DeWalt D25960 User manual

Page is loading ...

2

Dansk (oversat fra original brugsvejledning) 5

Deutsch (übersetzt von den Originalanweisungen) 15

English (original instructions) 23

Español (traducido de las instrucciones originales) 31

Français (traduction de la notice d’instructions originale) 40

Italiano (tradotto dalle istruzioni originali) 49

Nederlands (vertaald vanuit de originele instructies) 58

Norsk (oversatt fra de originale instruksjonene) 67

Português (traduzido das instruções originais) 75

Suomi (käännetty alkuperäisestä käyttöohjeesta) 84

Svenska (översatt från de ursprungliga instruktionerna) 92

Türkçe (orijinal talimatlardan çevrilmiştir) 100

Ελληνικά (μετάφραση από τις πρωτότυπες οδηγίες) 109

Page is loading ...

ENGLISH

23

DEMOLITION HAMMER D25960, D25961

Congratulations!

You have chosen a DEWALT power tool. Years of experience, thorough product development and innovation

make DEWALT one of the most reliable partners for professional power tool users.

Technical Data

D25960 D25961

Voltage V 230 230

U.K. & Ireland only V 230/115 230/115

Type 1 1

Frequency Hz 50 50

Power input W 1600 1600

Impact rate min

-1

1450 1450

Impact energy (EPTA 05/2009) J 35 35

Tool holder 28 mm Hex 30 mm Hex

Chisel positions 1 1

Weight kg 18.4 16.9

L

PA

(sound pressure) dB(A) 91 91

K

PA

(sound pressure uncertainty) dB(A) 3.0 3.0

L

WA

(sound power) dB(A) 102 102

K

WA

(sound pressure uncertainty) dB(A) 3.0 3.0

Vibration total values (triax vector sum) determined according to EN 60745:

Chiselling

Vibration emission value a

h,Cheq

hand position:

one handle on main handle

and one hand on side handle

=

m/s²

6.8 6.8

both hands on main handle = m/s² 4.5 4.5

Uncertainty K = m/s²

1.5 1.5

The vibration emission level given in this information

sheet has been measured in accordance with a

standardised test given in EN 60745 and may be

used to compare one tool with another. It may be

used for a preliminary assessment of exposure.

WARNING: The declared vibration

emission level represents the main

applications of the tool. However if the

tool is used for different applications,

with different accessories or poorly

maintained, the vibration emission may

differ. This may significantly increase the

exposure level over the total working

period.

An estimation of the level of exposure to

vibration should also take into account

the times when the tool is switched off

or when it is running but not actually

doing the job. This may significantly

reduce the exposure level over the total

working period.

Identify additional safety measures to

protect the operator from the effects of

vibration such as: maintain the tool and

the accessories, keep the hands warm,

organisation of work patterns.

Fuses:

Europe 230 V tools 10 Amperes, mains

U.K. & Ireland 230 V tools 13 Amperes, in plugs

ENGLISH

24

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently

hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially

hazardous situation which, if not

avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially

hazardous situation which, if not

avoided, may result in minor or

moderate injury.

NOTICE: Indicates a practice not

related to personal injury which, if

not avoided, may result in property

damage.

Denotes risk of electric shock.

Denotes risk of fire.

EC-Declaration of Conformity

MACHINERY DIRECTIVE

OUTDOOR NOISE DIRECTIVE

D25960, D25961

DEWALT declares that these products described

under “technical data” are in compliance with:

2006/42/EC, EN 60745-1, EN 60745-2-6;

2000/14/EC, Electrical concrete breaker (hand-held),

15 kg<m<30 kg, Annex VIII, TÜV Rheinland Product

Safety GmbH (0197), D-51105 Köln, Germany,

Notified Body ID No.: 0197

Level of acoustic power according to 2000/14/EC

(Article 12, Annex III, No. 10; 15 kg<m<30 kg):

L

WA

(measured sound power level)

D25960, D25961 dB 102

L

WA

(guaranteed sound power level) dB 105

These products also comply with Directive

2004/108/EC. For more information, please contact

DEWALT at the following address or refer to the

back of the manual.

The undersigned is responsible for compilation of the

technical file and makes this declaration on behalf of

DEWALT.

Horst Grossmann

Vice President Engineering and Product

Development

D

EWALT, Richard-Klinger-Straße 11,

D-65510, Idstein, Germany

01.04.2011

WARNING: To reduce the risk of injury,

read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings

and instructions Failure to follow the

warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators. There

is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

ENGLISH

25

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the influence of

drugs, alcohol or medication. A moment of

inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off position before

connecting to power source and/or

battery pack, picking up or carrying the

tool. Carrying power tools with your finger

on the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce

dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job

better and safer at the rate for which it

was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the switch

is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories, or

storing power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and

tool bits etc., in accordance with these

instructions taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Additional Safety Instructions for

Demolition Hammers

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

ENGLISH

26

• Hold power tools by insulated gripping

surfaces when performing an operation

where the cutting tool may contact hidden

wiring or its own cord. Cutting accessory

Contacting a “live” wire may make exposed

metal parts of the tool “live” and shock the

operator.

• Be certain that the material being drilled does

not conceal electric or gas service and that

their locations have been verified with the utility

companies.

• Keep a firm grip on the tool at all times. Do not

attempt to operate this tool without holding it

with both hands. Operating this tool with one

hand will result in loss of control. Breaking

through or encountering hard materials such as

re-bar may be hazardous as well. Tighten the

side handle securely before use.

• Ensure the chisel is secured in place before

operating the tool.

• In cold-weather conditions or when the tool

has not been used for a longer period of time,

let the tool run with no load for several minutes

before use.

• When working above ground level ensure the

area below is clear.

• Do not touch the chisel or the parts close to the

chisel immediately after operation, as they may

be extremely hot and cause burns to the skin.

• Always direct the power cable to the rear, away

from the chisel.

• Do not operate this tool for long periods of

time. Vibration caused by hammer action may

be harmful to your hands and arms. Use gloves

to provide extra cushion and limit exposure by

taking frequent rest periods.

Residual Risks

The following risks are inherent to the use of

demolition hammers:

– Injuries caused by touching the hot parts of the

tool.

In spite of the application of the relevant safety

regulations and the implementation of safety

devices, certain residual risks cannot be avoided.

These are:

– Impairment of hearing.

– Risk of squeezing fingers when changing the

accessory.

– Health hazards caused by breathing dust

developed when working in concrete and/or

masonry.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual

before use.

Wear ear protection.

Wear eye protection.

DATE CODE POSITION (FIG. 1)

The Date Code (g), which also includes the year of

manufacture, is printed into the housing.

Example:

2011 XX XX

Year of Manufacture

Package Contents

The package contains:

1 Demolition hammer

1 Side handle

1 Pointed chisel

1 Plastic case

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or

accessories which may have occurred during

transport.

• Take the time to thoroughly read and

understand this manual prior to operation.

Description (ﬁ g. 1)

a. On/off switch

b. Main handle

c. Side handle clamping knob

d. Tool retainer

e. Tool holder

f. Side handle

INTENDED USE

The D25960, D25961 heavy-duty demolition

hammers are designed for heavy-duty demolition

and breaking applications.

DO NOT use under wet conditions or in presence of

flammable liquids or gases.

These heavy-duty demolition hammers are

professional power tools.

ENGLISH

27

DO NOT let children come into contact with the

tool. Supervision is required when inexperienced

operators use this tool.

Active Vibration Control

The active vibration control neutralises rebound

vibration from the hammer mechanism. Lowering

hand and arm vibration, it allows more comfortable

use for longer periods of time and extends the life of

the unit.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DEWALT service organization.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

For 115 V units with a power rating exceeding

1500 W, we recommend to fit a plug to BS4343

standard.

WARNING: 115 V units have to

be operated via a fail-safe isolating

transformer with an earth screen

between the primary and secondary

winding.

Using an Extension Cable

If an extension cable is required, use an approved

3–core extension cable suitable for the power

input of this tool (see technical data).The minimum

conductor size is 1.5 mm

2

; the maximum length is

30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENT

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-ups

or when making repairs. Be sure the

trigger switch is in the OFF position. An

accidental start-up can cause injury.

WARNING: Always wear gloves when

changing accessories. The exposed

metal parts on the tool and accessory

may become extremly hot during

operation.

Inserting and Removing 28/30 mm

Hex Accessories (ﬁ g. 3, 4)

D25960

This machine uses chisels with a 28 mm hex shank.

D25961

This machine uses chisels with a 30 mm hex shank.

Only DEWALT recommended accessories should be

used with this product.

1. Clean the chisel shank (Fig. 3).

D25960

TO FIT A CHISEL WITH GROOVE IN THE SHANK (FIG. 4A)

1. Pull the tool retainer (d) to the unlock position.

2. Hold the chisel in front of the tool holder with

the groove (h) facing upwards.

3. Insert the chisel shank into the tool holder (e).

4. Push the retainer (d) backwards to lock the

accessory in position.

5. Pull on the chisel to check if it is properly

locked. The hammering function requires

the chisel to be able to move axially several

centimetres when locked in the tool holder.

6. To remove a chisel pull back the retainer (d) and

pull the chisel out of the tool holder (e).

TO FIT A CHISEL WITH COLLAR ON THE SHANK (FIG. 4B)

1. Pull the tool retainer (d) to the unlock position.

2. Insert the chisel shank into the tool holder (e).

3. Push the retainer (d) in line with the accessory

shank to lock the accessory in position.

4. Pull on the chisel to check if it is properly

locked.The hammering function requires

the chisel to be able to move axially several

centimetres when locked in the tool holder.

ENGLISH

28

5. To remove a chisel pull back the retainer (d) and

pull the chisel out of the tool holder (e).

D25961

TO FIT A CHISEL WITH GROOVE IN THE SHANK (FIG. 4C)

1. Pull the retainer bolt (i) and turn it by 180° to the

unlock position.

2. Hold the chisel in front of the tool holder with

the groove (h) facing upwards.

3. Insert the chisel shank into the tool holder (e).

4. Pull the retainer bolt (i) and turn it by 180° back

to the lock position.

5. Pull on the chisel to check if it is properly

locked. The hammering function requires

the chisel to be able to move axially several

centimetres when locked in the tool holder.

6. To remove a chisel pull the retainer bolt (i) and

turn it by 180° to the unlock position.

Adjusting the Side Handle (ﬁ g. 1)

The side handle (f) is assembled on the machine to

suit both right- and left-hand users.

WARNING: Always operate the

machine with the side handle properly

mounted.

1. Loosen the clamp knob (c) and rotate the side

handle to the desired position.

2. Lock the side handle in place by tightening the

clamp knob (c).

OPERATION

Instructions for Use

WARNING:

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply a pressure of approx. 20 - 30 kg

to the tool. Excessive force does not

speed up chiselling but decreases tool

performance and may shorten tool life.

Proper Hand Position (ﬁ g. 2)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

IMPORTANT: The tool must be held with two hands

at all times when in use.

Horizontal applications (fig. 2A):

Proper hand position requires one hand on the side

handle (f) and the other hand on the main handle (b).

Vertical applications (fig. 2B):

Proper hand position requires both hands on the

main handle (b).

Switching On and Off (ﬁ g. 1)

Switching on: set the on/off switch (a) to position 1.

Switching off: set the on/off switch (a) to position 0.

Demolition, Chasing and Channelling

(ﬁ g. 1, 2)

1. Select the appropriate chisel, and clean its

shank.

2. Insert the chisel and check whether it is properly

locked.

3. Fit and adjust the side handle (f) and make sure

it is firmly tightened.

4. Hold the tool with two hands on the main

handle (b) or one hand on the main handle (b)

and one hand on the side handle (f). The tool

must be held with two hands at all times when

in use. Refer to Proper Hand Postion.

5. Switch on tool to run in continuous operation.

6. Always switch off the tool when work is finished

and before unplugging.

Various types of chisels are available as an option.

Only DEWALT recommended accessories should be

used with this product.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning

This machine is not user-serviceable. Take the tool

to an authorised D

EWALT repair agent periodically.

If problems occur before this time contact an

authorised DEWALT repair agent.

Accessory Maintenance (ﬁ g. 5, 6)

WARNING: These chisels can be

reground only a limited number of

times. If in doubt, contact your dealer for

recommendations.

ENGLISH

29

WARNING: Ensure that the cutting

edge does not show discolouration

caused by too much pressure. This may

impair the hardness of the accessory.

For the best results only use sharp chisel bits.

Sharpening chisel bits frequently will guarantee

long life of the chisel bits and the best performance

results.

GRINDING

Refer to figure 5 for the types of chisels to use with

this tool.

Grind the chisels on grinding discs with continuos

water flow. Refer to figure 6 for the appropriate

angles of the following chisels:

k. pointed chisel

l. flat chisel

m. wide scaling chisel

n. clay spade

FORGING

For forging:

Heat the chisel to 850–1050°C (light red–yellow).

To harden the chisel again:

• Heat the chisel to 900°C and quench it in oil.

• Then place the chisel into the oven for 1 hour at

320°C (color is light blue).

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often

as dirt is seen collecting in and around

the air vents. Wear eye protection when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

Optional Accessories

WARNING: Since accessories, other

than those offered by DEWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only D

EWALT recommended

accessories should be used with this

product.

Consult your dealer for further information on the

appropriate accessories.

Protecting the Environment

Separate collection. This product must

not be disposed of with normal

household waste.

Should you ﬁnd one day that your DEWALT product

needs replacement, or if it is of no further use to you,

do not dispose of it with household waste. Make this

product available for separate collection.

Separate collection of used products

and packaging allows materials to be

recycled and used again. Re-use of

recycled materials helps prevent

environmental pollution and reduces

the demand for raw materials.

Local regulations may provide for separate collection

of electrical products from the household, at

municipal waste sites or by the retailer when you

purchase a new product.

DEWALT provides a facility for the collection and

recycling of DEWALT products once they have

reached the end of their working life. To take

advantage of this service please return your product

to any authorised repair agent who will collect them

on our behalf.

You can check the location of your nearest

authorised repair agent by contacting your local

DEWALT office at the address indicated in this

manual. Alternatively, a list of authorised DEWALT

repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com.

ENGLISH

30

GUARANTEE

DEWALT is confident of the quality of its

products and offers an outstanding guarantee

for professional users of the product. This

guarantee statement is in addition to and in

no way prejudices your contractual rights as a

professional user or your statutory rights as a

private non-professional user. The guarantee

is valid within the territories of the Member

States of the European Union and the

European Free Trade Area.

• 30 DAY NO RISK SATISFACTION GUARANTEE •

If you are not completely satisfied with the

performance of your D

EWALT tool, simply

return it within 30 days, complete with all

original components, as purchased, to

the point of purchase, for a full refund or

exchange. The product must have been

subject to fair wear and tear and proof of

purchase must be produced.

• ONE YEAR FREE SERVICE CONTRACT •

If you need maintenance or service for your

DEWALT tool, in the 12 months following

purchase, you are entitled to one service free

of charge. It will be undertaken free of charge

at an authorised DEWALT repair agent. Proof

of purchase must be produced. Includes

labour. Excludes accessories and spare parts

unless failed under warranty.

• ONE YEAR FULL WARRANTY •

If your D

EWALT product becomes defective

due to faulty materials or workmanship

within 12 months from the date of purchase,

DEWALT guarantees to replace all defective

parts free of charge or – at our discretion –

replace the unit free of charge provided that:

• The product has not been misused;

• The product has been subject to fair

wear and tear;

• Repairs have not been attempted by

unauthorised persons;

• Proof of purchase is produced;

• The product is returned complete with all

original components.

If you wish to make a claim, contact your

seller or check the location of your nearest

authorised D

EWALT repair agent in the

D

EWALT catalogue or contact your DEWALT

office at the address indicated in this manual.

A list of authorised DEWALT repair agents and

full details of our after-sales service is available

on the Internet at: www.2helpU.com.

Page is loading ...

Belgique et Black & Decker - DEWALT Dutch Tel: +32 70 220 063 Fax: +32 70 225 585

Luxembourg Nieuwlandlaan 7, IZ Aarschot B156 French Tel: +32 70 220 062 Fax: +32 70 222 441

België en B-3200 Aarschot www.dewalt.be

Luxemburg

Danmark D

EWALT Tlf: 70201511

Sluseholmen 2-4 Fax: 70224910

2450 København SV www.dewalt.dk

Deutschland D

EWALT Tel: 06126-21-1

Richard Klinger Str. 11 Fax: 06126-21-2770

65510 Idstein www.dewalt.de

Ελλάς Black & Decker (Ελλάς) Α.Ε. Τηλ: +30 210 8981-616 www.dewalt.gr

Στράβωνος 7 & Βουλιαγμένης 159 Service: +30 210 8981-616

Γλυφάδα 16674, Αθήνα Φαξ: +30 210 8983-570

España D

EWALT Tel: 934 797 400

Parque de Negocios “Mas Blau” Fax: 934 797 419

Edificio Muntadas, c/Bergadá, 1, Of. A6 www.dewalt.es

08820 El Prat de Llobregat (Barcelona)

France D

EWALT Tel: 04 72 20 39 20

5, allée des hêtres Fax: 04 72 20 39 00

BP 30084, 69579 Limonest Cedex www.dewalt.fr

Schweiz D

EWALT Tel: 01 - 730 67 47

Suisse In der Luberzen 40 Fax: 01 - 730 70 67

Svizzera 8902 Urdorf www.dewalt.ch

Ireland D

EWALT Tel: 00353-2781800

Calpe House Rock Hill Fax: 00353-2781811

Black Rock, Co. Dublin www.dewalt.ie

Italia D

EWALT Tel: 800-014353

Viale Elvezia 2 Fax: 039-2387592

20052 Monza (Mi) www.dewalt.it

Nederlands Black & Decker - D

EWALT Tel: +31 164 283 063

Joulehof 12 Fax: +31 164 283 200

4600 AB Bergen Op Zoom www.dewalt.nl

Norge D

EWALT Tel: 45 25 13 00

Postboks 4613, Nydalen Fax: 45 25 08 00

0405 Oslo www.dewalt.no

Österreich D

EWALT Tel: 01 - 66116 - 0

Werkzeug Vertriebsges m.b.H Fax: 01 - 66116 - 14

Oberlaaerstrasse 248 www.dewalt.at

A-1230 Wien

Portugal D

EWALT Tel: 214 66 75 00

Centro de Escritórios de Sintra Avenida Almirante Fax: 214 66 75 75

Gago Coutinho, 132/134, Edifício 142710-418 Sintra www.dewalt.pt

2710-418 Lisboa

Suomi D

EWALT Puh: 010 400 430

Tekniikantie 12 Faksi: 0800 411 340

02150 Espoo, Finland www.dewalt.fi

Sverige D

EWALT Tel: 031 68 61 00

Box 94 Fax: 031 68 60 08

431 22 Mölndal www.dewalt.se

Türkiye

KALE Hırdavat ve Makina A.Ş. Tel: 0212 533 52 55

Defterdar Mah. Savaklar Cad. No:15 Faks: 0212 533 10 05

Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE www.dewalt.com.tr

United D

EWALT Tel: 01753-56 70 55 www.dewalt.co.uk

Kingdom 210 Bath Road; Slough, Berks SL1 3YD Fax: 01753-57 21 12

Middle East D

EWALT Tel: +971 4 8863030

Africa P.O. Box - 17164, Fax: +971 4 8863333

Jebel Ali (South Zone), Dubai, UAE www.dewalt.ae

N072261 05/11

DeWalt D25960 User manual

This manual is also suitable for

DeWalt D25960 User manual

in other languages

Related papers

Other documents