit der Kundendienstabteilung Kontakt

aufnehmen.

You will find the addresses and phone numbers of the service organisation on the guarantee card.

Les adresses et les numéros de téléphone du service après-vente se trouvent sur la carte de

garantie.

Adressen und Telefonnummern der Kundendienstorganisation finden Sie auf der Garantiekarte.

Atag VA61211MT User manual

This manual is also suitable for

Atag VA61211MT User manual

in other languages