ION Audio Tailgater Bluetooth Specification

Brand: ION Audio

Model: Tailgater Bluetooth

Category: Docking speakers

Type: Specification

This manual is also suitable for

TAILGATER

Page is loading ...

BOX CONTENTS

 Battery Powered Amplifier

 (1) Microphone with Cable

 (1) Power Cable (standard IEC)

QUICKSTART GUIDE (ENGLISH)

1. Make sure all items listed on the front of this guide are included

in the box.

2. READ SAFETY INSTRUCTION BOOKLET BEFORE USING

THE PRODUCT.

3. MAKE SURE THAT YOU HAVE COMPLETELY CHARGED

THE BATTERY PRIOR TO FIRST USE FOR MAXIMUM

BATTERY LIFE.

4. Study this setup diagram.

5. Place product in an appropriate position for operation.

6. Make sure all input devices such as microphones, CD players, MP3 players, and linked amplifiers/PAs are

turned off and volume settings are set at “zero.”

7. Connect all devices as shown above.

8. Switch everything on in the following order.

i. audio input sources (i.e. microphones, instruments, CD/MP3 Players)

ii. TAILGATER

iii. any additional amplifiers

9. When shutting down, always reverse this operation by turning off:

i. any additional amplifiers

ii. TAILGATER

iii. audio input sources (i.e. microphones, instruments, CD/MP3 Players)

Go to http://www.ion-audio.com

for product registration.

(Cable sold separately)

To input on

additional

TAILGATER

(Cable sold

separately)

DIAGRAM AND PARTS DESCRIPTION

1. Microphone 1 Balanced

Input with Gain Control

(1/4” or XLR): This jack can

take either a ¼” balanced or

a XLR balanced cable.

2. Instrument/Microphone 2

Input with Gain Control

(1/4”): This mono input

accepts a ¼” input such as a

microphone, guitar, or other

musical instrument.

3. iPod/Auxuliary input with

Gain Control (Stereo

RCA): This stereo RCA

input can be used to connect a CD, MP3, or other audio source. The knob controls the level of the iPod and

the RCA input. To connect to a portable device with a 1/8” headphone jack, you need a standard 1/8”-to-RCA

adapter which is not included.

4. Master Volume Control: This knob controls the master volume of the TAILGATER.

5. iPod Charging Switch: Turn on iPod charging by setting this switch to the "Charge iPod" position.

6. Battery Level Indicator: While the unit is powered ON, these four lights indicate the power left in the battery.

Battery life varies based on volume and usage.

7. Link Output: Connect a 1/4" stereo (TRS) cable to this line-level output to connect another amplifcation

device, such as another TAILGATER.

8. Power In (IEC): Insert the included power cable here to charge the unit. Note that the TAILGATER can run off

wall power while it simultaneously charges the battery. The charge indicator illuminates when the battery is

charging.

9. Voltage Selector*: Set this to the correct voltage for your

location's standard.

10. Power ON/OFF Switch: Turns TAILGATER on or off.

Please note that while TAILGATER is connected to a

power source, it does not need to be powered on to

charge the battery.

IMPORTANT NOTES

If your sound is distorted at high volumes, please refer to the following troubleshooting scenarios:

• Input is clipping: Try lowering the input gain or the volume control on your sound source or music instrument.

• Output is clipping: Lower the main volume level.

• There is too much bass: Try adjusting the tone or EQ control on your sound source to lower the bass level.

This will allow you to play the music louder before clipping (distortion) occurs.

• The link cable: is being plugged into the instrument or MIC input instead of the RCA line input.

Important: With all speakers, an initial “break-in” period is needed to perform at optimal levels. To properly “break-

in” your TAILGATER, play an audio source at medium volume for a few hours.

SPECIFICATIONS

Input Voltage: AC 100-120V/ 60Hz 220-240V/ 50Hz

Output Wattage: 16W (THD: < 1%)

Output Voltage: 8V/4Ω

Frequency Response: Aux Input: 78Hz – 80kHz

iPod Input: 63Hz – 77kHz

Time required to fully charge the TAILGATER: ~ 6 hrs.

Battery life: 12 hrs. with typical use (at 2/3 volume)

324

* Note: Battery life may vary

based on temperature, age,

and volume usage of product.

* WARNING: U.S. users should set this

switch to "100-120V" whereas U.K. and most

European users should set this to "220-

240V."Selecting the improper voltage can

damage the unit.

Page is loading ...

www.ion-audio.com

ION Audio Tailgater Bluetooth Specification

Brand: ION Audio

Model: Tailgater Bluetooth

Category: Docking speakers

Type: Specification

This manual is also suitable for

TAILGATER

Download PDF

report

in other languages

italiano: ION Audio Tailgater Bluetooth specificazione
français: ION Audio Tailgater Bluetooth spécification
español: ION Audio Tailgater Bluetooth Especificación
Deutsch: ION Audio Tailgater Bluetooth Spezifikation
Nederlands: ION Audio Tailgater Bluetooth Specificatie

ION Audio Tailgater Bluetooth Specification

This manual is also suitable for

ION Audio Tailgater Bluetooth Specification

in other languages

Related papers

Other documents