Hotpoint FDYF 11011 G User manual

Brand: Hotpoint

Model: FDYF 11011 G

Category: Dishwashers

Type: User manual

This manual is also suitable for

English, 1

FDYF 11011 STYLE

Contents

Product Fiche, 2

Precautions and safety advice, 3-4

General safety

Disposal of old electrical appliances

Saving energy and respecting the environment

Recycling & Disposal Information

Installation, 5-6-7

Positioning and levelling

Connecting the electricity and water supplies

Technical data

Advice regarding the first wash cycle

Description of the appliance, 8

Overall view

Control panel

Loading the racks, 9-10

Lower rack

Upper rack

Adjusting the upper rack

Unsuitable crockery

Damage to glass and crockery

Start-up and use, 11

Starting the dishwasher

Measuring out the detergent

Wash cycles, 12

Table of wash cycles

Special wash cycles and options, 13

Rinse aid and refined salt, 14

Measuring out the rinse aid

Setting water hardness

Measuring out the refined salt

Care and maintenance, 15

Cutting off the water and electricity supplies

Cleaning the dishwasher

Preventing unpleasant odours

Cleaning the sprayer arms

Cleaning the water inlet filter

Cleaning the filters

Leaving the machine unused for extended periods

Troubleshooting, 16

After-Sales Service, 17

Guarantee, 18

Instructions for use

DISHWASHER

Product Fiche

Brand

HOTPOINT

Model

FDYF 11011

Rated capacity in standard place settings (1)

Energy efciency class on a scale from A+++ (low consumption) to D (high consumption)

A+

Energy consumption per year in kWh (2)

295.0

Energy consumption of the standard cleaning cycle in kWh

1.04

Power consumption of the off-mode in W

0.5

Power consumption of the left-on mode in W

5.0

Water consumption per year in litres (3)

3080.0

Drying efcacy class on a scale from G (low efcacy) to A (high efcacy)

Programme time for standard cleaning cycle in minutes

190’

The duration of the left-on mode in minutes

Noise in dB(A) Re 1pW

Built-in model

NOTES

1) The information on the label and che relates to the standard cleaning cycle, this programme is suitable to clean normally soiled

tableware and it is the most efcient programme in terms of combined energy and water consumption. The standard cleaning cycle

corresponds to the Eco cycle.

2) Based on 280 standard cleaning cycles using cold water ll and the consumption of the low power modes. Actual energy

consumption depends on how the appliance is used.

3) Based on 280 standard cleaning cycles. Actual water consumption depends on how the appliance is used.

Product Fiche

Precautions and safety advice

The appliance was designed and manufactured in

compliance with current international safety standards.

The following information has been provided for safety

reasons and should therefore be read carefully.

Keep this instruction manual in a safe place for future

reference. If the appliance is sold, given away or

moved, please ensure the manual is kept with the

machine, so that the new owner may benefit from the

advice contained within it.

Please read this instruction manual carefully: it contains

important information regarding the safe installation, use

and maintenance of the appliance.

This appliance is intended to be used in household

and similar applications such as:

- staff kitchen areas in shops, offices and other working

environments;

- farm houses;

- by clients in hotels, motels and other residential type

environments;

- bed and breakfast type environments.

General safety

• Thisapplianceisnotintendedforusebypersons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

• Childrenshouldbesupervisedtoensurethatthey

do not play with the appliance.

• Theappliancewasdesignedfordomesticuseinside

the home and is not intended for commercial or

industrial use.

• Theappliancemustbeusedbyadultsonly,towash

domestic crockery according to the instructions in

this manual.

• Theappliancemustnotbeinstalledoutdoors,even

in covered areas. It is extremely dangerous to leave

the machine exposed to rain and storms.

• Donottouchtheappliancewhenbarefoot.

• Whenunpluggingtheappliancealwayspulltheplug

from the mains socket, do not pull on the cable.

• The water supply tap must be shut off and the

plug should be removed from the electrical socket

before cleaning the appliance or carrying out any

maintenance work.

• If the appliance breaks down, do not under any

circumstances touch the internal parts in an attempt

to carry out the repair work yourself.

• Donotleanorsitontheopendooroftheappliance:

this may cause the appliance to overturn.

• Thedoorshouldnotbeleftopenasitmaycreatea

dangerous obstacle.

• Thepackagingmaterialshouldnotbeusedasatoy:

it can become a choking or suffocation hazard.

If your family includes children:

•DONOTallowchildrentoplaywiththeapplianceor

tamper with its controls.

•Keepdetergentsandrinseaidsawayfromchildren.

• Keepchildrenawayfromtheopendoorofa

dishwasher, there could still be some detergent left

inside.

Disposal of old electrical appliances

TheEuropeanDirective2012/19/EUonWaste

ElectricalandElectronicEquipment(WEEE),requires

that old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream.Oldappliancesmustbecollectedseparately

in order to optimise the recovery and recycling of

the materials they contain and reduce the impact on

human health and the environment. The crossed out

“wheeled bin” symbol on the product reminds you of

your obligation, that when you dispose of the appliance

it must be separately collected.

Consumersshouldcontacttheirlocalauthority or

retailer for information concerning the correct disposal

of their old appliance.

Saving energy and respecting the

environment

Saving water and energy

• Onlystartawashcyclewhenthedishwasherisfull.

Whilewaitingforthedishwashertobefilled,prevent

unpleasantodourswiththeSoakcycle(seeWash

Cycles).

• Selectawashcyclethatis suited to the type of

crockery and to the soil level of the crockery using

theWashcycletable:

- for dishes with a normal soil level, use the Eco

wash cycle, which guarantees low energy and water

consumption levels.

- if the load is smaller than usual activate the Half

load* option (see Start-up and use).

• Ifyour electricity supply contract gives detailsof

electricity saving time bands, run wash cycles

during the periods when a lower tariff is applied.

TheDelayedstart* button(see Start-up anduse)

helps you organise the wash cycles accordingly.

Phosphate-free and chlorine-free detergents

containing enzymes

• Westronglyrecommendthatyouusedetergents

that do not contain phosphates or chlorine, as

these products are harmful to the environment.

• Enzymesprovide a particularly effective action

at temperatures around 50°C, and as a result

detergents containing enzymes can be used in

conjunction with low-temperature wash cycles in

ordertoachievethesameresultsasanormal65°C

wash cycle.

•To avoid wasting detergent, use the product in

appropriate quantities based on the manufacturer’s

recommendations, the hardness of the water and the

soil level and quantity of the crockery. Even if they

are biodegradable, detergents contain substances

that may alter the balance of nature.

Recycling & Disposal Information

As part of Hotpoint’s continued commitment

to helping the environment, Hotpoint reserves the right

to use quality recycled components to keep down

customer costs and minimise material wastage.

Please dispose of packaging and old appliances

carefully.

To minimise risk of injury to children, remove the door,

plug and cut mains cable off flush with the appliance.

Disposeofthesepartsseparatelytoensurethatthe

appliance can no longer be plugged into a mains

socket and the door cannot be locked shut.

* Onlyavailableinselectedmodels.

If the appliance must be moved at any time, keep it

in an upright position; if absolutely necessary, it may be

tilted onto its back.

Positioning and levelling

1.Removetheappliancefromallpackagingandcheckthatit

has not been damaged during transportation.

If it has been damaged, contact the retailer and do not proceed

any further with the installation process.

2.Checkthedishwasherbyplacingitsothatitssidesorback

panel are in contact with the adjacent cabinets or even with

the wall. This appliance can also be recessed under a single

worktop

(see the Assembly instruction sheet).

3. Position the dishwasher on a level and sturdy floor. If the

floor is uneven, the front feet of the appliance may be adjusted

until it reaches a horizontal position. If the appliance is levelled

correctly, it will be more stable and much less likely to move or

cause vibrations and noise while it is operating.

*. Adjust the height of the rear foot from the front of the

appliance on the central lower part of the dishwasher, turning

a hexagonal spanner (red color) with an opening of 8 mm in a

clockwise direction to increase the height or in an anticlockwise

direction to decrease the height.

The dishwasher meets the requirements set out by the

regulations in force concerning safety and electrical equipment.

Any technical checks should be conducted exclusively by

a trained and authorised technician: Repairs carried out by

unaithorised persons will invalidate the guarantee, as well as

posing a potential hazard to the user.

The manufacturer declines all responsibility for damage to

persons or property resulting from failure to observe the above

precautions, from tampering with even a single component or

from the use of non-original spare parts.

Electrical Connection

Before inserting the plug into the electrical socket, make sure

that:

• thesocketisearthedandcomplieswithcurrentregulations;

• thesocketcanwithstandthemaximumloadoftheappliance,

which is indicated on the data plate located on the inside of

the door

(seeDescriptionoftheappliance);

• thepowersupplyvoltagefallswithinthevaluesindicatedon

the data plate on the inside of the door;

• thesocketiscompatiblewiththeplugoftheappliance.Ifthis

is not the case, ask an authorised technician to replace the

plug

(see After Sales Service)

; do not use extension cables

or multiple sockets.

Oncetheappliancehasbeeninstalled,thepowersupply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be replaced

by the manufacturer or its Technical Assistance Service in order

to prevent all potential hazards.

(See After Sales Service)

This appliance must be earthed.

Fuses:yourappliancecomesfittedwithapluganda13Afuse.If

youneedtoreplacethefuse,onlythoseratedat13AandASTA

approvedtoBS1362shouldbeused.Ifyoulosethefusecover,a

replacement may be obtained from your local authorised Service

CentreorElectricalcompany.Correctreplacementisidentified

by colour coding or the marking on base of plug.

DONOTusetheplugunlessthefusecoverisfitted.

Changing the Plug

Cutoffanddisposeofthesuppliedplugifitdoesnotfityour

socket.

ToavoidashockhazardDONOTinsertthediscarded

plug into a socket anywhere else.

Wiresinthemainsleadarecolouredaccordancewiththe

following code:

Green/Yellow- Earth

Blue  - Neutral

Brown - Live

If you change the plug, the colour of the wires in the mains lead

may not correspond with the terminal markings in the plug, which

if not coloured, could be:

EARTH ‘E’or

NEUTRAL ‘N’

LIVE  ‘L’

Changing the Mains Lead

A lead can be ordered from Hotpoint Service

UK:08709066066or

RepublicofIreland:1850302220

- If you have damaged the existing lead or require a longer one

a charge will be made. It is strongly advised that this work is

carried out by a qualified electrician.

- If the domestic wiring includes a residual current-operated

circuit breaker, ensure that it conforms to the latest regulations.

The dishwasher must not be connected to the electricity supply

while installation is being carried out.

-Thisapplianceshouldonlybeconnectedtoa230/240VAC

source, via a properly installed earthed socket.

-Usethedishwashersolelyinadomesticenvironment.

-DONOTstandorplaceheavyobjectsonthedoorwhenitis

open, this could damage the door or cause the appliance to

tip forward.

Installation

Technical data

Dimensions

width 60 cm

height 85 cm

depth 60 cm

Capacity 13 standard place-settings

Water supply

pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

Power supply voltage See appliance data plate

Total absorbed power See appliance data plate

Fuse See appliance data plate

This dishwasher conforms to the

following European Community

Directives:

-2006/95/EC (Low Voltage)

-2004/108/EC (Electromagnetic

Compatibility)

-2009/125/EC (Comm. Reg.

1016/2010) (Ecodesign)

-97/17/EC (Labelling)

-2012/19/EU Waste Electrical

and Electronic Equipment

(WEEE)

The Company shall not be held responsible for any

incidents that occur if these regulations are not observed.

Anti-condensation strip*

After installing the dishwasher, open the door and stick the

adhesive transparent strip under the wooden shelf in order to

protect it from any condensation which may form.

Connecting the water supplies

Connectiontothewaterandelectricitysuppliesshould

only be performed by a qualified technician.

The dishwasher should not stand on top of the water

hoses or the electricity supply cable.

Connecting the water inlet hose

The water inlet and outlet hoses and the electricity supply

cable may be positioned towards the right or the left in order

to achieve the best possible installation.

• Toasuitablecoldwaterconnectionpoint:beforeattaching

the hose, run the water until it is perfectly clear so that any

impurities that may be present in the water do not clog the

appliance; after performing this operation, screw the inlet

hose tightly onto a tap with a ¾ gas threaded connection.

• Toasuitablehotwaterconnectionpoint:yourdishwasher

may be provided with hot water from the mains supply (if

you have a central heating system with radiators) provided

thatitdoesnotexceedatemperatureof60°C.

Screw the hose to the tap as described for connection to

a cold water supply.

If the inlet hose is not long enough, contact a specialist

store or an authorised technician

(see Assistance)

The water pressure must be within the values indicated

in the Technical data table

(see Installation).

The hose should not be bent or compressed.

The appliance must be connected to the water supply

network using new hoses.

Donotuseoldhoses.

Ensure that the new hose supplied is connected and the old

hose is disposed of safely.

DONOTovertightenthehoseconnector,handtightis

sufficient.

Ensure the fill hose is not kinked.

Tap connections*: A range of adaptors are available to

suit your tap.

DO NOT connect the dishwasher to a single outlet

instantaneous water heater or an electric heater.

Sink Waste System

Connecttheoutlethose(withoutbendingit)toadrainduct

withaminimumdiameterof32mm.

Theoutlethosemustbeataheightrangingfrom40to80cm

(from15’’to31’’)fromthefloor/surfacewherethedishwasher

rests (A).

• beforeconnecting the drainhose,removeanyinternal

restrictions; this will prevent a build up of debris which

could cause a blockage

• removeanyrestrictionsfromthewastespigotandensure

that the sealing bung is removed (B).

ItMUSTNOTbeconnectedtoasurfacewaterdrain.

•UntietheendoftheGREYdrainagehosefromtherear

of the appliance.

•  If fitting an under sink waste disposal unit, cut out the

membrane, bung or blanking plug.

* Onlyavailableinselectedmodels.

Ensure the drain hose is securely

attached, to prevent it coming away

while the machine is in use and

causing a flood.

Fit hose to waste securely using

a “Jubilee” type clip.

Anti-flooding protection*

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water supply

in the event of anomalies or leaks from inside the appliance.

Some models are also equipped with the supplementary safety

device New Acqua Stop

*, which guarantees anti-flooding

protection even in the event of a supply hose rupture

WARNING: HAZARDOUS VOLTAGE!

Undernocircumstanceshouldthewaterinlethosebecutasit

contains live electrical parts.

TheCompanyshallnotbeheldresponsibleforanyincidents

that occur if these regulations are not observed.

Advice regarding the first wash cycle

After the installation, remove the stoppers from the racks and the

retaining elastic elements from the upper rack, if any.

Immediately before the first washing, completely fill the salt

dispenserwithwaterandaddonlythenapproximately1kgofsalt

(seechapterentitledRinseaidandrefinedsalt).Thewatermay

overflow: this is normal and is not a cause for concern. Select

thewaterhardnessvalue(seechapterentitledRinseaidand

refined salt). - After the salt has been poured into the machine,

theLOWSALTindicatorlight*switchesoff.

If the salt dispenser is not filled, the water softener and the

heating element may get damaged as a result.

The machine has a buzzer/set of tones

(depending on the

dishwasher model

) to inform the user that a command has

been implemented: power on, cycle end etc.

The symbols/indicator lights/LEDs on the control panel/

display may vary in colour and may have a flashing or fixed

light

(depending on the dishwasher model)

The display* provides useful information concerning the

type of wash cycle, wash cycle phase, remaining time,

temperature etc.

* Onlyavailableinselectedmodels.

Overall view

Description of the

appliance

*** Onlyincompletelybuilt-inmodels* Onlyavailableinselectedmodels.

The number and type of wash cycles and options may vary depending on the dishwasher model.

1. Upperrack

2. Uppersprayerarm

3. Tip-up dispensers

4. Rackheightadjuster

5. Lower rack

6. Lower sprayer arm

7. Washingfilter

8. Salt dispenser

9. Detergentdispenser,rinse-aiddispenserand

ActiveOxygendevice*

10. Dataplate

11. Controlpanel***

Control panel

Start/Pause

button and

indicator lights

Button and

indicator light

On-Off/Reset

Extra Drying option button

Half Load option button

Delayed Start

buttons

Multi-functional Tablets

option button (Tabs)

Wash-Cycle Selection buttons

Short Time Option button

Wash-cycle indicator lights

Half Load indicator lights

Low Rinse-Aid indicator light

Low Salt indicator light

Blocked Filter indicator light

Extra Drying indicator light

Multi-Functional Tablets indicator light (Tabs)

Washing and Drying indicator lights

Tap Shut-Off indicator light

Delayed Start indicator light

Short Time indicator light

Remaining Time indicator

Display

Loading the racks

Tips

Before loading the racks, remove all food residues from the

crockery and empty liquids from glasses and containers. No

preventive rinsing is needed under running water.

Arrange the crockery so that it is held in place firmly and does

not tip over; and arrange the containers with the openings facing

downwards and the concave/convex parts placed obliquely,

thus allowing the water to reach every surface and flow freely.

Make sure that the lids, handles, trays and frying pans do not

prevent the sprayer arms from rotating. Place any small items

in the cutlery basket.

Since plastic dishes and non-stick frying pans usually retain more

water drops, their drying will be not so good as that of ceramic

or stainless-steel dishes.

Lightweight items such as plastic containers should be placed

in the upper rack and arranged so that they cannot move.

After loading the appliance, make sure that the sprayer arms

can rotate freely.

Lower rack

The lower rack can hold pans, lids, dishes, salad bowls, cutlery

etc. Large plates and lids should ideally be placed at the sides.

Very soiled dishes and pans should be placed in the lower rack

because in this sector the water sprays are stronger and allow

a higher washing performance.

Several dishwasher models are fitted with tip-up sectors

They can be used in a vertical position when arranging dishes

or in a horizontal position (lower) to load pans and salad bowls

easily.

Cutlery basket

The modular basket can slide to optimise the space inside the

lower rack. It is equipped with top grilles for improved cutlery

arrangement.

Knives and other utensils with sharp edges must be placed

in the cutlery basket with the points facing downwards or they

must be positioned horizontally in the tip-up compartments on

the upper rack

Upper rack

Load this rack with delicate and lightweight crockery such as

glasses, cups, saucers and shallow salad bowls.

Several dishwasher models are fitted with tip-up sectors

They can be used in a vertical position when arranging tea/

dessert saucers or in a lower position to load bowls and food

containers.

*Onlyavailableinselectedmodelswithdifferentnumbersand

positions.

Adjusting the height of the upper rack

In order to make it easier to arrange the crockery, the upper rack

may be moved to a higher or lower position.

The height of the upper rack should be adjusted WHEN THE

RACK IS EMPTY.

NEVER raise or lower the rack on one side only.

If the rack is equipped with a Lift-Up

device*

(see figure)

, lift

it up by holding its sides. To restore the lower position, press

the levers (A) at the sides of the rack and follow the rack down.

Unsuitable crockery

• Woodencrockeryandcutlery.

• Delicatedecoratedglasses,artistichandicraftandantique

crockery. Their decorations are not resistant.

• Parts in synthetic material which do not withstand high

temperatures.

• Copperandtincrockery.

• Crockerysoiledwithash,wax,lubricatinggreaseorink.

Thecoloursofglassdecorationsandaluminium/silverpiecescan

change and fade during the washing process. Some types of

glass (e.g. crystal objects) can become opaque after a number

of wash cycles too.

Damage to glass and crockery

Causedby:

• Typeofglassandglassproductionprocess.

• Chemicalcompositionofdetergent.

• Watertemperatureofrinsecycle.

Tips:

• Only use glasses and porcelain guaranteed by the

manufacturer as dishwasher safe.

• Useadelicatedetergentsuitableforcrockery.

• Collectglassesandcutleryfromthedishwasherassoonas

the wash cycle is over.

The upper rack can be adjusted for height based on requirements:

high position to place bulky crockery in the lower rack and low

positiontomakethemostofthetip-upcompartments/sectors

by creating more space upwards.

Tip-up compartments with adjustable position

The side tip-up compartments can be positioned at three

different heights to optimize the arrangement of crockery inside

the rack.

Wineglassescanbeplacedsafelyinthetip-upcompartments

by inserting the stem of each glass into the corresponding slots.

Cutlery tray*

Some dishwasher models are fitted with a sliding tray which

can be used to hold serving utensils or small cups. For optimum

washing performance avoid positioning bulky crockery directly

below the tray. The cutlery tray can be removed

(see Figure).

Before loading the tray, make sure the supports are properly

coupled to the upper rack

(see Figure).

Start-up and use

Measuring out the detergent

A good wash result also depends on the correct amount of

detergent being used. Exceeding the stated amount does not

result in a more effective wash and increases environmental

pollution.

Based on how soiled the items are, the amount can

be adjusted to individual cases using powder or liquid

detergent.

In the case of normally soiled items, use approximately either

35 gr (powder detergent) or 35 ml (liquid detergent). If tablets

are used, one tablet will be enough.

If the crockery is only lightly soiled or it has been rinsed

with water before being placed in the dishwasher, reduce

the amount of detergent considerably.

For good washing results also follow the instructions shown

on the detergent box. For further questions please ask the

detergent producers' Advice Offices.

If the detergent dispenser is still closed, use the closing

device “A” to open it.

Introduce the detergent into the dry dispenser “B” only.

Place the amount of detergent for pre-washing directly

inside the tub.

WhenmeasuringoutthedetergentrefertotheTableofwash

cyclestoaddtheproperquantity.CompartmentB comprises

a level showing the maximum quantity of liquid or powder

detergent that can be added to each cycle.

Removedetergentresiduesfromtheedgesofthedispenser

and close the cover until it clicks.

Closethelidofthedetergentdispenserbypullingitupuntil

the closing device is secured in place.

The detergent dispenser automatically opens up at the right time

according to the wash cycle.

If all-in-one detergents are used, we recommend using the TABS

option, because it adjusts the cycle so that the best washing

and drying results are always achieved.

Only use detergent which has been specifically designed

for dishwashers.

DO NOT USE washing up liquid.

Using excessive detergent may result in foam residue

remaining in the machine after the cycle has ended.

The use of tablets is only recommended for models which

offer the MULTI-FUNCTIONAL TABLETS option.

To achieve the best results from each washing and drying

cycle, powder detergent, rinse-aid liquid and salt should

be used.

*Onlyavailableinselectedmodels.

Starting the dishwasher

1.Turnthewatertapon.

2.PresstheON/OFFbutton:TheON/OFFindicatorlight and

the display light up.

3.Openthedoorandpourinasuitableamountofdetergent

(see below).

4. Load the racks

(see Loading the racks)

and shut the door.

5. Select the wash cycle in accordance with the type of crockery

and its soil level

(see Table of wash cycles)

by pressing the

wash-cycle selection buttons.

6. Select the wash options

(see adjacent information).

7.StartthecyclebypressingtheStart/Pausebutton:Thewash

indicator light comes on and the time left to the end of the cycle

appears on the display.

8. At the end of the cycle, the display shows END. Switch off the

appliancebypressingtheON/OFFbutton,shutoffthewatertap

and unplug the appliance from the electricity socket.

9.Waitforafewminutesbeforeremovingthecrockeryinorder

toavoidburns.Unloadtheracks,beginningwiththelowerlevel.

- The machine will switch off automatically during long

periods of inactivity in order to minimise electricity

consumption.

AUTO WASH CYCLES*:some dishwasher models are

equipped with a special sensor which can be used to assess

the level of soiling and automatically select the most efficient

and economical wash cycle accordingly. The duration of the

auto wash cycles may vary due to the operation of the sensor.

Changing a wash cycle in progress

If a mistake was made in the wash cycle selection process, it is

possible to change the cycle provided that it has only just begun:

once the wash cycle has started, in order to change the wash

cycleswitchoffthemachinebypressingandholdingtheON/

OFF/Resetbutton.Switchitbackonusingthesamebuttonand

select the desired wash cycle and options.

Adding extra crockery

PresstheStart/Pausebuttonandopenthedoor,takingcareto

avoid the escaping steam, and place the crockery inside the

dishwasher.PresstheStart/Pausebutton:Thecyclewillstart

again after a long beep has been emitted.

If the delayed start has been set, at the end of the countdown

the wash cycle will not start. It will stay in Pause mode.

PresstheStart/Pausebuttontopausethemachine;thewash

cycle is stopped.

At this stage it is not possible to change the wash cycle.

Accidental interruptions

If the door is opened during the wash cycle or there is a power

cut, the cycle stops. It starts again from the point at which it

was interrupted once the door has been shut or the electricity

supply is restored.

Wash cycles

Instructions on wash-cycle selection and detergent dosage

TheECOwashcycleisthestandardcycletowhichtheenergylabeldatarefers.Itcanbeusedtowashcrockerywitha

normalsoillevelandisthemostefficientcycleintermsofenergyandwaterconsumptionforthistypeofcrockery.27

gr/ml+6gr/ml**–1Tab(**Quantityofpre-washingdetergent)

2.Heavilysoileddishesandpans(nottobeusedfordelicateitems).30gr/ml–1Tab

3.Normallysoiledpansanddishes.27gr/ml+6gr/ml**–1Tab

4.Limitedquantityofdailysoiling(idealfor4placesettings)25gr/ml–1Tab

5.Cyclefordelicateitems,whicharemoresensitivetohightemperatures30gr/ml–1Tab

6.Fastcycletobeusedforslightlydirtydishes(idealfor2placesettings)25gr/ml–1Tab

7.Pre-washwhileawaitingcompletionoftheloadwiththedishesfromthenextmeal.Nodetergent.

8.          

Standbyconsumption:Left-onmodeconsumption:5,0W-Offmodeconsumption:0.5W

Wash-cycledataismeasuredunderlaboratoryconditionsaccordingtoEuropeanStandardEN50242.

Based on the different conditions of use, the wash-cycle duration and data can change.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Wash Cycle Drying Options

Wash Cycle

Duration

Water

Consumption (l/

cycle)

Energy

Consumption

(kWh/cycle)

Eco Yes

Delayed start – Half Load – Tabs –

Extra Dry

03:10’ 11 1,04

Intensive Ye s

Delayed start – Half Load – Tabs –

Extra Dry – Short Time

02:30’ 16,5 1,65

Normal Yes

Delayed start – Half Load – Tabs –

Extra Dry – Short Time

02:00’ 16,0 1,3

Fast No Delayed start – Half Load – Tabs 01:00 11,5 1,1

Delicates Yes

Delayed start –

Half Load – Tabs – Extra Dry

01:30 12 1,1

Express 30’ No

Delayed start –

Tabs

00:30’ 8,5 0,45

Soak No

Delayed start –

Half Load

00:10’ 4 0,01

Sanitizing Yes Delayed start 01:20 11,5 1,3

High-temperaturedisinfectingcycle.Idealtocleancrockeryandfeedingbottles.30gr/ml–1Tab

Special wash cycles and Options

Extra drying*

To improve the dryness level of the crockery, press the

EXTRADRYINGbutton;theindicatorlightwillilluminate.Ifit

is pressed again the option will be deselected.

A higher temperature during the final rinsing and a longer

drying phase improve the dryness level.

The EXTRA DRYING option increases the duration of

the wash cycle.

Multi-functional tablets* (Tabs)

This option optimises washing and drying results.

When using multi-functional tablets, press the MULTI-

FUNCTIONALTABLETSbutton;thecorrespondingindicator

will light up. If the button is pressed again, the option will be

deselected.

The “Multi-functional tablets” option results in a

longer wash cycle.

The use of tablets is only recommended for models

having this option and it is not recommended with wash

cycles which do not specify the use of multi-functional

tablets.

Notes:

Optimumperformancelevelswhenusingthe“Fast"and"Express

30’”cyclescanbeachievedbyrespectingthespecifiednumber

of place settings.

Note for Test Laboratories:

forinformationoncomparativeEN

testing conditions, please send an email to the following address:

[email protected]

Half load*

If there are not many dishes to be washed, a half load cycle

may be used in order to save water, electricity and detergent.

SelectthewashcycleandpresstheHALFLOADbutton:the

indicator light will illuminate.

PresstheHALFLOADbuttontodeselectthisoption.

Remember to halve the amount of detergent.

*Onlyavailableinselectedmodels.

Delayed start

It is possible to delay the start time of the cycle for a

period of time between 1 and 24 hours:

1. Select the desired wash cycle and any other options

required,presstheDELAYEDSTARTbutton.Therelevant

symbolstartsflashing.Usethebuttons+and-toselectwhen

thewashcyclewillstart(h01,h02etc.)

2.ConfirmwiththeSTART/PAUSEbutton.Thesymbolstops

flashing and the countdown begins.

3.Oncethistimehaselapsed,theDELAYEDSTARTsymbol

switches off and the wash cycle begins.

TodeselecttheDELAYEDSTARToption,presstheDELAYED

STARTbuttonuntilthetextOFF appears.

The Delayed Start function cannot be set once a wash

cycle has been started.

Wash options*

The OPTIONS may only be set, changed or reset after

the wash cycle has been selected and before the Start/

Pause button has been pressed.

Onlytheoptionswhicharecompatiblewiththetypeofwash

cycle set may be selected. If an option is not compatible

with the selected wash cycle

(see Table of wash cycles)

, the

corresponding symbol flashes rapidly 3 times.

If an option is selected which is not compatible with another

(previously selected) option, it will flash 3 times and switch

off, while the most recently selected option will remain active.

To deselect an option which has been set by mistake, press

the corresponding button again.

Short Time option

This option can be used to reduce the duration of the main

wash cycles while maintaining the same washing and drying

performance levels.

Having selected the option, press the Short Time button. To

deselect the option, press the same button again.

To reduce consumption even further, only run the dishwasher

when it is full.

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.

Do not use table/industrial salt or washing-up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

any rinse aid. However, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard.

(Follow the instructions given on the packaging.)

Measuring out the rinse aid

Rinseaidmakesiteasierforthecrockerytodry,aswaterrunsoff

the surfaces more readily and therefore does not leave streaks

or marks. The rinse aid dispenser should be filled:

• WhentheLOWRINSEAIDindicatorlight* on the control panel

is illuminated, a reserve supply of rinse aid is still available

for1-2cycles;

1.Openthedispenser“D” by pressing and pulling up the tab

on the lid;

2. Carefully introduce the rinse aid as far as themaximum

reference notch of the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

Rinse-aid dispenser setting

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt specially designed for this type of appliance,

supplies water without limescale which is then used to wash

the crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the

water hardness level in your area. This information can be

obtained from the organisation which supplies your household

with water.

-Switch onthe dishwasher usingthe ON/OFFbutton,wait a

fewsecondsandswitchitoffusingtheON/OFFbutton.Hold

downtheStart/Pausebuttonformin.3seconds;switchonthe

machineusingtheON/OFFbuttonandaccesstheadjustment

menu - the salt indicator light is lit.

-Selectthedesiredlevel(1to5*max.basedonthedishwasher

model)using the ECO button

(water softener set to medium

level).

Press the ON/OFF button to save the setting.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH=hardnessmeasuredinGermandegrees-°f=hardness

measuredinFrenchdegrees–mmol/l=millimolesperlitre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,

make sure that the salt dispenser is never empty.

Refinedsaltremoveslimescalefromthewater,thusavoiding

the formation of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher

(seeDescription)

and should be filled:

•WhentheLOWRINSEAIDindicatorlightonthecontrolpanel

is illuminated *;

1.Removethelowerrackandunscrewthecap(anticlockwise.)

2.Thefirsttimeyoudothis:fillthewatertankrightuptoitsedge.

3. Position the funnel*

(see figure)

and fill the salt dispenser up to

theedge(approximately1kg.)Itisnormal

for a little water to leak out.

4.Removethefunnel*andwipeanysalt

residues away from the opening; rinse the

cap under running water and then screw

it on, the head facing downwards so as

to let the water flow out of the four slots

(star-shaped arrangement) in the lower part of the cap (cap

with green float

*.)

It is advisable to perform this procedure every time you add

salt to the dispenser.

Make sure the cap is screwed on tightly so that no detergent can

get into the container during the wash cycle (this could damage

the water softener beyond repair.)

Whennecessary,measureoutthesaltbeforeawashcycle

so that any saline solution which has leaked out of the salt

dispenser is removed.

*Onlyavailableinselectedmodels.

Water Hardness Table

Average salt dispenser

capacity duration

level °dH °fH mmol/l months

1 0 - 6 0 - 10 0 - 1

7months

2 6 - 11 11 - 20 1,1 - 2

5 months

3 12 - 17 21 - 30 2,1 - 3

3 months

4 17 - 34 31 - 60 3,1 - 6

2months

34 - 50 61 - 90 6,1 - 9

2/3weeks

Forvaluesbetween0°fand10°f,wedonotrecommendtheuseofsalt.

* a setting of 5 may increase cycle duration.

** 1washcycleperday.

If you are not completely satisfied with the drying results, you

can adjust the quantity of rinse aid. Switch the dishwasher on

andoffusingtheOn/Offbutton.

Pressthe Start/Pause button3 times; switch on the machine

usingtheON/OFFbuttonandaccesstheadjustmentmenu-the

rinse-aid indicator light is lit

(set to factory level).

SelectthelevelofrinseaidsupplyusingtheECOcyclebutton

(0to4max.)

Press the ON/OFF button to save the setting.

IftherinseaidlevelissettoZERO,norinseaidwillbesupplied.

TheLOWRINSEAIDindicatorlightwillnotilluminateifyourun

out of rinse aid.

• Iftherearestreaksonthecrockery,settheadjustmentdevice

toalowernumber(1-2.)

• If there are drops of water or limescale marks, set the

adjustment device to a higher number (3-4.)

If you do not add salt or rinse aid, the LOW SALT* and

LOW RINSE AID

* indicator lights will stay lit.

Shutting off the water and electricity

supplies

• Turnoffthewatertapaftereverywashcycletoavoidleaks.

• Alwaysunplug the appliance when cleaning it and when

performing maintenance work.

Cleaning the dishwasher

• Theexternalsurfacesofthemachineandthecontrolpanel

can be cleaned using a non-abrasive cloth which has been

dampenedwithwater.Donotuseabrasivedetergentsor.

solvents.

• Anymarksontheinsideoftheappliancemayberemoved

using a cloth dampened with water and a little vinegar.

Preventing unpleasant odours

• Alwayskeepthedooroftheapplianceajarinordertoavoid

moisture from forming and being trapped inside the machine.

• Cleanthesealsaroundthedooranddetergentdispensers

regularly using a damp sponge. This will avoid food becoming

trapped in the seals, which is the main cause behind the

formation of unpleasant odours.

Cleaning the sprayer arms

Food residue may become encrusted onto the sprayer arms

and block the holes used to spray the water. It is therefore

recommended that you check the arms from time to time and

clean them with a small non-metallic brush.

The two sprayer arms may both be removed.

To remove the upper sprayer

arm, turn the plastic locking ring

in an anti-clockwise direction.

The upper sprayer arm should be

replaced so that the side with the

greater number of holes is facing

upwards.

The lower sprayer arm can be

removed by pressing on the side

tabs and pulling it upwards.

Cleaning the water inlet filter*

If the water hoses are new or have not been used for an extended

period of time, let the water run to make sure it is clear and free of

impurities before performing the necessary connections. If this

precaution is not taken, the water inlet could become blocked

and damage the dishwasher.

Cleanthewaterinletfilteratthetapoutletregularly.

- Turn off the water tap.

-Unscrewtheendofthewaterinlethose,removethefilterand

clean it carefully under running water.

-Re-placethefilterandscrewthewaterhosebackintoposition.

Cleaning the filters

The filter assembly consists of three filters which remove food

residues from the washing water and then recirculate the water.

They should be cleaned if you wish to achieve the best results

in every wash.

Cleanthefiltersregularly.

The dishwasher should not be used without filters or if the

filter is loose.

•Afterseveralwashes,checkthefilterassemblyandifnecessary

clean it thoroughly under running water, using a non-metallic

brush and following the instructions below:

1. Turn the cylindrical filter C in an anti-clockwise direction and

pull it out

(fig.1).

2.RemovethecupfilterB by exerting a slight pressure on the

side flaps

(fig.2);

3. Slide out the stainless-steel plate filter A.

(fig. 3).

4. Inspect the trap and remove any food residues. NEVER

REMOVE the wash-cycle pump protection

(black detail) (fig.4).

After cleaning the filters, re-place the filter assembly and fix it in

position correctly; this is essential for maintaining the efficient

operation of the dishwasher.

Leaving the machine unused for extended

periods

• Disconnecttheappliancefromtheelectricitysupplyandshut

off the water tap.

• Leavethedooroftheapplianceajar.

•Whenyoureturn,runawashcyclewhenthedishwasheris

empty.

Care and maintenance

*Onlyavailableinselectedmodels.

Troubleshooting

*Onlyavailableinselectedmodels.

Whenevertheappliancefailstowork,checkforasolutionfromthefollowinglistbeforecallingforAssistance.

Problem: Possible causes / Solutions:

The dishwasher does not start or cannot

be controlled.

• Switch off the appliance by pressing the ON/OFF button, switch it back

on after approximately one minute and reset the cycle.

• The appliance has not been plugged in properly.

• The dishwasher door has not been shut properly.

The door won’t close.

• The lock was released. Strongly push the door until a “clacking” noise

is heard.

No water drains from the

dishwasher.

• The dishwasher cycle has not yet finished.

• The water inlet hose is bent (see Installation).

• The drain duct is blocked.

• The filter is clogged up with food residues.

The dishwasher makes excessive

noise.

• The dishes are rattling against each other or against the sprayer arms.

• An excessive amount of foam has been produced: the detergent has not

been measured out correctly or it is not suitable for use in dishwashers

(see Start-up and use).

The dishes and glasses are

covered in a white film or

limescale deposits.

• The level of refined salt is low or the dosage setting is not suited to the

hardness of the water (see Rinse aid and salt).

• The lid on the salt dispenser is not closed properly.

• The rinse aid has been used up or the dosage is too low.

The dishes and glasses are

streaked or have a bluish tinge.

• The rinse aid dosage is too high.

The crockery has not been dried

properly.

• A wash cycle without a drying cycle has been selected.

• The rinse aid has been used up or the dosage is too low (see Rinse aid

and salt).

• The rinse aid dispenser setting is not suitable.

• The crockery is made from non-stick material or plastic.

The dishes are not clean. • The racks are overloaded (see Loading the racks).

• The crockery has not been arranged properly.

• The sprayer arms cannot rotate freely.

• The wash cycle is too gentle (see Wash cycles).

• An excessive amount of foam has been produced: the detergent has not

been measured out correctly or it is not suitable for use in dishwashers

(see Start-Up and Use).

• The lid on the rinse aid compartment has not been shut correctly.

• The filter is dirty or blocked (see Care and maintenance).

• The refined salt level is low (see Rinse aid and salt).

• Switch off the appliance by pressing the ON/OFF button. Shut off the

water tap to eliminate the risk of flooding and remove the plug from the

electrical socket.

Make sure the water inlet filter has not become blocked by impurities

(see “Care and maintenance” chapter).

The dishwasher does not take any

water in - Tap shut-off alarm

(indicator light ON/OFF ashing; H2O and

tap symbol displayed; F 6 appears after a

few seconds).

• There is no water in the mains supply.

• The water inlet hose is bent (see Installation).

• Turn on the tap and the appliance will start after a few minutes.

• The appliance lock has been activated because no action was taken

when the beeps sounded.

Switch off the appliance using the ON/OFF button, turn on the tap and

switch the appliance back on after a few seconds by pressing the same

button. Re-program the appliance and restart the wash cycle.

Clogged lter alarm

The “lter” symbol on the display will light

up.

• Make sure the wash cycle has ended, open the dishwasher door

and clean the cup filter and stainless-steel filter (see “Care and

maintenance” chapter). The “blocked filter” symbol will go off when the

following cycle starts.

After Sales Service

No one is better placed to care for your Hotpoint

appliance during the course of its working life than

us - the manufacturer.

Essential Contact Information

Hotpoint Service

Wearethelargestserviceteaminthecountryoffering

youaccessto400skilledtelephoneadvisorsand1000

fully qualified engineers on call to ensure you receive fast,

reliable, local service.

UK: 08448 224 224

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following

information:

Model number:

Serial number:

Parts and Accessories

Wesupplyafullrangeofgenuinereplacementpartsas

well as accessory products that protect and hygienically

clean your appliance to keep it looking good and

functioning efficiently throughout its life.

UK: 08448 225 225

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional benefits of Hotpoint

ownership. To activate your free 5 year parts guarantee

you must register your appliance with us.

UK: 08448 24 24 24

Republic of Ireland: 01 230 0800

www.hotpointservice.co.uk

Indesit Company UK Ltd. Morley Way, Peterborough,

PE29JB

IndesitCompanyUnit49AirwaysIndustrial

Estate,Dublin17

Recycling and Disposal Information

As part of Hotpoint’s continued commitment to helping

the environment, Hotpoint reserves the right to use quality

recycled components to keep down customer costs and

minimise material wastage.

Please dispose of packaging and old appliances carefully.

To minimise risk of injury to children, remove the door,

plug and cut mains cable off flush with the appliance.

Dispose of these parts separately to ensure that the

appliance can no longer be plugged into a mains socket

and the door cannot be locked shut.

Guarantee

12 months Parts and Labour Guarantee

Yourappliancehasthebenefitofourmanufacturer’sguarantee,whichcoversthecostofbreakdownrepairsfor

twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either

workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.

This guarantee is subject to the following conditions:

- The appliance has been installed and operated correctly and in accordance with our operating and

maintenance instructions.

- The appliance is used only on the electricity or gas supply printed on the rating plate.

- The appliance has been used for normal domestic purposes only.

- The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any

person not authorised by us.

- Any repair work must be undertaken by us or our appointed agent.

- Any parts removed during repair work or any appliance that is replaced become our property.

- TheapplianceisusedintheUnitedKingdomorRepublicofIreland.

The guarantee does not cover:

- Damageresultingfromtransportation,improperuse,neglectorinterferenceorasaresultofimproper

installation.

- Replacementofanyconsumableitemoraccessory.Theseincludedbutnotlimitedto:plugs,cables,batteries,

light bulbs, fluorescent tubes and starters, covers and filters.

- Replacementofanyremovablepartsmadeofglassorplastic.

THISGUARANTEEWILLNOTAPPLYIFTHEAPPLIANCEHASBEENUSEDINCOMMERCIALORNON-

DOMESTICPREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering

your appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for our

engineer’s time. To activate the extra parts warranty on your appliance, simply call our registration line on 08448 24

24 24 (Republic of Ireland 01 230 0800)

Extended Guarantees

Weofferaselectionofprotectionplansthatenableyoutofullycoveryourselfagainsttheexpenseofrepairbills

for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226 (Republic of

Ireland 01 230 0233).

Free Helpdesk Service

Wehaveadedicatedteamwhocanprovidefreeadviceandassistancewithyourapplianceifyouexperienceany

technicaldifficultieswithinthefirst90daysofownership.SimplycallourHotpointServiceHotlineon 08448 224 224

(Republic of Ireland 0818 313 413)

for telephone assistance, or, where necessary, to arrange for an engineer to

call.

Guarantee

195113124.03

03/2014jk-XeroxFabriano

Hotpoint FDYF 11011 G User manual

Brand: Hotpoint

Model: FDYF 11011 G

Category: Dishwashers

Type: User manual

This manual is also suitable for

Download PDF

report

Hotpoint FDYF 11011 G User manual

This manual is also suitable for

Hotpoint FDYF 11011 G User manual

Related papers

Other documents