39
4. Remove the fabric cover from the frame
(diag. 28).
To replace the fabric cover onto the frame,
repeat operations 1,2,3,4 in the reverse order,
paying special attention that the fabric cover
fi ts and adheres correctly to the frame.
Seat
The seat is formed of two rigid plastic parts
hooked to each other.
To remove the fabric cover from the seat, it is
fi rst necessary to release the upper part from
the fi xed lower part:
1. Insert a fi nger into the slot on the seat and
press the button inside, following the in-
structions provided in the “Adjusting the
reclining backrest” paragraph (Fig. 29).
2. Turn the 4 handles, until they coincide with
the OPEN symbols (diag. 30).
WARNING! At the end of the operation,
check that the small reference circles,
located on the base, and the handles are
aligned, and that the two parts are cor-
rectly unlocked.
3. Position the child car seat as shown in diag.
31, and raise the backrest to the highest
position.
4. Raise the upper part of the child car seat,
removing at the same time the rear panel
of the backrest (diag. 32).
5. Release the fabric cover, by unfastening the
5 press-studs located on the base (diag.
33).
6. Remove the cover from the upper part of
the seat (diag. 34).
To replace the fabric cover onto the frame:
7. Repeat operations 4,5,6 in the reverse or-
der, ensuring that the fabric cover fi ts onto
and adheres correctly to the frame, in par-
ticular in the red areas, which coincide with
the lap belt holes.
8. Press the button whilst pulling the rear re-
cline adjuster handle, as illustrated in Fig.
35.
9. Place the child car seat as shown in diag.
36, and raise the backrest to he highest po-
sition.
10. Replace the upper part of the seat onto the
lower fi xed part: to insert the upper part
more easily, it is recommended to recline
the upper part during the operation, as
shown in diag. 37.
WARNING! At the end of the operation, check
that the two parts coincide.
11. Re-insert the rear panel between the frame
and the fabric cover (diag. 38).
12. Place the child car seat onto a fl at surface,
as shown in diag. 39, and turn the 4 handles
to the CLOSE symbols (diag. 40).
WARNING! At the end of the operation, check
that the small reference circles, located on the
base and the handles, are aligned, and that the
two parts are locked correctly.
How to Release the Backrest /Seat
The child car seat can be used in the car only
WITH the backrest fi tted onto the seat cor-
rectly.
The backrest can be released and removed
from the seat ONLY for reasons of space, when
not in use.
To release the backrest from the seat:
1. Pull out the seat inclination adjuster handle
to the third position; following the instruc-
tions contained in the paragraph “How to
Adjust the Inclination of the Backrest”.
2. Exercise some pressure onto the backrest
towards its rear part, in the position where
the joint is fi tted to the seat, and release
the two locking devices (diag. 41).
To fi t the backrest onto the seat, repeat the
operations described above in the reverse
order.
WARNING! At the end of the above opera-
tions, check that the upper and lower parts of
the seat are correctly locked to each other.
For further information and to order any
spare parts, please contact Chicco UK Cus-
tomer Service:
Chicco U.K. Ltd.
Tel: 01623 750870 - Prospect Close
Lowmoor Road Industrial Estate
Kirby-in-Ashfi eld- Nottinghamshire - NG17
7LF - Great Britain - www.chicco.com
WARNING! The child car seat comes in
different versions: the type and number of
accessories available varies depending on the
country of use.